Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Phonic MM1002a
Summary of Contents for Phonic MM1002a
- Page 2 Use damp cloth or dry brush to clean the unit. DO NOT use any other solvents for cleaning. Good care and maintenance of your unit will prolong your unit’ s operational life and insure its optimal performance. MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 2...
-
Page 3: Table Of Contents
12 EFX............10 13 BAL............10 DEMINSIONS..........16 14 LEVEL..........10 SPECIFICATIONS..........17 OUTPUT CONNECTION & MASTER SECTION SYSTEM BLOCK DIAGRAM.......18 15 AUX OUT..........10 16 EFX OUT..........11 17 PHONES..........11 18 MAIN OUT...........11 19 CTRL RM..........11 20 REC.............11 PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 3... -
Page 4: Introduction
MAIN l/R source. and CTRL RM/Headphones Never use solvents to clean the unit; clean it • Global +48V phantom power switch for with a soft, dry cloth. channle 1~4 on master section MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 4... -
Page 5: Connecting It Up
CONNECTING IT UP PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 5... -
Page 6: Typical Connecting Lead
TYPICAL CONNECTING LEAD MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 6... -
Page 7: Unbalanced & Balanced
THE DIFFERENCE BETWEEN TWO tination unit. This connection topology is to avoid creating a grounding loop between the signal and OPERATIONS power ground. Utilize only the power ground, be- PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 7... -
Page 8: Input Channel Description
The control has a sult. shelving response that gives 15dB LINE of boost or cut at 12KHZ. The unbalanced 1/4" TS phone jack accepts line level signal from key- MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 8... -
Page 9: Low Cut
To make sound more impres- nal effect. This is very helpful in si- sive, dynamic process is necessary. multaneously adjusting the level of the processed signal. 4 LOW CUT (MM1202a ONLY) Slide down the slide-switch; insert PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 9... -
Page 10: Pan
14 LEVEL You can use one stereo input chan- nel (9/10 for MM1002a, 11/12 for A rotary fader determines the pro- MM1202a) for external effect proces- portion of the channel in the mix and sor. -
Page 11: Efx Out
CTRL RM monitor output is then replaced by This socket sends out the signals to your headphone EFX/AUX. for monitoring. On MM1002a, it is located on the connecting panel section, while on MM1202a un- der the MAIN L/R fader. -
Page 12: Headphones / Stereo
30 AUX OUT CONTROL (MM1202a ONLY) This master AUX level control determines the final level of AUX mixing bus. 31 HEADPHONES JACK This jack sends the mix signal to the headphones. MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 12... -
Page 13: Power Supply Input Socket
When more channels are added to the mixer, the meters LED may move up to the red sec- FOLLOW THE PROCEDURE FOR EACH tion. Adjust the overall level using the master CHANNEL IN USE faders if necessary. PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 13... -
Page 14: Channel As Efx Rtn
APPLICATIONS: USING STEREO INPUT CHANNEL AS EFX RTN MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 14... -
Page 15: Application : Pc Recording Setup
APPLICATIONS: PC RECORDING SETUP PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 15... -
Page 16: Deminsions
DEMINSIONS Measurements are shown in mm / inch MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 16... -
Page 17: Specifications
SPECIFICATIONS PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 17... -
Page 18: System Block Diagram
SYSTEM BLOCK DIAGRAM: MM1202a MM1002a/1202a USER’ S MANUAL PHONIC CORPORATION Page 18... - Page 19 SYSTEM BLOCK DIAGRAM: MM1002a PHONIC CORPORATION MM1002a/1202a USER’ S MANUAL Page 19...
Need help?
Do you have a question about the MM1002a and is the answer not in the manual?
Questions and answers