Phonic MU1002X User Manual

Phonic MU1002X User Manual

10-input compact mixer with dfx
Hide thumbs Also See for MU1002X:

Advertisement

MU1002X
10-Input Compact Mixer with DFX
English

Advertisement

Table of Contents
loading

Summary of Contents for Phonic MU1002X

  • Page 1 MU1002X 10-Input Compact Mixer with DFX English...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.
  • Page 3: Table Of Contents

    Effect Processor ....................9 Master Control Section ...................10 DIGITAL EFFECTS TABLE ..................11 APPLICATION .......................12 SPECIFICATIONS ....................13 DIMENSIONS ......................15 BLOCK DIAGRAM ....................16 Phonic reserves the right to improve or alter any information suppied within this document without prior notice. V1.1 OCT 25 MU1002X...
  • Page 4: Introduction

    FEATURES INTRODUCTION Congratulations on your purchase of the Phonic MU1002X - a uniquely compact 10-input mixer, with two balanced • DFX, our 24/32-bit DSP processing multi- mic/line channels as well as four stereo line channels effect processor with 16 programs plus one combined to make the perfect mixer for almost any need.
  • Page 5: Basic Setup

    4. Plug the supplied power supply into the inlet on the performer normally would during a performance; if back of the MU1002X and into an AC power outlet of a guitar is plugged into the channel, then the guitar a suitable voltage.
  • Page 6: Making Connections

    3. Stereo Channels Each of the four stereo channels of the MU1002X features two 1/4” phone jacks, for the addition of various stereo line level input devices, such as electronic keyboards, guitars, drum machines, and so forth.
  • Page 7: Rear Panel

    These outputs will accommodate typical RCA cables, able to feed a stereo signal to a variety of recording devices. Phonic’s unique mini stereo output has also been included this output is controlled using the Control Room/Phones for the addition of recording devices such as MD players, control.
  • Page 8: Controls And Settings

    This switch is used to turn the mixer on and off. Ensure all volume controls are down to a minimum before turning the MU1002X on. 17. Low Frequency Control This control is used to give a 13. Phantom Power Switch shelving boost or cut of ±15 dB...
  • Page 9: Effect Processor

    26. Program Control This control will allow users to select one of the 16 built- in digital effects of the MU1002X. The effect names that correspond with the numbers can be found on the top of the MU1002X mixer’s face, or in the digital effect table.
  • Page 10: Master Control Section

    EFX to Main control) to the Control Room/Phones mixing bus. 35. Mono Button Pushing this button in changes the stereo signal sent through the Main L and R outputs of the MU1002X to a MU1002X...
  • Page 11: Digital Effects Table

    Delay Time: 160-260 ms ; Feedback: Karaoke Delay Time & Feedback 45-65 Chorus + Rev Depth 0 – 100% Flange + Rev Modulation Frequency 0.05 – 4.00 Hz Phaser + Rev Modulation Frequency 0.05 – 4.00 Hz Tap Delay Feedback Gain 0 – 99% MU1002X...
  • Page 12: Application

    This 60 mm fader is final level control for the main left and right audio feed, sent to the Main L and R output. Live Event Application On the following couple of pages you will find a wide range of possible uses for the MU1002X mixer. Of course Additional Mixer To A PA System MU1002X...
  • Page 13: Specifications

    Frequency Response (Mic input to any output) 20Hz ~ 60KHz +0/-1 dB 20Hz ~ 100KHz +0/-3 dB Crosstalk (1KHz @ 0dBu, 20Hz to 20KHz bandwidth, channel in to main L/R outputs) Channel fader down, other channels at unity <-90 dB MU1002X...
  • Page 14 12 KHz Low Cut Filter 75Hz (-18 dB/oct) Power Requirement (external power supply, depends 100VAC, 120VAC, 220 ~ 240VAC, 50/60Hz on region) Weight 1.7 kg (3.74 lbs) Dimensions (WxHxD) 218 x 70 x 233 mm (8.15” x 2.76” x 9.17”) MU1002X...
  • Page 15: Dimensions

    DIMENSIONS 190 / 7.48 65.3 / 2.57 215. / 8.5 measurements are shown in mm / inches MU1002X...
  • Page 16: Block Diagram

    BLOCK DIAGRAM MU1002X...
  • Page 17: Warranty Information

    Phonic, at its option, shall repair or replace the defective unit covered by this warranty. Please retain the dated sales receipt as evidence of the date of purchase.

Table of Contents