Operating Instructions - Jensen Phase Linear UV10 Instruction Manual

OPERATING INSTRUCTIONS

Power On / Off
Press the /SRC button (10) on the unit (or the
on the remote control) to turn the unit on. The buttons on the
front of the unit light up and the current mode status appears
in the LCD (7). You can also turn on the unit by pressing the
OPEN button (1) and opening the TFT screen.
Press and hold the button to power off the unit.The monitor
is drawn back into the main compartment.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The
Beep tone can be disabled through the Setup menu.
Mute/Line Mute
Press the rotary encoder button (11) on the front panel or the
MUTE button (3) on the remote to mute the volume from the
unit. Press the rotary encoder button again to restore the
volume. "MUTE" is displayed on the LCD. Adjusting the
volume or using any of the audio setup features cancels the
mute function.
If the "MUTE" wire is connected, audio output mutes when a
telephone call is received by the car phone (using optional
BTM10) or when verbal navigation is performed (using
optional NAV102).
Playing Source Selection
When the monitor is closed, press the SRC button on the
front panel (10) or remote control (8) to change between
available audio playing sources in the following order: AM/
FM, DISC, USB1, USB2, BT, NAV, AUX IN and CAMERA.
The mode is displayed on the LCD screen.
Source Menu
You can also use the touch screen to change the source
through the SOURCE MENU. To access the SOURCE
MENU, touch the top left corner of the screen or press the
SRC button on the front panel (10) or remote control (8) .
button (4)
SOURCE MENU
RADIO
RADIO DISC
BT NAV
Touch the DISC, RADIO, USB1, USB2, NAVI, AUX or
CAMERA button to select the corresponding source.
NOTE: If an iPod is attached to a USB1 port, "IPOD"
appears instead of the text "USB1."
External Devices
External peripheral devices, including a game console,
camcorder, navigation unit, iPod, Zune, etc. can be
connected to this unit via RCA output using an A/V Media
Adapter Cable (not included).
A / V
INPUT
Connect the external device to the A/V Media Adapter Cable
and then plug the cable into the A/V INPUT connector (13) on
the front of the radio. Select "AUX" or "AUX IN" (when
monitor is closed) mode to access auxiliary devices. You
cannot directly control external devices connected to the A/V
INPUT. For information regarding the use of USB devices,
see "Inserting a USB Device" on page 17.
Volume Adjustment
Volume Increase/Decrease
To increase or decrease the volume level, turn the rotary
encoder (11) on the front panel or press the VOL-/+ buttons
(15, 16) on remote control. When the volume level reaches
"0" or "40", a beep sounds, indicating that the adjustment limit
has been reached. The LCD or TFT screen displays the
volume level for 3 seconds.
Programmable Turn-On Volume
USB1 USB2
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
To use this feature, the TFT monitor must be displayed.
To program a specific turn-on volume level, turn the rotary
encoder (11) to adjust the volume to the desired turn-on
AUX CAMERA
volume. Push and hold the rotary encoder while the yellow
speaker icon and level indication is displayed on the screen.
The unit will beep to confirm your turn-on volume setting.
Audio Control Menu
The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.
Touch the EQ button on the left side of the screen or press
the EQ button (32) on the remote control to display the audio
menu.
•
EJECT
•
Right Audio
1
Left Audio
2
Ground
3
4 Video
3.5mm A/V Cable (not included)
6
Use the touch screen +/- buttons to adjust the settings
for an audio feature.
To adjust an audio feature using the remote control,
perform the following steps:
a. Press the (>>|)/(| ) buttons (19, 17) to highlight
<<
the audio feature to be adjusted.
b. Press the >/|| button (18) to select the highlighted
option.
UV10