Jensen Phase Linear UV10 Instruction Manual page 13

UV10
Audio Sub-menu Features
Setting Options Function
DRC Off Employ the Dynamic Range
Control for better playback for
On
low volumes.
Loudness Off Turn bass boost on/off
On
Subwoofer Off Turn the subwoofer on/off.
On
Sub Filter 80Hz Selecting a crossover fre-
quency sets a cut-off frequency
120Hz
of the subwoofer's LPF (low-
pass filter).
160Hz
RDS Sub-menu Features
Setting Options Function
RDS Off
On
CR Off
On
Bluetooth Sub-menu Features
Setting Options Function
Bluetooth Off Disable Bluetooth function.
On Enable Bluetooth function.
Connect Manual Connect the last active mobile
phone by touching the CONNECT
icon when disconnected.
Auto Automatically connect when your
paired phone is in range.
Auto Answer Manual Manually answer calls by touching
the "call" button.
Auto The unit automatically answers all
incoming calls.
Pairing Code The default code is "1234". Touch
the keypad icon to open the keypad
and enter the pairing code or pass
key required for Bluetooth connec-
tion to your mobile phone. Not all
phones/devices require a pairing
code. The default code is "0000" for
many models.
Rating Sub-menu Features
The DVD system has a built-in parental lock feature to
prevent unauthorized persons from viewing restricted disc
content. By default, the rating system is unlocked. Once
setup, the parental lock is released only by entering the
correct password. Once the password is entered, rating is
available for setup.
Setting Options Function
Password _ _ _ _ Enter a 4-digit password to
activate the "Rating" feature.
Parental 1. Kid Safe Select the appropriate rating
Ctrl level for the intended audience.
2. G
You may override higher rat-
3. PG
ings by using your password.
4. PG-13
5. PG-R
6. R
7. NC-17
8. Adult
Load Fac- Reset Select "Reset" to restore the
tory factory default settings for the
Rating system only.
To reset the password, access the "RATING" menu and enter
the current password. Once the correct password is entered,
you can access the "Password" field and enter a new one.
NOTE: Record the password and keep it in a safe place
for future reference. The rating for each disc is marked
on the disc, disc packing, or documentation. If the rating
is not available on the disc, the parental lock feature is
unavailable. Some discs restrict only portions of the disc
and the appropriate content will play. For details, please
refer to the disc description.
Hardware Sub-menu Features
If the rear-view video camera is connected, the unit is on, and
the TFT monitor is retracted inside the unit, the TFT monitor
automatically moves into the viewing position and Camera
mode is selected upon shifting into REVERSE gear. When
shifting into DRIVE gear, the TFT monitor is retracted back
inside unit.
Setting Options Function
Camera In Normal
Mirror Reverse the camera image as
if looking through a rear-view
mirror.
9
Setting Options Function
TFT Auto On The TFT panel automatically
Open opens when the unit is turned
on.
Off You must press the OPEN but-
ton (1) to open the TFT panel.
Manual When the ignition is turned
OFF, the TFT panel DOES
NOT retract if it was previously
out
Video Input NTSC The color signals are output in
(Input cir- the standard NTSC format.
cuitry auto-
PAL The color signals are output in
detects the
the standard PAL format.
video sig-
nal from the
Auto The color signal output is
Aux In
switched automatically based
source).
on the current video input sig-
nal - NTSC or PAL.
If the monitor is in display mode, the monitor automatically
switches to CAMERA mode upon reverse driving. When the
reverse driving stops, the monitor return to its original input
mode.
P.VOL Sub-menu Features
Setting Options Function
Source Radio Choose a source for which you
would like to increase the rela-
Disc
tive volume (LEVEL).
USB1
USB2
AUX IN
NAV
BT
Level 0-6 Increase relative volume for
specified source up to 6 deci-
bels.
TS Cal (Screen Calibration)
To access the "Screen Calibration" function from the SETUP
menu, select the "TS CAL" option.
After entering calibration mode, a crosshair
corner quadrant of the screen. To begin calibration, press and
hold the crosshair for one second until it moves to the next
quadrant. Continue for each quadrant until the calibration is
completed.
appears in a