Disposizioni speciali: Misurazioni Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA...
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► CH15 User Manual...
The CH15 Hydraulic Chipping Hammer will provide safe • Do not operate the tool at oil temperatures above and dependable service if operated in accordance with 140 °F/60 °C.
Page 6
Never use the tool in an explosive atmosphere, sparks from the breaking process could ignite ex- plosive gas. • Use proper lifting techniques when handling the tool, get help from a co-worker and do not over-reach. 6 ► CH15 User Manual...
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) CH15 User Manual ◄ 7...
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 10 ► CH15 User Manual...
3. Dip or spray the entire tool. the retainer spring slot with the groove. 4. Cycle the tool hydraulically several times before 5. Install the retainer spring. storing away. 6. Connect the hoses to the tool and the hydraulic power source. CH15 User Manual ◄ 11...
Do not use the tool for applications for which it was • Always replace hoses, couplings and other parts not intended. with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. •...
Incorrect tool bit . Ensure tool bit meets specifications. Tool operates slow. Low oil flow from power unit. Check power source for proper flow. High backpressure. Check hydraulic system for excessive backpressure and correct as required. CH15 User Manual ◄ 13...
Max Pressure ........................... 2000 psi/138 bar Max Relief Pressure ......................... 2150 psi/148 bar CH15 SOUND AND VIBRATION DECLARATION: Test conducted on CH15,operated at 30 LPM input Measured A-weighted sound power level, Lwa (ref. 1pW) in decibels 104 dBA Uncertainty, Kwa, in decibels 1.9 dBA...
PISTON (CH1513101, CH1533101) CH1553101 5 GPM MODEL 31590 PISTON (CH1553101) CH1513101 8 GPM MODEL 33521 TUBE (CH1513101, CH1533101) CH1533101 8 GPM MODEL, UNDERWATER 35547 TUBE (CH1553101) SEAL KIT 35979 * DENOTES PART NUMBER IN SEAL KIT 16 ► CH15 User Manual...
Page 18
Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulic.com IMPORTANT To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulic.com and select the Warranty tab.