Stanley CH15 User Manual
  1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Tools
  5. CH15
  6. User manual

Stanley CH15 User Manual

Hydraulic chipping hammer
Hide thumbs Also See for CH15:
Table of Contents

Advertisement

Quick Links

CH15
HYDRAULIC
CHIPPING HAMMER
WARNING
WARNING
To avoid serious injury or death
S
, O
M
AFETY
PERATION AND
AINTENANCE
USER'S MANUAL
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie OR 97267-5698
503-659-5660
Copyright © 2006, The Stanley Works
FAX 503-652-1780
OPS/MAINT USA
www.stanley-hydraulic-tools.com
36098 1/2006 Ver 6
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CH15 and is the answer not in the manual?

Questions and answers

Related Manuals for Stanley CH15

Summary of Contents for Stanley CH15

  • Page 1 WARNING WARNING To avoid serious injury or death AFETY PERATION AND AINTENANCE USER’S MANUAL Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 Copyright © 2006, The Stanley Works FAX 503-652-1780 OPS/MAINT USA www.stanley-hydraulic-tools.com 36098 1/2006 Ver 6...

  • Page 3: Table Of Contents

    REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certifi ed dealer, call Stanley Hydraulic Tools at one of the numbers listed on the back of this manual and ask for a Customer Service Representative.

  • Page 4: Certificate Of Conformity

    Hereby certify that the construction plant or equipment specified hereunder: 1. Manufacturer: Stanley Hydraulic Tools, 3810 Naef Road, Milwaukie, Oregon USA 2. Representative in the Union: Stanley Svenska AB, Box 9054, 400 92 Göteborg, SWEDEN 3. Category: Hydraulic Hand Held Chipping Hammer 4.
  • Page 5 Hereby certify that the construction plant or equipment specified hereunder: 1. Manufacturer: Stanley Hydraulic Tools, 3810 Naef Road, Milwaukie, Oregon USA 2. Representative in the Union: Stanley Svenska AB, Box 9054, 400 92 Göteborg, SWEDEN 3. Category: Hydraulic Hand Held Chipping Hammer 4.

  • Page 6: Safety Symbols

    SAFETY SYMBOLS Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment. This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

  • Page 7: Safety Precautions

    If so, place the added precautions in the space provided on page 6. The CH15 Hydraulic Chipping Hammer will provide safe and dependable ser- vice if operated in accordance with the instructions given in this manual. Read and understand this manual and any stickers and tags attached to the tool and hoses before operation.

  • Page 8: Tool Stickers & Tags

    USE ONLY PARTS AND REPAIR USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERA- STANLEY AND DESCRIBED IN THE OPERA- TION MANUAL. TION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR.

  • Page 9: Hydraulic Hose Requirements

    HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydrau- lic Tools. DO NOT REMOVE THESE TAGS.

  • Page 10: Htma Requirements

    HTMA REQUIREMENTS TOOL CATEGORY HYDRAULIC SYSTEM REQUIREMENTS TYPE 1 TYPEII TYPEIII TYPE RR FLOW RATE 4-6 gpm 7-9 gpm 11-13 gpm 9-10.5 gpm (15-23 lpm) (26-34 lpm) (42-49 lpm) (34-40 lpm) TOOL OPERATING PRESSURE 2000 psi 2000 psi 2000 psi 2000 psi (at the power supply outlet) (138 bar)

  • Page 11: Operation

    OPERATION PREOPERATION PROCEDURES 2. Try turning the tool bit. If the tool bit does not turn, no further adjustment is necessary. If the tool bit turns, PREPARATION FOR INITIAL USE slide the chuck adjustor toward the tool bit end of the tool and then turn it clockwise to close the hex blocks The tool, as shipped, has no special unpacking or against the tool bit shank.

  • Page 12: Operating Procedures

    OPERATION NOTE: INSTALL TOOL BIT Partially depressing the trigger allows the tool to operate at a slow speed, making it easy to start the The CH1513101, CH1533101 and CH1553101 Chip- tool bit into the surface to be broken. ping Hammers accept standard .580 inch hex shank oval collar tool bits.

  • Page 13: Equipment Protection & Care

    fl ow. This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar.

  • Page 14: Troubleshooting

    TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always make sure the hydraulic power source is supplying the correct hydraulic fl ow and pressure as listed in the table. Use a fl owmeter known to be accurate. check the fl ow with the hydraulic fl...

  • Page 15: Specifications

    SPECIFICATIONS Oil Flow Range CH15521, CH1553101, 5 gpm Model ..............4-6 gpm/15-23 lpm CH15121, CH1513101, CH1533101, 8 gpm Model ..........7-9 gpm/26-34 lpm Pressure Range ....................1000-2000 psi/69-140 Bar Length ............................17 in./43 cm Weight ............................16 lb./7.25 kg Tool Bit Models CH15521, CH15121 ......580 in. Hex Shank or .680 in. Rnd Shank, Rnd Collar Tool Bit Models CH1513101, CH1533101, CH1553101 ........580 in.

  • Page 16: Ch15121 / Ch15521 / Ch1532101 Parts Illustration

    CH15 PARTS ILLUSTRATION...

  • Page 17: Ch15121 / Ch15521 / Ch1532101 Parts List

    CH15 PARTS LIST CH15121 / CH15521 / CH1532101 MODEL DESIGNATIONS ITEM DESCRIPTION CH15521 5 gpm Model ----- NO ITEM CH15121 8 gpm Model ----- NO ITEM ----- NO ITEM CH1532101 8 gpm Model, Underwater ----- NO ITEM 07492 SPIROL PIN...

  • Page 18: Ch1553101 / Ch1513101 / Ch1533101 Parts Illustration

    CH15 PARTS ILLUSTRATION...

  • Page 19: Ch1553101 / Ch1513101 / Ch1533101 Parts List

    CH15 PARTS LIST CH1553101 / CH1513101 / CH1533101 MODEL DESIGNATIONS ITEM DESCRIPTION CH1553101 5 gpm Model ----- NO ITEM CH1513101 8 gpm Model ----- NO ITEM ----- NO ITEM CH1533101 8 gpm Model, Underwater ----- NO ITEM 07492 SPIROL PIN...

  • Page 20: Warranty

    SEALS & DIAPHRAGMS: Seals and diaphragms installed in new tools are warranted to be free of defects in material and/or workmanship for a period of 6 months after the date of fi rst usage, or for a period of 2 years from the shipping date from Stanley, whichever period expires fi rst.
  • Page 21 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 FAX 503-652-1780 www.stanley-hydraulic-tools.com...

Table of Contents