Accessories - Chamberlain Liftmaster Elite LA500-S Installation Manual

ACCESSORIES

ENTRAPMENT PROTECTION DEVICES
PHOTOELECTRIC SENSORS (NON-CONTACT)
The photoelectric sensors are designed to detect an obstacle in the
path of the electronic beam and stop the operator. Includes
mounting brackets.
Models CPS-UN4 (through beam, LiftMaster low power accessory),
AOMRON E3K-R10K4-NR (retro-reflective), RETROAB 60-2728
(retro-reflective),
SENSING EDGE (2-WIRE, NON-MONITORED,
CONTACT)
Sensing edges can detect an obstacle upon contact and stop the
operator.
Models G65MG0204, G65MG0205, G65MGR205, and
G65MGS205
SENSING EDGE CHANNEL
Mounting channel for all MG020 type edges.
Model G65ME120C5
REMOTE CONTROLS
Chamberlain offers a variety of LiftMaster remote controls to satisfy your application needs.
Single-button to 4-button, visor or key chain. The following remote controls are compatible
with operators manufactured by Chamberlain after 1993. Contact your authorized LiftMaster
dealer for additional details and options.
3-BUTTON REMOTE CONTROL
The 3-button remote control can be programmed to control the
operator. Includes visor clip.
Model 893MAX
3-BUTTON MINI-REMOTE CONTROL
The 3-button remote control can be programmed to control the
operator. Includes key ring and fastening strip.
Model 890MAX
KEYLESS ENTRY
Enables homeowner to operate gate operator from outside by
entering a 4-digit code on a specially designed keypad.
Model 877MAX
MISCELLANEOUS
REMOTE ANTENNA EXTENSION KIT
The remote antenna extension kit allows the antenna to be
remotely installed.
Model 86LM
WIRELESS ACCESS CONTROL RECEIVER
Access control receiver for up to 450 remote controls.
Model STAR450-315
PLUG-IN LOOP DETECTOR
Low power. Conveniently plugs into existing control board.
Model LOOPDETLM
MISCELLANEOUS
LOOP DETECTOR
Low power loop detectors mounted and wired separately inside
control box. LiftMaster low power accessory.
Model LD7LP
VEHICLE SENSING PROBE
The vehicle sensing probe is buried in the ground and can detect a
car as it approaches and will then open the gate.
Model CP3
SOLAR PANEL KIT - 10 WATT
This kit is to replace or add a solar panel to the operator
application. Up to four solar panels can be connected to the
operator. Requires a 33AH battery harness (see below).
Model SOLPNL10W12V (requires 2 minimum)
SOLENOID GATE LOCK
The automatic gate lock is a solenoid-driven lock that
automatically unlocks when the gate is open and locks when the
gate is closed. Can be mounted onto a gate or post. Can be
released in case of emergency.
Model GC824-12 (12/24 Vac/dc)
MAGNETIC GATE LOCK
Outdoor magnetic lock, transformer, junction box, mounting plate
and hardware. Not for use with Solar Applications. Must be
powered separately.
Model MG1300 (12/24 Vdc)
TRANSFORMER
Model APOW3
TOROIDAL TRANSFORMER KIT (OPTIONAL)
Model LA500HDTKITXLM (for Large Metal Control Box)
This toroidal transformer kit is available for operators with
firmware versions 5.1 and higher ONLY. To verify the firmware
version refer to page 32.
BATTERIES
Gate access system batteries replace or upgrade the gate operator batteries. Two identical 12
Vdc batteries are required for each gate operator. Do not mix 7AH and 33AH batteries within a
gate operator.
7AH BATTERIES
Standard 7 AMP-Hour Battery, 12 Vdc, to replace original
batteries provided with operator. Reuse existing harnesses.
Model 29-NP712
33AH BATTERIES
Upgrade 33 AMP-Hour Battery, 12 Vdc. Ideal for solar
applications and extended battery backup. For use with Large
Metal Control Box ONLY.
Model A12330SGLPK
BATTERY TRAY
Required for 33AH applications.
Model K10-36183)
SOLAR BATTERY HARNESS
Required for 33AH applications.
Model LA500SLRHARN
48