Advertisement
TiMER
OPE~e
remote
control)
. ... .
~
. .
Using the onloff timer
Set the on and off times, function to be used and volume level. Operation
will start with the selected
function
at the on time. The sound will be
gradually increased from a no-sound
level to the volume setting (fade-in).
The power will be switched off at the off time.
The ordoff timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the Ctock is set to the correct time before setting
the timer.
Select the function for timer operation
and prepare the sources to be
used.
If the function selected
is tuner, tune into the desired band and
station.
For tape playback
If cassettes
have been loaded into both decks,
deck A takes precedence-Tape
playback will start only from the
fonvard side.
-
Adjust the volume level as desired.
Operation
1.
2.
3.
4.
5.
6.
7.
Press the TIMER button.
ma
;C
For AU: The clock is 12-hour
e
r--r-in
r--l-!
u
display.
Example:
AM 1200
~
The previous timer on time setting appears.
Press the ADJUST button within
10 seconds.
Set the timer on time by pressing
the+ or – TIME SET button, then
press the ADJUST
button (as described
under "ADJUSTING
THE
CLOCK").
,,/
,,,
'@
c!
.-
The timer off time setting appears.
Set the timer off time as described
in step 3.
The previous timer mode setting (play "@"orrecording"
@ REC") and
the current function appear.
Select the timer mode by pressing
the+ or - TIME SET button.
Each time the button
is pressed,
" @ REC
and " @ " blinks
alternately.
Select"
@ REC" for unattended
recording.
If you wish to change the function,
press the FUNCTION
button
on the front panel to select the desired function.
Press the ADJUST button.
The original display returns, then the timer operation standby mode is
activated. " @" (or"@
REC") remains lit.
Press the A /ON button to switch off the power.
For AU: Use the POWER button
instead
of the&ION
button.
"o"
(or" @ REC)
blinks during a timer controlled
operation
To switch off the power during a timer controlled
operation?, press the
~ ION button, The timer will be set in the standby mode.
To cfnemk the timer setthgs
Press the TIMER button repeatedly.
The timer settings are displayed in
the follmwing
order:
CM time
0$3 time
T%mer modeJFunction
CMginal
display returns
TooMange
the settings, press the TIMER button to select the setting to be
changed,
then press the ADJUST
button
so that the display blinks.
Chamge the setting as explained
above.
To re%easethe timer
After timing
the power on, press the TIMER button, then press the SET/
CLEAR.
To amt the timer again with the same settings
1.
Press the TIMER button, then press the SET/CLEAR.
2.
Press
the&ION
button to switch off the power.
Notec
I%the SET/CLEAR
button is pressed while the timer is being set, the
cmiginal display returns.
-
The
timer mode is released
if a power failure occurs during timer
controlled
operation.
-
_The timer may not operate
if a power failure occurs during timer
operation
standby mode.
Ustig
the sleep timer
The deep
timer automatically
switches off the power after a preset time
has reiapsed. The volume will gradually
be reduced (fade-out) during the
I-miknrte
period before
the unit turns off. There are 12 time periods
availkrble:
120,
110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Pre+as the SLEEP button repeatedly
to select the desired sleep time.
\l/
SLEEP
QC
\l/
e'
~
3Z
"SLEEP"
and the selected time blink on the display. After several seconds,
the wiginal
display returns. "SLEEF
blinks.
Tcr dteck
the remaining
sleep time
Press the SLEEP button. The remaining
time is displayed. After several
seczmds, the original display returns.
To walease the sleep timer
while
in operation
Press the SLEEP button, then press the SET/CLEAR.
The timer is also
refke.ased if the power is switched
off.
16
,)
Advertisement
