Initialization Of B, C, D; Initializing The C; Modification Of C - Sony DCR-TRV890E Service Manual

3-2. INITIALIZATION OF B, C, D PAGE DATA
1. Initializing the C Page Data
Note: If the page C data is initialized, the following adjustments must be
performed again.
1) Modification of C page data
2) Servo system, RF system adjustments
Adjusting page C
Adjusting Address 00 to DF
Initializing Method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 80, set data: 0C, and press the PAUSE
button of the adjustment remote commander.
3) Check that the data of page: 3, address: 80 is changed to "1C".
4) Perform "Modification of C Page Data".
2. Modification of C Page Data
If the C Page data has been initialized, change the data of the "Fixed
data-2" address shown in the following table by manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C Page data
1) Select page: 2, address: 00, and set data: 29.
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
3) Perform the "Servo System, RF System Adjustments".
3. C Page Table
Note 1: Fixed data-1 : Initialized data. (Refer to "1. Initializing the C Page
Data".)
Fixed data-2 : Modified data. (Refer to "2. Modification of C PAGE
Data").
Initial value
Address
NTSC PAL
00 Fixed data-1
01 (Initialized data)
02
03
04
05
06
07
08
09
0A
0B
0C
0D
Remark
5-34
Initial value
Address
NTSC PAL
0E Fixed data-1
0F (Initialized data)
10 EE EE Switching position adj.
11 00 00
12 EE EE
13 00 00
14 Fixed data-1
15
16 E0 E0 Cap FG duty adj.
17 E0 E0 T reel FG duty adj.
18 2A 2A AEQ adj.
19 2A 2A
1A Fixed data-1
1B 33 33 AEQ adj.
1C 33 33
1D Fixed data-1
1E 25 25 AGC center level adj.
1F 3E 3E PLL f
20 3E 3E
21 DC DC APC adj.
22 99 99 LPF f
23 Fixed data-1
24
25 88 88 S VIDEO out Y level adj.
26 E3 E3 S VIDEO out Cr level adj.
27 A1 A1 S VIDEO out Cb level adj.
28 8A 8A IR video carrier freq. adj.
29 2D 2D IR video deviation Adj.
2A 52 52 IR audio deviation Adj.
2B 04 04 Chroma BPF adj.
2C Fixed data-2
2D Fixed data-1
2E Fixed data-2
2F (Modified data, copy the data built in
30 the same model.)
31
32 Fixed data-1
33
34 Fixed data-2
35 Fixed data-1
36
37
38 00 00 Emergency memory address
39 00 00
3A 00 00
3B 00 00
3C 00 00
3D 00 00
3E 00 00
3F 00 00
40 00 00
41 00 00
42 00 00
43 00 00
44 Fixed data-1
Remark
adj.
0
adj.
0