SMC Networks ZSE10 Series Installation & Maintenance Manual page 3

ZISE##-TFM113GB
Setting (Continued)
Function selection mode
In measurement mode, press the button for 2 seconds or longer to
display [F 0]. Select to display the function setting to be changed, [F
Press the button for 2 seconds or longer in function selection mode to
return to measurement mode.
Measurement mode
Press the button
for 2s or longer.
Function selection mode
Setting functions
*: Some functions are not available depending on part number. All functions are
displayed with [F ] and followed with function description. If a function is not
available for specified type, the function is displayed as [---].
To set each function in detail, refer to the operation manual.
Other Functions
•Peak/Bottom hold value indication
•Zero clear
•Key lock
To set each function in detail, refer to the operation manual.
Maintenance
How to reset the product for power cut or forcible de-energizing
The setting of the product will be retained as it was before a power cut or
de-energizing.
The output condition is also basically recovered to that before a power
cut or de-energizing, but may change depending on the operating
environment. Therefore, check the safety of the whole system before
operating the product.
If the system is using accurate control, wait until the pressure switch has
warmed up (approximately 10 minutes)
Error Indication Function
This function is to display error location and content when a problem or
an error occurs.
Error Troubleshooting
Error Name Error Nature
Display Method
Turn the power off and
remove the output
Over A load current of switch
factor for the over
current output is 80 mA or
current.
Error more.
Then turn the power
on.
During zero clear
operation, pressure
over 7%F.S.
±
( 3.5%F.S.for Perform zero clear
±
compound pressure) is operation again after
Zero-clear applied. After 1 s, the restoring the applied
Error mode will reset to the pressure to an
measurement mode. atmospheric pressure
1%F.S. of the zero condition.
±
clear range varies
with individual product
differences.
Error Indication Function (Continued)
Error
Error Name Error type
Display
].
Pressure has exceeded
the upper limit of the set
pressure range.
Reset applied pressure
Pressurizing
to a level within the set
Error
pressure range.
Pressure has exceeded
the lower limit of the set
pressure range.
Turn the power off and
turn it on again.
Displayed in the case of
System If resetting fails, an
an internal
Error investigation by
data error.
SMC CORPORATION
will be required.
If the error can not be reset after the above measures are taken, then
please contact SMC.
Troubleshooting
Refer to the operation manual for this product.
Specification
Refer to the operation manual and catalogue for this product.
Outline with Dimensions (in mm)
Refer to the operation manual and catalogue for this product.
Troubleshooting
Method
Contact
AUSTRIA (43) 2262 62280 NETHERLANDS (31) 20 531 8888
BELGIUM (32) 3 355 1464 NORWAY (47) 67 12 90 20
CZECH REP. (420) 541 424 611 POLAND (48) 22 211 9600
DENMARK (45) 7025 2900 PORTUGAL (351) 21 471 1880
FINLAND (358) 207 513513 SLOVAKIA (421) 2 444 56725
FRANCE (33) 1 6476 1000 SLOVENIA (386) 73 885 412
GERMANY (49) 6103 4020 SPAIN (34) 945 184 100
GREECE (30) 210 271 7265 SWEDEN (46) 8 603 1200
HUNGARY (36) 23 511 390 SWITZERLAND (41) 52 396 3131
IRELAND (353) 1 403 9000 UNITED KINGDOM (44) 1908 563888
ITALY (39) 02 92711
URL http://www.smcworld.com (Global) http://www.smceu.com (Europe)
Specifications are subject to change without prior notice from the manufacturer.
©2008 SMC Corporation All Rights Reserved.