Air King Professional Series Important Instructions & Operating Manual

Air King Professional Series Important Instructions & Operating Manual

Advantage professional series
Hide thumbs Also See for Professional Series:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

IMPORTANT INSTRUCTIONS -
Advantage
Professional Series
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

GENERAL SAFETY INFORMATION

electric shock and injury to person, including the following:
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
AND INJURY TO PERSON, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer.If you
have questions, contact the manufacturer.
b) Before servicing or cleaning the unit, switch power off at
service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service panel.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
AND INJURY TO PERSON, OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-related construction.
b) Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment manufacturer's
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA) and the American
Society for Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
CAUTION:
TO REDUCE THE RISK OF FIRE AND TO PROPERLY
EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE - DO NOT VENT
EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES, OR GARAGES.
d) Ducted fans must always be vented to the outdoors.
e) This unit must be grounded.
f) To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power unit.
g) Read all instructions before installing or using exhaust fan.
A111597016 Rev. A 12-09
OPERATING MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
SAVE THESE INSTRUCTIONS
WARNING:
NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.
WARNING:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambéing food (ie. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan filter.
d) Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING:
THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
d) Use an extinguisher ONLY if:
I.
II. The fire is small and contained in the area where it started.
III. The fire department is being called.
IV. You can fight the fire with your back to an exit.
WARNING:
DUCTWORK.
www.airkinglimited.com
Range Hood
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DO
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
TO REDUCE THE RISK OF INJURY TO PERSONS IN
You know you have a Class ABC extinguisher, and you
already know how to operate it.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
1 of 16

Advertisement

Table of Contents
loading

Summary of Contents for Air King Professional Series

  • Page 1: General Safety Information

    IMPORTANT INSTRUCTIONS - OPERATING MANUAL Advantage Range Hood Professional Series READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2: Installation Instructions

    INSTALLATION INSTRUCTIONS NOTE: When determining the height of the canopy from the cooking surface, be sure to take into consideration items such as back splashes with shelves and other accessories that might need more clearance under the canopy. CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. SECTION 3 SECTION 1 Measuring the Installation 1. Determine where the top of the hood will be located within your installation and Preparing the Range Hood tape the included wall mounting template in place (Figure 3). 1. Unpack hood from the carton and confirm that all pieces are present. In addition to the range hood you should have: Wood Mounting Strip 1 - Package containing: .75" 3 - 2" wood screws 8 - 3/4" wood screws (36" models: 12) 15.5"...
  • Page 3 SECTION 4 Installing Backsplash Wood Mounting 1. If an optional BS Series backsplash will be utilized, this must be installed before Screw the hood canopy because the hood canopy will cover the backsplash mounting Strip screws. Refer to the instructions included with the backsplash for installation. SECTION 5 Wall Anchor Hood Wall Mounted Canopy Installation Figure 8 CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES. 4. Connect the ducting to the outlet adapter and damper. Secure in place using tape to seal all joints (Figure 9). WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. Ducting 1. Determine the type of ducting you will require (Figure 6).
  • Page 4 NOTE: If the recommended, optional BS Series backsplash is being installed, use Outlet Adapter the template to locate and drill the appropriate holes for mounting. The back splash must be installed before the hood canopy because the hood canopy will cover the backsplash mounting screws. Refer to the instructions included with the backsplash Screw for complete installation instructions. 5. Rest the cavity in the back side of the hood on the wood strip and secure hood to wood strip with the included 3/4" screws through the holes in the back of the hood Hood Flange that line up with the wood strip (use 6 screws for 30" and 36" widths and 8 screws for larger widths) Secure the bottom of the hood by installing the screws provided into the wall anchors (Figure 12). Cabinet Figure 14 9. Connect the ducting to the outlet adapter and damper. Secure in place using tape Wood to seal all joints (Figure 15). Mounting Strip Screw Ducting Damper Outlet Adapter Wall Anchor Hood Hood Figure 12 Figure 15 6. From inside the hood canopy, secure hood to the underside of the cabinet by using four wood screws (not included) through the keyhole slots of the hood (Figure 12). SECTION 7 CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL...
  • Page 5: Blower Switch

    SECTION 12 SECTION 8 Maintenance Installing the Blower CAUTION: 1. Refer to the instructions included with the blower for installation. MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT. SECTION 9 Grease Filters Installing the Optional Soffits Included with your range hood are grease filters along with a grease trough that should 1. Refer to the instructions included with the specific soffit(s) you have chosen for be washed at least once a month. The grease filters are dishwasher safe and should installation. be washed in a mild soap or detergent. Reverse the instruction in SECTION 10 Finishing the Installation, to remove the grease filters and trough. If the grease filters become SECTION 10 damaged, replace with Air King Models: Finishing the Installation...
  • Page 6: Troubleshooting Guide

    DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES.
  • Page 7 REPLACEMENT PARTS DIAGRAM - 18" MODELS All 18" High Models # Qty. Description Replacement Part # 1 1 Wire Box 5S1138002 2 1 Main Wire 5S1138003 3 1 Cabinet - 30" models 5S1138630 1 Cabinet - 36" models 5S1138640 4 1 Grease Tray - 30" 5S1138230 1 Grease Tray - 36" 5S1138240 5 3 Grease Filter 30" models...
  • Page 8 REPLACEMENT PARTS DIAGRAM - 10" MODELS All 10" High Models # Qty. Description Replacement Part # 2 1 Wire Box 5S1138002 3 1 Main Wire 5S1138003 4 1 Cabinet - 30" models 5S1138030 1 Cabinet - 36" models 5S1138040 5 1 Rear Panel 30" models 5S1138130 1 Rear Panel 36" models 5S1138140 1 Rear Panel heat lamp models...
  • Page 9: Instructions Générales De Sécurité

    INSTRUCTIONS IMPORTANTES – MODE D’EMPLOI Séries Professionnelles Hotte de Cuisine Advantage LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ. FAILLIR À SE CONFORMER AUX INSTRUCTIONS PEUT RÉSULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE À...
  • Page 10 INSTRUCTIONS D’INSTALLATION REMARQUE : Lorsque vous déterminez la hauteur entre le couvert et la surface de cuisson, assurez-vous de prendre en considération les articles tels que dosseret avec AVERTISSEMENT : tablettes et autres accessoires qui pourraient avoir besoin d’un plus grand dégagement VOUS ASSURER QUE L’ALIMENTATION EST sous le couvert. COUPÉE AU PANNEAU DE SERVICE AVANT DE COMMENCER L’INSTALLATION. SECTION 3 SECTION 1 Mesurage de l’installation Préparation de la hotte de cuisinière 1. Déterminez où le dessus de la hotte sera situé dans votre installation et collez le 1. Sortir la hotte de son emballage et confirmer que toutes les pièces sont présentes. gabarit de montage mural compris en place avec du ruban adhésif (Figure 3).
  • Page 11 SECTION 4 Installation du clapet anti-retour Bande de 1. Si un clapet anti-retour optionnel de Série BS sera utilisé, celui-ci doit être installé montage avant le couvert de la hotte parce que le couvert de la hotte couvrira les vis de en bois montage du clapet anti-retour. Référez-vous aux instructions comprises avec le clapet anti-retour pour l’installation. Ancrages SECTION 5 muraux Hotte Installation au mur de couvert de la hotte Figure 8 AVERTISSEMENT : TOUS LES CONDUITS DOIVENT ÊTRE CON- FORMES AUX CODES DU BÂTIMENT LOCAUX ET NATIONAUX. 4. Raccordez les conduits à l’adaptateur de sortie et du clapet. Fixez en place en utilisant du ruban de gaine pour sceller tous les joints (Figure 9).
  • Page 12 REMARQUE : Si le dosseret recommandé, optionnel des Séries BS est installé, utilisez Adaptateur de le gabarit pour la localisation et percez les trous appropriés pour le montage. Le sortie dosseret doit être installé avant le couvert de la hotte parce que le couvert de la hotte couvrira les vis de montage du dosseret. Référez-vous aux instructions comprises avec le dosseret pour les instructions complètes d’installation. 5. Faire reposer la cavité sur le côté arrière de la hotte sur la bande de bois et fixer Hotte à la bande de bois avec les vis de .75 po comprises au travers des trous dans Bride l’arrière de la hotte qui s’alignent avec la bande de bois (utiliser les 6 vis pour les largeurs de 30 po et de 36 po cm et 8 vis pour les largeurs supérieures). Fixer le Armoire bas de la hotte en installant les vis fournies avec les ancrages muraux (Figure 12). Figure 14 9. Raccordez les conduits à l’adaptateur de sortie et du clapet. Fixez en place en Bande de utilisant du ruban de gaine pour sceller tous les joints (Figure 15). montage Conduits en bois Clapet Adaptateur de Ancrages sortie muraux Hotte Hotte Figure 12 6. De l’intérieur du couvert de la hotte, fixez la hotte sur le dessous de l’armoire Figure 15 en utilisant quatre vis à bois (non-comprises) dans les trous en poire de la hotte (Figure 12).
  • Page 13 SECTION 12 SECTION 8 Maintenance Installation de la soufflante AVERTISSEMENT : 1. Référez-vous aux instructions incluses avec le ventilateur pour l’installation. VOUS ASSURER QUE L’ALIMENTATION EST COUPÉE AU PANNEAU DE SERVICE AVANT DE FAIRE L’ENTRETIEN SUR L’UNITÉ. SECTION 9 Filtres à graisse Installation de soffites optionnels les filtres à graisse compris avec votre hotte de cuisinière ont un dalot à graisse qui 1. Référez-vous aux instructions comprises avec le(s) soffite(s) spécifique(e) que devrait être lavé une fois par mois. Les filtres à graisse vont au lave-vaisselle et doivent vous avez choisi pour l’installation.
  • Page 14: Guide De Dépannage

    AN DE LA DATE DE L'ACHAT ORIGINAL OU JUSQU'À CE QUE L'ACHETEUR ORIGINAL DU PRODUIT VEND OU TRANSFÈRE LE PRODUIT, CELUI QUI SE PRODUIT EN PREMIER ET DANS AUCUN CAS AIR KING N’ASSUME AUCUNE RESPONSABILITÉ EXPRESSE OU TACITE POUR (I) DES DOMMAGES ACCIDENTELS OU INDIRECTS DE N’IMPORTE QUELLE CAUSE, OU (II) LE REPLACEMENT OU LA RÉPARATION DE TOUS FUSIBLES, DISJONCTEURS OU RÉCEPTACLES DE MAISON.
  • Page 15 TABLEAU DES PIÈCES DE RECHANGE - MODÈLES DE 18 PO Tous les modèles de 18 po # de pièce # Qté. Description de remplacement 1 1 Boîte de filage 5S1138002 2 1 Fil principal 5S1138003 3 1 Armoire – modèles de 30 po 5S1138630 1 Armoire – modèles de 36 po 5S1138640 4 1 Plateau à graisse - 30 po 5S1138230...
  • Page 16 TABLEAU DES PIÈCES DE RECHANGE - MODÈLES DE 10 PO Tous les modèles de 10 po # de pièce # Qté. Description de remplacement 2 1 Boîte de filage 5S1138002 3 1 Fil principal 5S1138003 4 1 Armoire – modèles de 30 po 5S1138030 1 Armoire – modèles de 36 po 5S1138040 5 1 Modèles de 30 po 5S1138130...

This manual is also suitable for:

Ap1030Ap1036Ap1830Ap1836

Table of Contents