Related Manuals for Jacuzzi Summer Rain 2 Wall and 3 Wall
Summary of Contents for Jacuzzi Summer Rain 2 Wall and 3 Wall
- Page 1 ™ SUMMER RAIN 2 WALL & 3 WALL WALK-IN SHOWER SYSTEMS INSTALLATION AND OPERATING INSTRUCTIONS...
-
Page 2: Important Safety Information
Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper installation related problems. -
Page 3: Table Of Contents
2 WALL Specifications _________________________________________________________________________ 2 Rough-in Reference ____________________________________________________________________ 3 Component Identification ________________________________________________________________ 4 Base Installation _______________________________________________________________________ 5-7 Tower and Glass Panels Installation ________________________________________________________ 8-12 3 WALL Specifications _________________________________________________________________________ 13 Rough-in Reference ____________________________________________________________________ 14 Component Identification ________________________________________________________________ 15 Base Installation _______________________________________________________________________ 16-18 Tower and Glass Panels Installation ________________________________________________________ 19-22 2 &... -
Page 4: Specifications
Should inspection reveal any damage or defect in any component, do not install the unit. Damage or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. -
Page 5: Rough-In Reference
2 WALL ROUGH-IN REFERENCE 84" FRONT VIEW 60" 33-3/4" 23" 21-1/2" 1/2" RIGID 27-15/16" COPPER PIPE UNDER BASE 42-5/16" TOP VIEW... -
Page 6: Component Identification
2 WALL COMPONENT IDENTIFICATION HEX WRENCH (1) STRAIGHT (PROVIDED) GLASS MOUNTING WALL POST MOUNTING WALL CAP (2) POST MOUNT BRACKET (2) BRACKET COVER (2) TAPE (6 PIECES) GLAZING GASKET (3) STRAIGHT GLASS PANEL TOWER WITH PLUMBING, FIXTURES, MAGNETIC GASKET, BOTTOM PLATE AND TOP COVER (PREASSEMBLED) TOWER... -
Page 7: Base Installation
PRELIMINARY ROUGH-IN The floor structure beneath the unit must be able to support a total weight of the unit and bather. Refer to the table under total weight. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. - Page 8 If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not respon- sible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility.
-
Page 9: Base Installation
Meguiar’s #10 Mirror Glaze. If not available, use auto- motive rubbing compound followed by an application of automotive paste wax. Major scratches and gouges which penetrate the acrylic surface require refinishing. Ask your Jacuzzi SILICONE Whirlpool Bath dealer for special instructions. SEALANT 1/4"... -
Page 10: Tower And Glass Panels Installation
2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 1 Position the wall posts so the edge of the post is set back 3/4" (19 mm) in from the edge of the base 3/4" (19 mm) EDGE OF BASE STEP 2 Level both wall posts in their proper position and mark where screw holes are to be drilled. - Page 11 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 4 Slide the glass panel into the wall post. Make sure that the corner notch is positioned toward the base of the tower. STEP 5 Place the tower onto base. Ensure the curved glass locates into the glazing channel.
- Page 12 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 9 Place the front rail and tower support rail against the walls. Check level and mark the position for the rail mounting bracket. The screw position will be above the rail.
- Page 13 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 13A Insert fixed glass support rail into panel post and tighten set screw. STEP 13B Drill a 1/8" pilot hole into tower support rail using the hole in the glass panel support rail. Screw M3.5X9.5 mm screw into hole.
- Page 14 2 WALL: TOWER, FIXED WALL AND CURVED GLASS INSTALLATION STEP 16 Turn on water supply and check for leaks. Correct any leaks before installing tower cover. STEP 17 Install tower cover as shown. Insert cover at top first. TOWER TOP PLATE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER...
-
Page 15: Specifications
Should inspection reveal any damage or defect in any component, do not install the unit. Damage or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. -
Page 16: Rough-In Reference
3 WALL ROUGH-IN REFERENCE 84" FRONT VIEW 60" 33-3/4" 23" 21-1/2" 1/2" RIGID 27-15/16" COPPER PIPE UNDER BASE 42-5/16" TOP VIEW... -
Page 17: Component Identification
3 WALL COMPONENT IDENTIFICATION HEX WRENCH (1) (PROVIDED) WALL TOWER MOUNT SUPPORT BRACKET (2) RAIL BRACKET COVER (2) TOWER COVER BASE TOWER WITH PLUMBING, FIXTURES, MAGNETIC GASKET, BOTTOM PLATE AND TOP COVER (PREASSEMBLED) FRONT RAIL CURVED GLASS GLAZING GASKET (2) TOWER MOUNTING BOLT &... -
Page 18: Base Installation
PRELIMINARY ROUGH-IN The floor structure beneath the unit must be able to support a total weight of the unit and bather. Refer to the table under total weight. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. - Page 19 If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not respon- sible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility.
- Page 20 If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath is not respon- sible for removal and/ or reinstallation costs. NOTE: Watertight installation of the drain is the installer’s responsibility.
-
Page 21: Tower And Glass Panels Installation
3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 1 Position the wall post so the edge of the post is set back 3/4" (19 mm) in from the finish wall. FINISH WALL STEP 2 Level the post in its proper position and mark where screw holes are to be drilled. - Page 22 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 5 Insert support rails into brackets in top moulding of tower but do not tighten at this time. TOWER SUPPORT RAIL STEP 6 Slide mounting bracket covers and mounting brackets onto front rail and tower support rail. RAIL MOUNTING BRACKET STEP 7...
- Page 23 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 9 Secure the rails. STEP 10 Tighten the tower base bolt. Two shut-off valves are provided. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw valve to stub outs at bottom of tower.
- Page 24 3 WALL: TOWER AND CURVED GLASS INSTALLATION STEP 13 Turn on water supply and check for leaks. Correct any leaks before installing tower cover. STEP 14 Install tower cover as shown. Insert cover at top first. TOWER TOP PLATE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER STEP 15...
-
Page 25: Operation
2 & 3 WALL OPERATION Shower Head There are four selectable positions: Jet, normal pulsating and aerated flow. Body Sprays (2 Upper & 2 Lower) To adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of the spray. Diverter Control To turn On water, turn the inner knob clockwise and adjust for more or less flow. -
Page 26: Maintenance
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. -
Page 27: Tower Fixture Repair Parts
TOWER FIXTURES REPAIR PARTS 1 (5X) 2 (5X) 3 (5X) TOWER ASSEMBLY 9 (5X) 11 (4X) 7 (Part of U547000) PART OF D709827 WASHER (PART OF D709827) 1. C546000 Lock Nut, 1/2" NPT WP (5X) 2. G559000 Ring Compression SS (5X) 3. -
Page 28: Tower Plumbing Repair Parts
TOWER PLUMBING REPAIR PARTS 1. A944000 (9X) Spring Clamp, .625 OD Hose 2. U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb 3. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb 4. A945000 (7X) Spring Clip, .75 OD Hose 5. U400000 FTG, Straight, 1/2" FTS X 10mm Barb 6. -
Page 29: Wall Unit Repair Parts
5 (2X) 6 (2X) 7 (6X) U134827 Rail Back Walk-in U133827 Rail 2 Wall Walk-in U245827 Rail Assembly Walk-in U149000 Bracket, Mounting Rail U119827 Wall Post, Panel U138827 Cap, Wall Post J686000 Tape High Bond, 2 Sided U159000 Gasket,Vinyl, Glass Panel U479XXX Glass Panel Assembly, Walk-in 10. -
Page 30: Wall Unit Repair Parts
U134827 Rail Back Walk-in 3 Wall U245827 Rail Assembly Walk-in 3 Wall U149000 Bracket, Mounting Rail U119827 Wall Post, Panel U138827 Cap, Wall Post U124XXX Tower Cover U257XXX Final Shell, Tower, Walk-in 3-Wall U126XXX Tower Body Walk-in U136XXX Cap, Top Tower U137XXX Cap, Bottom, Tower U149000 Bracket, Mounting Rail U354000 Screw, Self Tap,#8-1.25"... -
Page 31: Warranty
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished by the Company. - Page 32 The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period;...