Table of Contents
Advertisement
CENTER PANEL MAINTENANCE
The hand held shower head is equipped with a screen
which must be occasionally cleaned of limestone and
other deposits.
The screen is placed between the
flexible hose and the shower head. If limestone deposits
are on the jet nozzles, the shape of the water jets may be
altered. Remove and clean the nozzles occasionally.
Forcefully turn the nozzle counterclockwise until a click
is felt. Then remove the nozzle and clean it by soaking
it in a moderate vinegar and water solution. Do not use
metal tools (such as scissors or screwdrivers, etc.) to
clean the nozzle. For routine cleaning of plastic surfaces
use a mild liquid detergent only. Do not use abrasive
cleaners, alcohol, or other solvents. Any normal polish
can be used to keep acrylic surfaces shiny. The glass
panels can be cleaned with any glass-cleaning product
available on the market. Do not use abrasives, sol-
vents, or acetone on any part of the J-Allure.
Important (For units with TV): These units are equipped
with a fan mounted inside the TV housing. At least every
2 years have a service technician verify that the fan is
operational. If the fan is not operating properly discon-
tinue TV use until fan can be repaired or replaced.
BATH MAINTENANCE
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the
gloss to a dulled acrylic surface by applying Meguiar's
#10 Mirror Glaze, a product specifically designed for use
on acrylic finishes. If Meguiar's is not available, an
acrylic polish of equal quality or automotive paste wax is
acceptable. Never use abrasive household cleaners
on any Jacuzzi Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry
sandpaper. Restore the gloss using Meguiar's Mirror
Glaze or automotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirl-
pool Bath dealer for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE
PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the
whirlpool system, it is recommended that a whirlpool
bath be purged at least twice a month. For best results,
however, we recommend that you purge your whirlpool
bath after each use using our exclusive two-part plum-
bing system cleaner made specifically for whirlpool
baths. Systems Clean ™ is available through an autho-
rized Jacuzzi Whirlpool Bath Distributor or by calling us
direct at 1-800-288-4002. Instructions for use: Imme-
diately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add hot water, if necessary,
so the water is at least 2" above the highest jet. Turn on
the unit without the aerator. Pour the contents of the
Systems Clean Packet 1 (taking care not to get the
material on yourself) into the bath near the intake for the
circulation pump. Repeat same process with Systems
Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor. Run the bath for 5 to
10 minutes. Drain completely and rinse any residue.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath
residue and desire an alternative cleaning mechanism,
we recommend SUPER SYSTEMS CLEAN PLUS manu-
factured by Stearns Packaging to rectify this condition.
This may be obtained by contacting us at l-800-288-
4002. It is recommended that you follow the instructions
provided by the manufacturer with the product. Re-
peated use may be necessary. SUPER SYSTEMS
CLEAN PLUS does not replace the necessity to regu-
larly purge your whirlpool system with Systems Clean as
recommended.
(For additional information about water content, contact
us for a copy of the Jacuzzi Water Quality Primer)
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH
ADDITIVES.
If you want to use any kind of bath additive, use only a
small amount of low-foaming powder or crystal sub-
stance; the whirlpool action intensifies the foaming prop-
erties of soaps.
The use of certain bath oils, bubble baths and bath
additives may increase the level of accumulations of
bath residue in the whirlpool system. If excess accumu-
lations persist, you should discontinue use of these
products.
24
- Quick Links:
- Maintenance
Hide quick links:
Advertisement
Table of Contents
