Related Manuals for Jacuzzi J-ALLURE J-ALLURELuxury Bathing and Entertainment System
Summary of Contents for Jacuzzi J-ALLURE J-ALLURELuxury Bathing and Entertainment System
- Page 1 ™ J-ALLURE Luxury Bathing and Entertainment System Installation & Operation Instructions WHIRLPOOL BATH...
-
Page 2: Important Safety Information
Note: This is a professional grade product. A good knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper installation related problems. -
Page 3: Table Of Contents
Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. -
Page 4: Specifications
J-Allure Specifications FLOOR DIMENSIONS MOTOR/PUMP LOADING 54" (1372 mm) L 115 VAC 60 Hz 74 lb/sq. ft. 54" (1372 mm) W 10 Amp (459 kg/sq. m) 92-1/2" (2350 mm) H 3450 RPM Single phase 83-3/8" PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. REQUIRED OPERATING WATER... -
Page 5: Hardware
J-Allure HARDWARE SKIRT SCREW, DRYWALL #8x 2, Quantity 4 SCREW, SHEETMETAL #6x 1/2, Quantity 15 SCREW COVER Quantity 4 CENETER PANEL HEX NUT, Quantity 6 SCREW, M3.5X9.5, Quantity 6 WALL ANCHOR, Quantity 4 FLAT WASHER, Quantity 6 SCREW, M4.2X19, Quantity 6 SCREW, #8x 1, Quantity 4 GLASS ASSEMBLY SCREW, M3.5X9.5, Quantity 4... -
Page 6: Framing And Support
J-Allure Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of approximately 94 lb/sq. ft. (bath, water, and bather). -
Page 7: Rough-In Reference
J-Allure Rough-in The installation requires three cutouts in the walls. Two cutouts allow room for the speakers. The third cutout is necessary to route water supply piping to the center panel, and to route hoses for the steam generators to the bath. The location of a 230VAC power outlet is indicated on the wall cutouts illustration. - Page 8 J-Allure Finished Walls Before fixing the bath in place, make sure the finished walls above the rim of the bath are perpendicular. The two wall extrusions at the edges of the fixed panels will allow some compensation for walls out of true less than 3/16". (See fixed panels installation for wall extrusions.) If that is the case, the bath may be placed against the finished walls.
-
Page 9: Electrical
J-Allure 9" MIN. CUTOUT IN WALL 81" FINISHED WALL 4" MIN. ELECTRICAL OUTLET (115 V) FOR BATH Wall Cutouts 38" 38" STUD FOR PLUMBING 12" MIN. 7" STUD DETAIL 1 75-1/2" 23-1/4" FINISHED 1x4 (NOT FOR SUPPORT) FLOOR BATH DO NOT BRIDGE PERIMETER CENTER PANEL CUTOUT Suggested Rough-in... -
Page 10: Skirt Installation And Service Access
J-Allure Skirt Installation It is necessary to mount the skirt shell clips on the factory installed wood blocks located along the underside of the rim. Mark hole locations on the blocks using clips as a template for correct hole spacing. Then drill a pilot hole 1/2" deep using a 3/32"... -
Page 11: Drain Information And Plumbing
A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste flange, strainer, overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish. -
Page 12: Water Supply
#10 Mirror Glaze. If that is not available, use automotive rubbing compound followed by an application of automotive paste wax. Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions. -
Page 13: Center Panel Installation
J-Allure Center Panel Installation Connect the fixed male end of the flexible supply lines to the female supply connections in the wall cutout. Position the center panel frame in the corner of the bath with the mounting tabs between the edge of the bath and wall. To open the service door, remove the screw cover below the mixer handle and unscrew the exposed screw. - Page 14 J-Allure Center Panel Installation Connect the ends of the flexible supply lines with adaptors to the hot and cold connections of the mixer. The steam lines are to be routed in such a way that they travel up from the steam generators and down to the steam heads.
-
Page 15: Tv Installation (For Units With Tv)
J-Allure TV Installation (Units with TV) Remove drip shield. Connect power cord, audio cable antenna/cable TV. Hook up fan power lines with red to red and black to black wires. Tighten cable tie and cut off excess. Tighten cable tie with anchor (not supplied) to the TV power cord. -
Page 16: Fixed Glass Panels Installation
J-Allure Fixed Panels Installation Locate the guide with the gasket. This is the lower guide. Remove this gasket and install on the top guide. Position the lower guide on the two fixed panels while they are resting on the floor in an upside down position. Align the predrilled holes in the guide and panels and screw together with screws and spacers (3.5x45mm self-threading). - Page 17 J-Allure Fixed Panels Installation Install the two wall extrusions on the ends of the fixed panel assembly. Make sure they are flush against each fixed panel. Where the fixed panel assembly will rest on the bath rim, apply sealant. Position the fixed panel assembly on the bath by inserting the pin into its seat on the lower guide.
-
Page 18: Side Wall Installation
J-Allure Side Walls Installation Lift one of the side walls through the open doors. Reach under the bath rim and pull up the speaker wires. Hook up these wires observing the polarity as directed from the CD player manual. Then insert the 3 bolts into the slotted holes in the center panel frame. -
Page 19: Caulking
J-Allure Side Walls Caulking After the side walls are installed, they must be caulked with silicone sealant (not provided). Seal the entire length at the bottom and from the bottom to top where the side wall moulding meets the attached extrusion. Also caulk the joint between the side wall extrusion and the fixed panel frame. - Page 20 J-Allure Inside Caulking Caulk the joint between the lower guide and the bath. FIXED PANELS LOWER GUIDE SEALANT...
-
Page 21: Sliding Doors Installation
J-Allure Sliding Doors Installation Take one of the doors inside the shower compartment. The upper rollers will be fixed while the bottom rollers will be loose. In a vertical position, insert the upper and lower rollers (at the same time) into the roller insertion point located at the center of the upper and lower guide. -
Page 22: Dome Installation
J-Allure Dome Installation Apply gasket to dome as shown below. Note: there is no gasket on the dome where it rests on the upper guide. Then carefully lift the dome and place onto the corner panel , side walls and upper guide. Bring the edge of the dome in contact with the front part of the upper guide. - Page 23 OPERATING INSTRUCTIONS CENTER PANEL System control is provided by the electronic display located on the center panel. The display is used to start up the five functions of the unit: the hand held shower, the fixed shower, the hydromassage (all jets), hydromassage (pulsed jets), and the steam bath. The display is composed of clear symbols to identify the five functions.
-
Page 24: Operation
If your bath has an optional Jacuzzi Whirlpool Bath wall mounted timer, set it for the amount of time you wish the whirlpool to operate. Note: when you desire less than 10 minutes of whirlpool action, it is necessary to turn the timer knob clockwise past the number 10 and then back to the desired amount. - Page 25 Note: The remote for the CD/radio is not intended to be used inside the shower or in the bath. Note: For units with AM/FM radios, the quality of AM reception will vary by locality. Jacuzzi Whirlpool Bath is not responsible for the quality of AM reception.
-
Page 26: Maintenance
CLEAN PLUS does not replace the necessity to regu- larly purge your whirlpool system with Systems Clean as recommended. (For additional information about water content, contact us for a copy of the Jacuzzi Water Quality Primer) Bath Additives NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES. - Page 27 Suction Cover/Strainer Maintenance Clean the suction cover/strainer of hair and debris when necessary. To do this, remove the center screw and detach the square cover. Clean the cover by backflush- ing debris from the holes. Replace the suction cover immediately after cleaning. When reinstalling, orient the cover/strainer with the small notch at the bottom.
- Page 28 CARE AND MAINTENANCE OF STEAMPRO STEAM GENERATORS Maintenance of the Steampros includes flushing periodically and visually inspecting for water leaks. To drain the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPro units, open the center panel door. To do so, open the screw cover and remove the screw.
- Page 29 Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
-
Page 31: Warranty
All implied warranties of merchantability and fitness for a particular purpose are equal in duration with the express warranties set forth herein. NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. -
Page 32: Warranty
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period;...