FLORABEST FSG 85 B1 Operation Manual

FLORABEST FSG 85 B1 Operation Manual

Chain sharpener

Advertisement

FSG 85 B1
®
Chain Sharpener
Translation of original operation manual
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FSG 85 B1 and is the answer not in the manual?

Questions and answers

Summary of Contents for FLORABEST FSG 85 B1

  • Page 1 FSG 85 B1 ® Chain Sharpener Translation of original operation manual...
  • Page 2 Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. GB / IE Translation of original operation manual Page...
  • Page 4  14a 14b ‚ ƒ...
  • Page 5: Table Of Contents

    Content Safety Instructions Safety Instructions ........5 This section concerns the basic safety Safety instructions / symbols on the regulations for working with the electric equipment ...........5 chain sharpener. Symbols in the manual ......6 Safety instructions / symbols General safety instructions ....6 on the equipment Further Safety Instructions ....7 General description .......8...
  • Page 6: Symbols In The Manual

    Symbols in the manual flammable liquids or gases. Guard against electric shock. • Warning symbols with informa- Avoid body contact with earthed or tion on damage and injury pre- grounded surfaces (e.g. pipes, radia- tors, ranges, refrigerators). vention. • Keep other persons away. Instruction symbols (the instruction Do not let persons, especially chil- dren, not involved in the work touch...
  • Page 7: Further Safety Instructions

    from the socket. Keep the cord away - Before further use of tool, it should be carefully checked to determine from heat, oil and sham edges. • Secure work. that it will operate properly and per- Where possible use clamps or a vice form its intended function.
  • Page 8: General Description

    General description saw chain. In the event that it is dam- aged or severed, immediately discon- nect the plug from the socket. The diagrams can be found on Do not touch the cable before it has the front flap. been disconnected from the mains. Summary •...
  • Page 9: Function Description

    Function description • Chain sharpener with grinding disk installed Prior to first starting the appliance, firmly • Handle mount it on a worktop. It is driven by an • Chain clamping unit and locking screw electric motor with protection against •...
  • Page 10: Working With The Equipment

    (24) from the package to attach the grinding plinth to the worktop. Risk of injury! Wear ear, eye and hand protection! Assembling the grinder: 5. Screw the handle (4) into the grinding head (2). When working with the saw chain, 6.
  • Page 11: Sharpening The Saw Chain

    Test run: Inserting the saw chain: Before starting work and after each 1. To open the chain guide, turn the change of grinding disk, carry out a test clamping lever (13) anticlockwise. You run of at least 30 seconds with no load. must first return the clamping lever to Switch off the equipment immediately if its home position several times.
  • Page 12: Maintenance And Cleaning

    Maintenance and cleaning Sharpen: 9. Switch on the equipment (see “switch- ing on and off “). Disconnect the plug before adjust- 10. By putting gentle pressure on the ment, maintenance or repair. handle (4), move the grinding head (2) upwards and sharpen the cutting Have any work not described in tooth.
  • Page 13: Storage

    Storage Ensure that the disk dimensions fit the equipment. • Use only fault-free grinding disks • Store the appliance in a dry place well (ring test). out of reach of children. • If the locator hole in a grinding disk is too small, do not subsequently Grinding disks must be stored redrill in order to increase the size.
  • Page 14: Technical Specifications

    Certain com- ponents are subject to normal wear and tear and are excluded from the Chain sharpener ....FSG 85 B1 guarantee. These include in particular: Nominal input voltage .....230V~, 50 Hz Grinding disks, carbon brushes, stop- Power consumption ..85 W (S2:15 min)**...
  • Page 15: Replacement Parts

    on estimated exposure under actual usage conditions (all parts of the operating cycle are to be considered, including, for example, times during which the power tool is turned off and times when the tool is turned on but is running idle). Technical and optical changes may be undertaken in the course of further de- velopment without notice.
  • Page 16: Translation Of The Original Ec Declaration Of Conformity

    Translation of the original EC declaration of conformity We hereby confirm that the FSG 85 B1 series Chain sharpener (serial number 201105000001 - 201105101800) conforms with the following applicable relevant version of the EU guidelines: 2006/42/EC • 2004/108/EC In order to guarantee consistency, the following harmonised standards as well as na- tional standards and stipulations have been applied: EN 61029-2-10:2010 •...
  • Page 17: Exploded Drawing

    Exploded Drawing 2011-05-10-rev02-gs...
  • Page 18 IAN 63966 Grizzly Gartengeräte GmbH & Co. KG Am Gewerbepark 2 D-64823 Groß-Umstadt Last Information Update: 03 / 2011 Ident.-No.: 75019720032011 - 6...

Table of Contents

Save PDF