Fastening The Dishwasher To The Cabinet - Viking Undercounter Dishwashers Installation Manual

FASTENING THE DISHWASHER TO THE CABINET

WARNING!
The dishwasher door will not stay open by itself until the door panel is installed. Be aware of this when fastening
the dishwasher to the cabinet.
Fasten the dishwasher to a kitchen cabinet using the 1" (2.5 cm) screws provided.
NOTE: It is necessary to secure the dishwasher with screws so that it does not tilt if something heavy is placed on the
door.
1. Using the screws and spacers, fasten the dishwasher to the cabinet through holes A.
2. Plug holes A with plastic plugs provided.
3. When the machine is properly fastened, check that the feet are tight against the floor and the machine is level.
installing the kickplate
First, replace the guard plate and toe kick brackets (see page 8). Adjust the bracket depth to allow for the thickness of
the kickplate. First, pull or push the bracket to the required depth, less the thickness of the kickplate. Then, push the
gray tab towards the outside edge of the unit until it locks the bracket into place.
Once the toe kick brackets are in place, install the kickplate as follows:
1. Remove kickplate and felt insulation from the packaging.
2. Peel the adhesive protection strip off the insulation and press it firmly to the back side of the kickplate, making sure
not to cover any slots on the kickplate.
3. Fit the kickplate over the toe kick brackets so that the kickplate is held securely in place. Adjust the kickplate in a
way that it maintains contact with the floor.
12
INSTALLING THE DESIGNER SERIES OR PROFESSIONAL SERIES DOOR PANEL
(Purchased separately)
The unit comes with everything needed to make installing the door panel easy.
1. Peel the adhesive backing off the washers and place
them in line with the four holes (F) on the metal inner
door of the dishwasher.
2. Loosen the screws (D) on the outer edge of the
dishwasher.
3. Pull the fan exhaust frame (E) down until the lower
edge aligns withthe lower edge of the cabinets and
tighten the screws (D).
W W A A R R N N I I N N G G ! ! ! ! T T h h e e d d o o o o r r p p a a n n e e l l m m u u s s t t n n o o t t o o b b s s t t r r u u c c t t t t h h e e
f f a a n n e e x x h h a a u u s s t t v v e e n n t t . .
4. Hook the door panel screws into the keyholes (C) on
the dishwasher door and pull up on the panel.
5. While holding the door panel into position, carefully
open the dishwasher door. Using the stainless steel
screws provided, fasten the door panel into the four
holes (F) on the inner door.
6. Remove the backing from the protective tape and
apply it to the edge of the panel, in front of the
exhaust vent.
7. Raise the exhaust frame (E) to the bottom edge of
the door panel and tighten screws (D) on the side of
the dishwasher.
N N O O T T E E : : Door shown is the Designer Series door panel.
INSTALLING THE FULL OVERLAY CUSTOM DOOR FRONT
The dishwasher can be installed with a
custom door panel that extends from the
kickplate to the countertop. The unit
comes with everything needed to make
installing the door panel easy. The inner
door is pre-drilled for the custom door's
mounting screws. The custom panel
should be at least 3/4" (1.9 cm) thick.
ITEMS PROVIDED WITH THE UNIT
(2) 3/8" (.95 cm) screws (B)
(4) 1 3/4" (4.4 cm) screws (F)
CUSTOM OVERLAY DIMENSIONS
3 3 / / 4 4 " "
Width 23 1/2" (59.7 cm)
( ( 1 1 . . 9 9 c c m m ) )
Height 29 3/4" (75.6 cm)
Thickness 3/4" (1.9 cm)
Weight Up to 22 lbs. (9.9 kg)
3 3 / / 4 4 " " T T h h i i c c k k
( ( 1 1 . . 9 9 c c m m ) )
(Locally supplied)
2 2 3 3 1 1 / / 2 2 " "
( ( 5 5 9 9 . . 7 7 c c m m ) )
1 1 4 4 1 1 3 3 / / 1 1 6 6 " "
( ( 3 3 7 7 . . 6 6 c c m m ) )
2 2 9 9 3 3 / / 4 4 " "
( ( 7 7 5 5 . . 6 6 c c m m ) )
2 2 2 2 . . 0 0 " "
( ( 5 5 5 5 . . 9 9 c c m m ) )
C C u u s s t t o o m m D D o o o o r r
R R e e a a r r V V i i e e w w
13
3 3 / / 4 4 " " T T h h i i c c k k
( ( 1 1 . . 9 9 c c m m ) )
C C u u s s t t o o m m D D o o o o r r
R R e e a a r r V V i i e e w w