Viking DFUD042 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Viking Manuals
  4. Dishwasher
  5. Custom Front DFUD042
  6. Installation instructions manual

Viking DFUD042 Installation Instructions Manual

Undercounter dishwashers
Hide thumbs Also See for DFUD042:
Table of Contents

Advertisement

Quick Links

See also: Use and Care Manual , Manual
INSTALLATION
INSTRUCTIONS
UNDERCOUNTER DISHWASHERS
IMPORTANT - PLEASE READ AND FOLLOW
•Before beginning - please read these instructions completely and carefully
•Do not remove permanently affixed labels, warnings, or rating plates from the dishwasher. This may void warranty.
•Please observe all national and local codes.
•Please ensure that this product is properly grounded.
•The installer should leave these instructions with the consumer who should retain for local inspector's use and
for future reference.
Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage,
hertz, wattage, amps, and phase is attached to the product. Wiring the dishwasher with more voltage than
it is rated for may cause severe damage to the thermistor, element, and other components. Wiring the
dishwasher with less voltage than it is rated for may cause significant decrease in performance. To reduce
the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by
qualified people in accordance with all applicable codes and standards, including fire-rated conditions.
Electrical power must be turned off at circuit breaker or fuse box before connecting any electrical cables.
SEQUENCE OF DISHWASHER INSTALLATION
1. Prepare the location
2. Prepare the water supply
3. Prepare the drain
4. Prepare the electrical supply
5. Adjust the feet
6. Push the dishwasher into place
7. Connect water supply
8. Connect drain supply
9. Connect electricity
10. Fasten the dishwasher
11. Install the kickplate
12. Install the door
INTRODUCTION
Read these instructions carefully and completely before installing the dishwasher. The installation should be carried out
by a qualified person, who is familiar with all local codes and ordinances for electrical and plumbing connections. If the
dishwasher is being installed for the first time, most of the work has to be done before you move it into place. If you
are replacing an old dishwasher, you must check the old connections.
NOTE: The drain hose is fastened to the back of the machine at the best high loop height.
To eliminate potential drain problems, leave this hose in place.
WARNING!
WARNING!
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200

Advertisement

Table of Contents
loading

Related Manuals for Viking DFUD042

Summary of Contents for Viking DFUD042

  • Page 1 If the dishwasher is being installed for the first time, most of the work has to be done before you move it into place. If you are replacing an old dishwasher, you must check the old connections.

  • Page 2: Tools You Will Need

    TOOLS YOU WILL NEED 1) Phillips No. 2 screwdriver 2) Flat blade screwdriver 3) Torx screwdriver size T 20 4) Adjustable wrenches (if copper fittings are used) 5) Open ended wrenches 1/2” (1.3 cm) or 5/8” (1.6 cm) 6) Wire cutters and strippers 7) Tape measure 8) Level 9) Electric Drill...

  • Page 3: Cycle Data

    •PEX tubing with 3/8” (.95 cm) compression fitting supplied with unit. BASIC DRAIN DATA •6’6” (2.0m) 3/4” (1.9 cm) ID “crimp-proof” rubber drain hose with clamp attached to dishwasher; can be extended up to a maximum of 10 feet (3.0m) with 3/4” (1.9 cm) ID copper tubing.

  • Page 4: Cutout Dimensions

    CUTOUT DIMENSIONS NOTE: If the dishwasher is installed in a corner, there must be a minimum clearance of 2” (5.1 cm) from the side wall so the door can open. BASIC SPECIFICATIONS DESCRIPTION Overall Width* Overall Height from floor** Overall Depth from Rear...

  • Page 5: Basic Dimensions

    BASIC DIMENSIONS 2” (5.1 cm) 7” - 9-3/4” (17.8 cm - 24.8 cm)) 3-1/2” - 6-1/4” (8.9 cm - 15.9 cm)) 24” (61.0 cm) 34-1/8” - 36-7/8” (86.7 cm - 93.7 cm) *with side trim 23 7/8”* (60.6 cm) 1-1/2” - 4-7/8” (3.8 cm - 12.9 cm) Adjust Toe Kick...

  • Page 6: Water Supply

    Plumbing connections must comply with applicable sanitary, safety and plumbing codes. Water pressure for the water supply should be minimum 18 to 176 psi. The dishwasher is supplied with a 6’ (1.8 m) PEX water supply line that has s 3/8”...
  • Page 7 DRAIN A rubber drain hose (7/8” [2.2 cm]) is provided with the dishwasher which is connected to the back of the unit to form a high loop. The access hole for the drain line should be 1 1/2” (3.8 cm) at a minimum of 20” (50.8 cm) from the floor. If the hose provided is not long enough, extend it with a 7/8”...

  • Page 8: Electrical Connections

    Disconnect the electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. The dishwasher comes with a 6’ (1.8 cm) electrical cord for 110-120 volts, 15/20 amp supply. This cord should be plugged into the 110-120 volt outlet located under the sink.

  • Page 9: Connecting The Electrical Cables

    Testing for Leaks •Turn on the water supply and check for leaks. •Turn the power on at breaker/fuse box and test the dishwasher operation by running a Rinse cycle. (This should take about four minutes.) •Turn off the electrical power and check for leaks under the dishwasher.

  • Page 10: Adjusting Side/Top Trim

    To adjust: Open the dishwasher door and remove the screws that attach the side and top trim to the dishwasher. Adjust the side and top trim to the desired hole setting in the side and top trim and replace screws. Be sure to attach the side and top trim from inside the dishwasher.

  • Page 11: Fastening The Dishwasher To The Cabinet

    Fasten the dishwasher to a kitchen cabinet using the 1” (2.5 cm) screws provided. NOTE: It is necessary to secure the dishwasher with screws so that it does not tilt if something heavy is placed on the door.

  • Page 12: Installing Designer/Professional Series Door Panel

    4. Hook the door panel screws into the keyholes (C) on the dishwasher door and pull up on the panel. 5. While holding the door panel into position, carefully open the dishwasher door. Using the stainless steel screws provided, fasten the door panel into the four holes (F) on the inner door.

  • Page 13: Adjusting The Door Springs

    Before fitting the custom door front, the dishwasher must be installed underneath the cabinet. After making required measurements, it may be necessary to pull the unit out again to install the door front. 1. Fit handle (A) onto the panel according to the manufacturer’s instructions (NOTE: A handle should be used rather than a knob, because a knob does not provide enough grip.)

  • Page 14: Wiring Diagram

    VIKING RANGE CORPORATION 111 Front Street • Greenwood, Mississippi 38930 USA • (662) 455-1200 Specifications subject to change without notice F20244C (PS0306VR) #8078394...

This manual is also suitable for:

Dfud142

Table of Contents