Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Viking DFUD040
Summary of Contents for Viking DFUD040
- Page 2 VIKING RANGE CORPORATION, P. O. DRAWER 956, GREENWOOD, MS.38930 USA...
-
Page 3: Table Of Contents
Table of Contents Index---------------------------------------------------------------------------------------------- 2 DFUD Serial Rating Plate--------------------------------------------------------------------- DFUD 042/142 Control Panel Graphics----------------------------------------------------- 3 DFUD 040/140 Control Panel Graphics----------------------------------------------------- 4 DFUD 040/140 Wash Cycle Options-------------------------------------------------------- DFUD 040/140 Cycle Data------------------------------------------------------------------- DFUD 042/142 Wash Cycle Options-------------------------------------------------------- DFUD 042/142 Cycle Data-------------------------------------------------------------------- 8 INSTALLATION Water Supply--------------------------------------------------------------------------- 9 Electrical Connections----------------------------------------------------------------... -
Page 4: Dfud Serial Rating Plate
The serial rating plate is located on the right hand side of the inner part of the door. Serial numbers are located in the lower right corner of the rating plate and give you the year and week of manufacture. Use complete serial number when referring for service. The buttons are on the top side of the control unit. -
Page 5: Dfud 040/140 Control Panel Graphics
CONTROL PANELS DISHWASHER FEATURES... -
Page 6: Dfud 040/140 Wash Cycle Options
WASH / CYCLE OPTIONS DFUD040 – DFUD140 CHANGING A PROGRAM AFTER THE UNIT HAS STARTED The dishwasher is programmed to stop operating if the door is opened during a cycle. If you want to change a program or option after starting the machine, open the door slightly to let the spray arms stop rotating and avoid getting sprayed with water. -
Page 7: Dfud 040/140 Cycle Data
Using the lower water temperature setting. Using the higher water temperature setting. NOTE: Does not include time for dry/heated dry Econo option available for Pots, Normal, and China cycles on DFUD140 only. • Reduces temperature of main wash to 120º F (50º C) •... -
Page 8: Dfud 042/142 Wash Cycle Options
DFUD042 / DFUD142 CHANGING A PROGRAM AFTER THE UNIT HAS STARTED The dishwasher is programmed to stop operating if the door is opened during a cycle. If you want to change a program or option after starting the machine, open the door slightly to let the spray arms stop rotating and avoid getting sprayed with water. -
Page 9: Dfud 042/142 Cycle Data
Using the lower water temperature setting. Using the higher water temperature setting. NOTE: Includes time for dry... -
Page 10: Installation
INSTALLATION WATER SUPPLY: Water pressure for the water supply should be minimum 18 to 176 psi. The water inlet valve is on the right rear of the machine. The dishwasher should preferably be connected to a hot water supply (2). If cold water supply is used, the washing times will be longer. -
Page 11: Drain Options
DRAIN: A drain hose is provided with the dishwasher which is connected to the back of the unit to form a high loop. The access hole for the drain line should be at a minimum of 20” from the flood. If the hose provided is not long enough, extend it with a 7/8”... -
Page 12: Toe Kick/Guard Plate
REMOVING THE TOE KICK BRACKETS AND GUARD PLATE: (This only necessary if a hardware installation kit was used.) To remove the toe kick brackets, pull the gray tabs towards the middle of the dishwasher. Then, pull straight out on the brackets. -
Page 13: Dfud 040 Fault Tracing
DFUD040 Fault Testing: 3) Press NORMAL once to increase 1) Press the RINSE cycle button five fill time be fifteen seconds. times within 15 seconds to enter the 4) Press CHINA once to increase fill component test mode. time by thirty seconds. -
Page 14: Dfud 140 Fault Tracing
(and Fan/Vax motor VUD040) increase (150 sec.) 7) Press Delay (8) to start Fan/Vax Motor 6) Press Delay (8) to get 200% increase (not DFUD040) (180 sec.) Press Start/ Stop to exit Fault Mode. Protected Start Program: Press Rinse and Hold (5) five times and then:... -
Page 15: Dfud 140 Indication Lamps
THE INDICATING LAMPS DFUD140... -
Page 16: Dfud 041 Program Sequence
DFUD040/140 Illustrated below is a normal program and the sequence in which the various components are connected. NORMAL WASH Component Comments Outlet pump 25 seconds RINSE/HOLD Inlet valve 540 pulse* 0.7 gal Circulation pump 30 sec High pressure upper arm**... - Page 17 CLEANING STEP Inlet valve 140 pulse* 0.2 gal Circulation pump 20 sec Low pressure lower arm Outlet Pump 25 sec FIRST RINSE Inlet valve` 540 pulse* 0.7 gal Circulation pump 240 sec Circulation pump 60 sec High pressure upper arm Outlet pump 2 sec SCS stage...
-
Page 18: Dfud 042/142 Fault Tracing
1) Press program button Drying Selection: (LED lights when long drying is selected). repeatedly until the desired model is Long and Normal drying (Quick wash; selected. Long and Short drying.) L1 lit: Model without Super rinse option (S7) Washing in both Baskets: L2 lit: Model without Super rinse Both baskets washing (basic setting). - Page 19 Child lock: (DFUD142 only) SERVICE MENU: Activation of setting menu: 1. Turn off main switch Turn off the main switch 2. Wait for at least 5 seconds Wait for at least 5 seconds 3. keep the Program and Start buttons Keep the Temperature and Drying depressed (S1 &...
-
Page 20: Poor Dishwashing Results
POOR DISHWASHING RESULTS Try the following remedies. Poor results may not always be caused be the dishwasher. Read through the chart below before contacting your servicer. PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Spotting and filming Hard water Use the maximum recommended amount (3 tablespoons of dish- washer detergent. - Page 21 PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Change the dishwasher detergent if the results is still unsatisfactory Items not loaded properly Check that you loaded the items according to the instructions in the owners guide. Do not overload. Make sure water can reach all soiled surfaces.
- Page 22 PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Low water pressure Check that the water valve is fully open. Make sure that the water pressure is between 18 and 176psi. Improper loading of dishes Load dishes to prevent water and detergent from being trapped in or between items.
- Page 23 PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Distortion of plastics Plastic item has low heat Plastics vary in their ability to tolerance tolerate heat. Check washing instructions for all plastic items to be sure they are dishwasher safe. If they are, place in upper rack away from the heating element.
- Page 24 PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Plastic items. Certain plastic materials difficult to dry. Plastics may need towel drying. Improper loading or Do not overload or nest items. Be unloading sure all surfaces drain well. Load items with concave bases so as much water as possible can run off.
- Page 25 PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY Dishwasher will not start. Check service notes Dishwasher will not Check service notes. drain Water backs up in Food waste disposer Check disposer and trap at sink for sink when dishwasher and trap. blockage or food particles. drains.
-
Page 26: Troubleshooting Guide
TROUBLESHOOTING: If you have answered “YES” to the If there are problems with poor washing above questions, and if the machine results, you must observe the following appears to be without a power supply, rules in the first instance: you should first check that a power supply is present as far as the main •... - Page 27 • Is • Inlet valve fine filter securely • Float attached? • Are you using the correct wash • Micro switch program? • Is the machine correctly loaded? FAULT CODES In the fault codes below, “L” denotes If you have answered “YES” to the LED and “F”...
- Page 28 CHECK: CHECK: • Thermister • Filter • Control unit • Sump (pressure chamber) • Pressure sensor. L4 / F4 Water intake fault <80 pulses within 60 seconds or correct L1 + L4 / F9 Circulation fault number of pulses is not achieved with The pressure sensor senses excessively 255 seconds.
-
Page 30: Dfud 140 Cycle Sequence Chart
DESIGNER SERIES DFUD 140 CYCLE SEQUENCE CHART Geographical location of switches on the keyboard. (Some switches are not displayed on some models.) INLET TIME Press 5 Five Times to Enter Program Mode. Press 3 to get Normal Inlet Time (Default) Press 4 to get 25% increase Press 5 to get 50% increase Press 6 to get 100% increase... - Page 34 COMPONENTS AND MEASURED VALUES: Indicated resistance values apply at room temperature Values within ± 10% are regarded as normal. Radio interference suppression filter 680K ohm Heating element 1400W 120V 12 ohm Heating element 1200W 120V 10 ohm Thermistor 25K ohm Combined dispenser 120V 0.3K ohm Circulation pump 120V...