Blower Operation - Jøtul GI 450 DV Katahdin Installation And Operation Instructions Manual

Figure 17. Completed log set assembly.
4. Place the front log on the single log pin so that the left
end of the log rests on the log support and the and-
iron holder- directly above the air shutter.
5. Place the cross-over log on the two remaining pins-
top right to the rear log, bottom left on the front log.
See fig. 17.
6. Install the embers: the insert is shipped with a pack-
age of ember stones. Spread them evenly across the
burner tube screen. It is best to equally space these
embers for optimum flame appearance. NOTE: YOU
DO NOT NEED TO USE ALL OF THE EMBER STONES.
7. Replace the andiron set, center in the firebox over the
andiron support.
THE CERAMIC FIBER LOGS AND EMBER STONES CAN
IRRITATE YOUR SKIN. IF THIS HAPPENS, GENTLY WASH
HANDS WITH WARM, SOAPY WATER.
16

Blower Operation

The GI 450 DV Katahdin is equipped with a 125 cfm heat-
activated blower. A ten foot power cord is installed in
the rear of the valve compartment under the firebox.
Open the Lower Grill and fully unwrap the power
cord. The cord can exit either the right or left side of the
insert. Be sur Be sur Be sur Be sur Be sure e e e e t t t t t o pull all slack out o pull all slack out o pull all slack out o o o o of f f f f the po o pull all slack out o pull all slack out
t t t t t o pr o pr o pr o pr o pre e e e e v v v v v en ent t t t t c c c c con en en en on on ontac on tac tac tact t t t t with tac with with with the bott with
The is equipped with a three-prong (grounding)
plug for protection against shock hazard and should be
plugged directly into a properly grounded three-prong
receptacle. DO NO DO NO DO NO DO NO DO NOT CU T CU T CU T CUT OR R T CU T OR REM T OR R T OR R T OR R
I I I I I NG PR NG PR NG PR NG PRONG FR ONG FR ONG FR ONG FRO O O O O M M M M M T T T T T H H H H H E PL E PL E PL E PLUG.
NG PR ONG FR E PL
The blower must be electrically grounded in accor-
dance with local codes or, in the absence of local codes,
with the current NFPA 70- National Electrical Code or
CSA C22.1-Canadian Code.
The blower is controlled by a heat activated switch
(snapstat) that will function only if the blower control
switch is in the AUTO setting. Once the firebox heats
after the burner has been operating for a short time, the
blower will start on either the HI or LOW speed. In AUTO
mode, the blower will continue to operate after the
burner is turned off, until the snapstat cools. See fig. 18.
If blower operation is not desired, place the control
switch in the OFF position to bypass the snapstat
function.
ALWAYS UNPLUG THE BLOWER WHEN
SERVICING THE APPLIANCE.
H I
L O
B L O W E R
Figure 18. Blower Controls
the pow w w w w er c the po the po the po er c er c er c er cor or or or ord d d d d
the bott the bottom o the bott the bott om o om o om of f f f f the fir om o the fir the fir the fir the firebo ebox x x x x . . . . . ebo ebo ebo
EM EM EMO O O O O VE EM VE VE VE T T T T T H H H H H E GR VE E GR E GR E GROU E GR OUN N N N N D- OU OU OU
UG. UG. UG.
UG.
NOTE:
M A N
O F F
A U T O
D- D- D- D-