Tyre Pressure; Changing Engine Oil - Stiga Park COMPACT User Manual

EN
At each basic service and intermediate service car-
ried out at an authorised workshop, the service log
is stamped. A service log presenting these services
is a valuable document that improves the ma-
chine's second-hand value.
5.2 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable(s) from the spark plug(s) and re-
moving the ignition key.

5.3 Tyre pressure

Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).

5.4 Changing engine oil

Change engine oil for the first time after 5 hours of
operation, and subsequently after every 50 hours
of operation or once a season.
Change the oil more often (after 25 hours of oper-
ation or at least once a season) if the engine has to
operate under demanding conditions or if the am-
bient temperature is high.
Use synthetic oil of service grade SF or higher in
accordance with the table below.
Use Oil
All temperatures SAE 10W-30
Below -18°C SAE 5W-30
Above 0°C SAE 30
Use oil without any additives.
Do not fill with too much oil. This can cause the
engine to overheat.
Change oil when the engine is warm.
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. Therefore allow the engine to
cool a few minutes before draining the
oil.
1. Attach the clamp on the oil drainage hose. Use
a polygrip or similar. See fig. 10:V.
2. Move the clamp up 3-4 cm on the oil drainage
hose and pull out the plug.
3. Collect the oil in a collection vessel.
NOTE! Do not spill any oil on the drive belts.
52
ENGLISH
4. Hand in the oil for disposal in accordance with
local provisions.
5. Install the oil drainage plug and move the clamp
back so that it clamps above the plug.
6. Remove the dipstick and fill up with new oil.
Oil volume: 1.4 litres
7. After filling up the oil, start the engine and idle
for 30 seconds.
8. Check to see if there is any oil leakage.
9. Stop the engine. Wait for 30 seconds and then
check the oil level in accordance with 4.2.
5.5 Transmission, oil - filter (4WD)
The oil and filter in the hydraulic power transmis-
sion must be checked/adjusted and changed at the
intervals given in the table below.
Action
Checking – adjusting level.
Changing the oil
Cleaning the filter.
The type of oil is dependent on the hours of opera-
tion according to the table below:
Hours of operation
More than 100
hours of operation/year
Less than 100 hours of
operation/year
Oil quantity when changing: approximately 3.5 li-
tres.
5.5.1 Checking - adjusting
Se "4.2".
5.5.2 Draining
1. Run the machine at variable speeds for 10-20
minutes to heat up the transmission oil.
2. Position the machine completely horizontally.
3. Pull out both disengagement levers according to
fig. 6.
4. Place one container under the rear axle and one
under the front axle.
5. Open the oil reservoir by removing the cover.
See 9:R.
Only a 3/8" square drive may be used
for the filter plug. Other tools will dam-
age the plug.
6. Remove the filter plug from the rear axle. Clean
the hole and use a 3/8" square drive. Remove
the filter and allow the oil in the rear axle and
reservoir to run out. See figure 11.
1st time Then at
intervals
of
Hours of operation
- 50
5 200
Oil type
Synthetic oil 5W-50
SAE30