1. Manuals
  2. Brands
  3. Eneo Manuals
  4. Network Hardware
  5. FNR-4016/500
  6. User manual

Eneo FNR-4016/500 User Manual

16 ip-channels, h.264
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
Network Video Recorder, 16 IP-Channels, H.264
FNR-4016/500

Advertisement

Table of Contents
loading

Related Manuals for Eneo FNR-4016/500

Summary of Contents for Eneo FNR-4016/500

  • Page 1 User Manual Network Video Recorder, 16 IP-Channels, H.264 FNR-4016/500...
  • Page 2 Safety Instructions / Maintenance • Read these safety instructions and the operation manual first before you install and commission the unit. • Keep the manual in a safe place for later reference. • The system may only be commissioned and maintained by personnel authorized to do this and it must only be carried out in accordance with relevant standards and guidelines.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS  C H A P T E R 1..........................4  Introduction............................4  1.1 Front Panel Introduction......................5  1.2 Starting and Shutting Down Your NVR ..................6  C H A P T E R 2..........................7  Network Parameters Configuration ....................7  2.1 Hyper Terminal Setup ....................... 8  2.2 Network Configuration by Hyper Terminal ................
  • Page 4 9.4.5 Exceptions........................46  9.5 Network Configuration ......................47  9.5.1 Basic Configuration ..................... 47  9.5.2 PPPoE Settings......................48  9.5.3 DDNS Settings ......................48  9.5.4 NTP Settings ........................ 48  9.5.5 Net Disk Settings ......................49  9.5.6 E-Mail Settings ......................49  9.6 Channel Configuration ......................50  9.6.1 Channel Display Settings .....................

  • Page 5: Chapter 1

    C H A P T E R 1   Introduction ...

  • Page 6: Front Panel Introduction

      Front Panel Introduction FNR-4016/500 Front Panel: Name Description Turning red indicates power supply but without system running, turning blue Power indicates power supply and system running. Status Alarm Alarm indicator turns red when a sensor alarm is detected. TX/RX TX/RX indictor blinks blue when network connection is functioning properly.

  • Page 7: Starting And Shutting Down Your Nvr

    When the LED is red, please press the Power button on the front panel. The Power indicator will turn blue. The unit will begin to start. Note:  The FNR-4016/500 doesn’t have local output, when Ready indicator turns blue, that means the unit is power on and ready to be configured. Power Off Standard Shutdown Press and hold the POWER button for 3 seconds;...

  • Page 8: Chapter 2

    C H A P T E R 2 Network Parameters Configuration...

  • Page 9: Hyper Terminal Setup

    The FNR-4016/500 NVR is mainly for IPC, DVS network video storage and playback. Network configurations are needed before operating, including: IP address, subnet mask, gateway and port. Note: The factory default username is admin, password is 12345. The factory default IP address of the FNR-4016/500 is 192.168.0.1.
  • Page 10 Step 2: Name the connection and define the icon. Input a name (e.g. HK), select an icon, and press “OK” to enter “Connect To” dialogue box. Step 3: Select the communication port. Select “COM1” in “Connect To” inter face (Please select the COM port according to the reality, in case PC has more than 1 COM.) Press “OK”...
  • Page 11 The parameters should be: Bits per second: 115200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None Press “Apply” and “OK” after the setup. Press “Enter” under Hyper Terminal interface. When “[root@dvrdvs/]#” appears, the connection is established. Figure 2.1.4 Step 5: Disconnect and save connection.

  • Page 12: Network Configuration By Hyper Terminal

    2.2 Network Configuration by Hyper Terminal Enter Hyper Terminal Click “Start”->“Programs”->“Accessories”->“Communications”->“Hyper Terminal”->“HK”, then the Hyper Terminal interface will appear as figure below. Type “Enter”, and the prompt “[root@dvrdvs/]#” will appear which means connection between RS232 interface of PC and RS232 interface of NVR is established successfully by Hyper Terminal. The following operation commands are to accomplish the parameters setup in the prompt.

  • Page 13: Activex Control Installation

    C H A P T E R 3 ActiveX Control Installation  ...
  • Page 14 The FNR-4016/500 can be accessed and configured by web server. Open IE browser, input the IP address of the FNR-4016/500 and then click Enter. The system will remind you to install the ActiveX control. After the installation, you can configure and manage the NVR remotely.

  • Page 15: User Login And Exit

    C H A P T E R 4 User Login and Exit  ...
  • Page 16 Open IE browser, input the IP address of NVR, the web server will select the language automatically according to the system language and maximize the IE browser. Figure 4.1 On the top right corner, language is selectable between Chinese and English. Input the correct user name, password and port, click “Login”...

  • Page 17: Preview

    C H A P T E R 5 Preview  ...

  • Page 18: Preview

    After login, the preview interface will display: Figure 5.1 Interface description: Area Description Area Description Channel list Live view Video adjustment Play control Play control buttons description: Button Description Button Description 4 windows division 1 window division 16 windows division 9 windows division Stop all preview Capture image...

  • Page 19: Preview

    5.1.2 Preview Preview by channel: After choosing window division mode, select one window, and click on channel list to preview the current channel. If preview successful, the icon will become Preview by page: Click the device node on the list, then multiple channels will start to display synchronously according to the selected window divisions.

  • Page 20: Stop Preview

    5.1.4 Stop Preview    Click on the playlist, it will become . This can stop the channel preview. Click to stop all channels preview. 5.2 Recording and Capturing Image The previewing channel is required when recording and capturing image. Note: When stop previewing, will also stop the recording of this channel. 5.2.1 Recording ...

  • Page 21: Capturing Image

    Note: If saving file disk space is less than 500M, the web server will stop recording automatically. 5.2.2 Capturing Image    Click “Config” to enter local configuration menu, where can modify the saving capturing image directory. Select a previewing window, click to capture image. If capture image successfully, the saving folder will pop up automatically.

  • Page 22: Chapter 6

    C H A P T E R 6 PTZ Control  ...
  • Page 23 If the front-end connects with PTZ, PTZ control is available when preview. With the direction buttons, it can achieve 8 directions control. Also zoom, focus, iris, light and wiper are adjustable. Click to enable auto scan, click again to stop it. If preset point is set, the point can be called by selecting in the draw down list and clicking...

  • Page 24: Chapter 7

    C H A P T E R 7 Playback  ...
  • Page 25 Click “Playback” to enter playback menu. Figure 7.1 Playback interface description: Area Description Area Description Channel list Playback video Playback control Playback status Calendar Download/ Backup Timeline Playback control buttons description: Button Description Button Description Stop Play Speed up Slow down Snapshot Play by single frame Open/Close audio...

  • Page 26: Playback Query

    7.1 Playback Query Step 1: Select a channel on the channel list. (Channel 1 is the default.) Step 2: Select a date in calendar. Step 3: Click “Search” to search the matched recorded files. If there are search results, then they will be shown in the time line area.

  • Page 27: Capturing Image And Download

    Recording file location: Click , input the time in the pop-up box and click “Go”. This will start the file playback from the specified time. Drag timeline, and set “ ” to the specified time to play back the video. 7.3 Capturing Image and Download Click “Config”...

  • Page 28: Remote Backup

    During download, the window will display the file number and download progress. 7.4 Remote Backup The FNR-4016/500 supports local one key backup function, and it can also support backup to USB storage devices remotely. After searching files, click to pop up a new page where list all the files for the specific day.

  • Page 29: Chapter 8

    C H A P T E R 8 Log Search ...
  • Page 30 Click “Log” to enter log query menu: Figure 8.1 Select the log type and date, and click to list all matched logs. Enable “Start” as to search the log file in a certain period of a day. Click can export the logs as Excel or TXT file. Note: Up to 2000 logs can be listed;...

  • Page 31: Chapter 9

    C H A P T E R 9 Configuration   ...

  • Page 32: Local Configuration

    Click “Config” button in the menu bar and enter parameters setup menu, which displays local configuration by default. 9.1 Local Configuration Figure 9.1 Local Parameters Information: Parameters Descriptions Protocol Type Select network transmission protocol: TCP or UDP. The Size of File Packaging Set the size of recordings Main Stream for recording.

  • Page 33: Ip Camera Configuration

    Click “Remote Config” and enter IP camera configuration menu. Figure 9.2 Model Name IP camera connections FNR-4016/500 Up to 16-ch D1 or 8-ch 720P or 4-ch UXGA IP cameras Note:    For FXC-1201M IP camera at UXGA resolution, up to 4 channels to FNR-4016 model.

  • Page 34: Quick Add Of Ip Camera

    9.2.1 Quick Add of IP camera  The FNR-4016/500 provides a function of remote auto searching IP camera. When there are supported IP cameras in the same network segment of a LAN with NVR, you may add it in one button with default user name, password and port number.
  • Page 35 First, select a Channel No. then click and the on-line IP cameras will be listed as figure below shown: Figure 9.4 Select one camera in the list and click to finish. Then you can change IP address, sub mask or user name, password in the menu on the right, and click “Modify” to confirm.

  • Page 36: Recording Settings

    9.3 Recording Settings Click “Remote Config” and select to enter remote settings menu where you can configure recording, alarm, network settings and etc. Figure 9.5...

  • Page 37: Video Parameters

    9.3.1 Video Parameters  Figure 9.6 Settings for recording: Items Descriptions Encoding Main Stream (Normal/Event) and Sub stream. Parameters Stream Type Video and Video & Audio Resolution Recording Resolution Bit rate Type Variable and Constant Frame Type BBP,BP and Single P 9.3.2 Schedule Recording  Step1: Enable Schedule Recording. Note: When NVR is succeed to connect to IP camera, it will start schedule recording which means recording for 7/24.
  • Page 38 Figure 9.7 Step 2: Set recording time and type. Click Settings button besides to “Record Time” to enter setup page. Select one day in a week, and select All Day recording if necessary. You may also set period recording by disable All Day Recording;...

  • Page 39: Motion Detection Recording

    Figure 9.8 Note: If you are using IP camera that is not from eneo, please setup this function by using its own software. Step 1: Select Channel No. for motion detection recording. Step 2: Enable motion detection by tick the box.
  • Page 40 Step 4: Tick box of Start Draw and draw an area on the image by lift-pressing and holding the mouse. Double-click can select full screen. Step 5: Select a sensitivity level for motion detection. Level 1 is the lowest, 6 is the highest. Step 6: Arm Schedule Setup You may select one day in a week, or select several time periods in one day.

  • Page 41: Alarm Recording

    “NO” is the default status. The settings will become effective after rebooting. If you are using IP camera that is not from eneo, please setup this function by using its own software. Step 3: Enable “Alarm Handle” to activate “Arm Schedule”...
  • Page 42 Step 4: Set the fortify time for alarm input. Click “Settings” in “Fortify Time” menu. Select “Weekday” as some day of the week or the whole week for recording time. The “All Day Record” or 8 “Segments” can be selected as well.

  • Page 43: Other Recording Modes

    Step 7: Select one day in a week, and select All Day recording if necessary. You may also set period recording by disable All Day Recording; there are 8 time periods in one day. Then you can select Alarm Recording from the drop-down menu beside the periods.

  • Page 44: Signal Level Alarm

    Step 5: Set the alarm linkage for motion detection and select alarm output channel. Alarm Linkages Description: Linkage Description When the alarm signal is detected, the image of corresponding channel will pop out as Warning on Monitor single screen. Audio Warning Alarm triggers buzzer Upload to Center Upload the alarm signal to the center, such as client software...

  • Page 45: Video Loss

    9.4.3 Video Loss  Note:  This function is only available on IP cameras from eneo. Step 2: Enable “Video Loss” to activate settings of “Fortify Step 1: Select the channel number for video loss. Time” and “Linkage”...

  • Page 46: Video Tampering

    Step 4: Set linkage for video loss. Click “Settings” in the “Linkage” menu. 9.4.4 Video Tampering  Note: This function is only available on IP cameras from eneo. Step 1: Select the channel number for video tampering. Select Step 2: Enable “Video Tampering Alarm” to activate settings...

  • Page 47: Exceptions

    域、布防时间和联动方式的设置。 Step 3: Set the video tampering area and sensitivity. The sensitivity can be divided into three levels: Low, Medium, and High. Enable “Start Draw”, and select the detection area by using mouse. Step 4: Set the fortify time for video tampering. Click “Settings”...

  • Page 48: Network Configuration

    Select the exception type and handle method. Select to enter configuration interface. 9.5 Network Configuration 9.5.1 Basic Configuration  Select Configure the network according to the actual situation. If there is DHCP server in the network, enable “Obtain Auto” and reboot the device to get the IP address under this network segment automatically.

  • Page 49: Pppoe Settings

    9.5.2 PPPoE Settings  Select Enable PPPoE by ticking , input the user name and password, then save the changes and reboot the device to make the parameters become effective. If succeed to dial, the current IP address will be displayed in the blank “DDNS IP”. 9.5.3 DDNS Settings ...

  • Page 50: Net Disk Settings

    If server authentication is needed, enable it (i.e. ) and input user name and password. Input the sender and recipient information, if it needs to send picture, you can enable “Attachment” (i.e. Note: Currently the function of captured picture attachment is invalid for the FNR-4016/500.

  • Page 51: Channel Configuration

    9.6 Channel Configuration 9.6.1 Channel Display Settings  Note: This function is only available on IP cameras from eneo. Select You can configure channel name, OSD and related parameters here. 9.6.2 Video Mask    Note: This function is only available on IP cameras from eneo. Step 1: Select channel number, and enable video mask (i.e.

  • Page 52: Account Management

    Step 2: Set the mask area. Click “Settings” to enter area set menu. Enable “Start Draw” (i.e. ), select the mask area by clicking and dragging the mouse. Note: Max. 4 areas can be configured in one image. 9.7 Account Management The default user name and password of device administrator are “admin”...

  • Page 53: Remote Upgrade

    Click “Add” to add user. Note: If you set the IP address or physical address, and then only the PC with the same IP address or physical address can visit the device through network. Note: Local PTZ Control: Locally control PTZ cameras. Local Manual Record: Locally start and stop manual recording on any of the channels.

  • Page 54: Hdd Settings

    9.9 HDD Settings HDD Formatting: Click Note: Please backup the data before formatting hard disk. Disk Group Management： Select one disk and select one HDD Group you want it to be shown as figure right. Note: NVR supports up to 16 HDD Groups. HDD Property Settings: Select one disk, and configure its property by selecting Read-Write, Read-Only or redundant from drop-down menu,...
  • Page 55 HDD Group record channel: Click “HDD Group attribute” button to enter setup page. First select a HDD group and then tick channels you want to record in this HDD group, and then click OK to finish Note: Recording the images of one channel in one HDD group is recommended.

  • Page 56: Appendix

    C H A P T E R 10 Appendix   ...

  • Page 57: Glossary

    Glossary DHCP Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices (DHCP clients) to obtain configuration information for operation in an Internet Protocol network. Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers over a network. PPPoE PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames.

  • Page 58: Faq

    • Why does my NVR make a beeping sound after booting? There are a few reasons for the warning beep your NVR makes after booting. 1. There is no HDD present in the NVR. 2. The HDD has not been initialized. 3.

  • Page 59: Specifications

    Remote configuration Password protection Supply voltage 100 to 240VAC, 50/60 Hz Intergrated writer Firmware update via remote software, USB Flash drive Supported network suppliers eneo F series ONVIF Dimensions (HxWxD) 442x457x88 mm Weight 8.0kg Certificates Optional Accessories The optional accessories currently available can be found on our Homepages: www.videor.com and www.
  • Page 60         ® eneo is a registered trademark of Videor E. Hartig GmbH Exclusive distribution through specialised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany Tel. +49 (0) 60 74 / 888-0 · Fax +49 (0) 60 74 / 888-100 www.videor.com...

Table of Contents