Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Paslode IM250A
Summary of Contents for Paslode IM250A
- Page 1 Part No. 900600 Model IM250A OPERATING MANUAL IMPORTANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2012 llinois Tool Works Inc. www.paslode.com 405630-21 02/12...
-
Page 2: Table Of Contents
Contents Subject Page Introduction and Warranty ............................... 2 An Overview of the Paslode Cordless 16 Gauge Angled Finish Nailer................3 Safety Instructions ................................4 Battery and Charger ................................ 7 Fuel Cell and Metering Valve ............................9 Preparing the Paslode Cordless 16 Gauge Angled Finish Nailer for Use..............12 Paslode Cordless 16 Gauge Angled Finish Nailer Operation.................. -
Page 3: Introduction And Warranty
ONE-YEAR LIMITED WARRANTY Paslode's sole liability hereunder will be to replace any part or accessory A one-year warranty will apply to all parts, except those listed which proves to be defective within the specific time period. Any replacement below as normal wearing parts, or parts which are specifically... -
Page 4: An Overview Of The Paslode Cordless 16 Gauge Angled Finish Nailer
Specifications Dimensions: Weight- 4 lbs 14oz. with battery The Paslode Cordless 16 ga. Angled Finish Nailer is a self- contained, fully portable nailer that uses liquid hydrocarbon Height 11-1/2 inches fuel to power a unique linear drive internal combustion motor. -
Page 5: Safety Instructions
The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Cordless 16 ga. Angled Finish Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Do not expose the tool to PRECAUTIONS AND MANUAL INSTRUCTIONS. - Page 6 Paslode Cordless 16 ga. Angled NEVER operate the tool if the work contacting element Finish Nailer.
- Page 7 Battery Disposal: The Paslode batteries contain cadmium and must be recycled or disposed of properly. It is illegal in some areas to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling in your area.
-
Page 8: Battery And Charger
Paslode batteries (either round or oval ). The first mount unit’s plug into plug receptacle on the back step in preparing a new tool for operation is to fully of the charger (see picture). - Page 9 Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery.
-
Page 10: Fuel Cell And Metering Valve
Never inhale the spray. NOTE: Altitude Restriction Keep out of the reach of children. Paslode Cordless technology is powered by an internal Store fuel cell(s) in well-ventilated areas only. combustion engine and are effected by altitude. The tool may lose power or become erratic at elevations of 4000 feet or greater.When using the tool at elevations... - Page 11 Paslode takes no responsibility for proper fuel cell disposal. Proper disposal remains the responsibility of sellers and users. All sell- ers and users must contact their local solid waste authority to determine if any federal, state or local regulation prohibits or restricts disposal.
- Page 12 Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Cordless Finish Nailer, you will notice a yellow adapter at Inserting the metering valve/fuel cell assembly into the the top of the cylinder pocket. As shown in the illustration, Cordless Finish Nailer is very simple.
-
Page 13: Preparing The Paslode Cordless 16 Gauge Angled Finish Nailer For Use
✕ all warranty claims. Loading Fasteners STEP 1: Align the heads of the Paslode 16 ga. Angled Finish nails to the silver brad channel in the rear of the magazine s l i STEP 2: Next, while applying pressure to the release lever,... -
Page 14: Paslode Cordless 16 Gauge Angled Finish Nailer Operation
Paslode Cordless 16 ga. Angled Finish Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion Turn chamber and adjustment mixed with air by wheel the fan. in either direction... -
Page 15: Fasteners And Applications
The Paslode Cordless 16 ga. Angled Finish Nailer drives Paslode 16 Gauge Angled Finish Nails. Fasteners are collated into strips of 50 for easy loading. Paslode fasteners are designed to be used in Paslode tools, use of other fasteners may cause damage to the tool or injury to the tool operator. -
Page 16: Servicing
If you have any reason to believe that your problem is beyond the Finish Nailer, clearing a jammed fastener is easy: service procedures in this manual, contact your Paslode ® representative immediately. 1. Remove the battery. - Page 17 Automotive Adapter - Part No. 900507 Paslode Cordless Finish Nailer Case - Part No. 900713 Paslode Cordless Trim Tool Tune-Up Kit - Part No. 219304 High Altitude Valve Kit - Part No. 219247 End-of-Workday Routine (for fuel cells at altitudes from 4000 to 9000 feet) These simple steps are based on maintaining the safety and operational efficiency of the Cordless Finish Nailer.
-
Page 18: Troubleshooting
Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head. No spark is generated. Return tool to authorized Paslode ® dealer for service. -
Page 19: Forest Edge Drive Vernon Hills, Illinois
® If tool will not operate after following the above service directions, return the tool to an authorized Paslode representative for service. For Technical support call 1-800-222-6990 or visit our web site at www.paslode.com.. To purchase parts, visit our website at www.itwconstructionparts.com.
Need help?
Do you have a question about the IM250A and is the answer not in the manual?
Questions and answers