Paslode IM250A Operating Manual
  1. Manuals
  2. Brands
  3. Paslode Manuals
  4. Nail Gun
  5. IM250A
  6. Operating manual

Paslode IM250A Operating Manual

16 gauge cordless angled finish nailer
Hide thumbs Also See for IM250A:

Advertisement

Table of Contents

P
CORDLESS
IMPORTANT!
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
Printed in U.S.A.
© 2002 Illinois Tool Works, Inc.
405630-9
03/02
Model: IM250A
Part No. 900600
Angled Finish Nailer
OPERATING MANUAL
www.paslode.com
19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IM250A and is the answer not in the manual?

Questions and answers

Related Manuals for Paslode IM250A

Summary of Contents for Paslode IM250A

  • Page 1 Model: IM250A Part No. 900600 Angled Finish Nailer CORDLESS OPERATING MANUAL IMPORTANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2002 Illinois Tool Works, Inc.

  • Page 2: Table Of Contents

    Contents Subject Page Introduction and Warranty ..........2 An Overview of the Paslode Angled Finish Nailer ... 3 Safety Instructions ............4 Battery and Charger ............7 Fuel Cell and Metering Valve .......... 9 Preparing the Paslode Angled Finish Nailer for Use ..12 Paslode Angled Finish Nailer Operation .......

  • Page 3: Introduction And Warranty

    Paslode's sole liability hereunder will be to replace any part or accessory delivery to the original user. which proves to be defective within the specific time period. Any replacement...

  • Page 4: An Overview Of The Paslode Angled Finish Nailer

    Cycle Rate: Intermittent Operation – 2 to 3 nails Paslode Angled Finish nailer. As you can see in the illustration per second below, the Paslode Finish nailer is made up of three major Continuous Operation –...

  • Page 5: Safety Instructions

    The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Angled Finish Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Do not expose the tool to PRECAUTIONS AND MANUAL INSTRUCTIONS.
  • Page 6 NAILER IF PARTS ARE LOOSE, DAMAGED OR MISSING. The Paslode Angled Finish Nailer is not a toy – it is a tool. Careless and improper use may result in a serious 10. DO NOT DRIVE FASTENERS INTO KNOTS OR ON accident.
  • Page 7 AND BATTERY REMOVED. loss of balance. Always be aware of edges and Store the fuel cell in the case with the Paslode Angled drop-offs when nailing on Finish Nailer. rooftops and other high 17. KEEP THE TOOL CLEAN.

  • Page 8: Battery And Charger

    Battery Charger Kit - Part No. 900200 Wall Mount Transformer* - Part No. 900477 Plug Battery Charger Base* - Part No. 900476 Automotive Adapter* - Part No. 900507 THE PASLODE BATTERY CHARGING SYSTEM * Cannot use with previous (gray in color) charging system components.
  • Page 9 BATTERY INDICATOR LIGHT Inserting Battery 1. Load the battery, contacts first, into the Paslode Angled Finish nailer. 2. Push battery fully forward into its locked position. 3. To remove battery, push down on locking tab and slide battery out.

  • Page 10: Fuel Cell And Metering Valve

    E X P L O S I O N / F I R E fuel container, much as you squeeze a tube of toothpaste. HAZARD This squeezing action ensures that all the fuel is used, and that the Paslode Finish nailer can operate in any position. Read safety instructions before using Because of this container-within-a-container design, you or handling the fuel cell.
  • Page 11 Fuel Cell and Metering Valve Attaching Metering Valve to Fuel Cell To attach the metering valve to a fuel cell: 1. Press downward on the front side of the valve (stem side) until it seats. 2. Press downward on the rear side of the valve until it seats. 3.
  • Page 12 Close the actuator cover to complete the loading of fuel in the Paslode Angled Finish Nailer. Do this by swinging it up and over the fuel valve/cylinder assembly, and pushing down until the actuator cover snaps into position.

  • Page 13: Preparing The Paslode Angled Finish Nailer For Use

    Loading Fasteners STEP 1: Align the heads of the Paslode angled finish nails to the silver brad channel in the rear of the magazine and insert one or two strips. Push the nails strips forward.

  • Page 14: Paslode Angled Finish Nailer Operation

    Paslode Angled Finish Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion Turn chamber and adjustment mixed with air by wheel in the fan. either direction SQUEEZE TRIGGER Spark plug ignites...

  • Page 15: Fasteners And Applications

    The Paslode Angled Finish Nailer drives Paslode 16 Gauge angled finish nails. Fasteners are collated into strips of 50 for easy loading. Paslode fasteners are designed to be used in Paslode tools, use of other fasteners may cause damage to the tool or injury to the tool operator.

  • Page 16: Servicing

    There are certain problems you may encounter when you If fuel is not released with each operation of the metering are using the Paslode Angled Finish Nailer that you will be valve, this indicates that there is no more fuel left in the able to correct on the work site.
  • Page 17 The air filter simply lifts out. 2. Wipe your Paslode Angled Finish Nailer with a clean, Tap the filter GENTLY to remove any dust. Check and clean soft cloth.

  • Page 18: Troubleshooting

    Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head. No spark is generated. Return tool to authorized Paslode ® dealer for service.

  • Page 19: Forest Edge Drive Vernon Hills, Illinois

    Work-contacting element is bent, or is dirty. element. tool cycles. ® If nailer will not operate after following the above service directions, return the tool to an authorized Paslode representative for service. ® For the nearest Paslode representative call 1-800-682-3428.
  • Page 20 IM250A 900600 PASLODE MODEL NUMBER DESIGNATION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it. The following example illustrates the information contained in this tool model number. Angled Finish Nailer...

Table of Contents

Save PDF