Table of Contents
Advertisement
Quick Links
300918- 08-13-02.qxd
Instruction
manual
U. S. Design Patent D456,234
U. S. Design Patent D456,685
U. S. Design Patent D458,825
Other Patents Pending
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Copyright © 2002 Porter-Cable Corporation
9/13/02
3:25 PM
Page 1
Double Insulated
Disc Grinder
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 25
MODEL
7418
IMPORTANT
Part No. 300918 - 08-13-02
Advertisement
Table of Contents
Related Manuals for Porter-Cable 7418
Summary of Contents for Porter-Cable 7418
- Page 1 U. S. Design Patent D456,685 U. S. Design Patent D458,825 Other Patents Pending IMPORTANT Please make certain that the person who is To learn more about Porter-Cable to use this equipment carefully reads and visit our website at: understands these instructions before http://www.porter-cable.com starting operations.
-
Page 2: General Safety Rules
300918- 08-13-02.qxd 9/13/02 3:25 PM Page 2 GENERAL SAFETY RULES WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. - Page 3 300918- 08-13-02.qxd 9/13/02 3:25 PM Page 3 Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting.
-
Page 4: Specific Safety Rules And Symbols
WARNING: There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written Porter-Cable and we have advised you. -
Page 5: Additional Safety Rules For Paint Removal
300918- 08-13-02.qxd 9/13/02 3:25 PM Page 5 ______ – – – – ......alternating current ......three-phase alternating current ......three-phase alternating current with neutral ......direct current ......no load ......alternating or direct current ......Class II Construction ...... -
Page 6: Replacement Parts
When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. -
Page 7: Functional Description
3:25 PM Page 7 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable disc grinders are designed for numerous grinding operations. Typical applications are auto body grinding, smoothing welding beads, removing gates and flash from castings, and removing rust. TO START AND STOP THE MACHINE CAUTION: Make sure switch is OFF and power circuit voltage is the same as that shown on the specification plate. - Page 8 300918- 08-13-02.qxd 9/13/02 3:26 PM Page 8 TO INSTALL WHEEL GUARD A TYPE 27 wheel guard is furnished with the tool. A TYPE 1 wheel guard is available as an accessory for cut-off wheels. Both guards are installed and adjusted in the same manner. WARNING: Always use an approved, and properly adjusted wheel guard where required (see ACCESSORIES Section of this manual).
-
Page 9: Operation
300918- 08-13-02.qxd 9/13/02 3:26 PM Page 9 Position inner flange (A) Fig. 6 onto spindle (B), with round hub facing outward, away from machine. Rotate flange until it drops into place on the spindle. CAUTION: Use Type 1 Wheel Guard when using Type 1 cut-off Wheels. -
Page 10: Maintenance
FACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricate with fresh lubricant. Have new brushes installed, and test the tool for performance. - Page 11 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
- Page 12 300918- 08-13-02.qxd 9/13/02 3:26 PM Page 12 NOTES...
- Page 13 Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable •...