Page 1
6 PO (150 MM) AMOLADORA DE BANCO DE 6 PULG. (150 MM) Instruction Manual Manuel d’instructions Manual de instrucciones www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. CATALOG NUMBER ADVERTENCIA: LÉASE ESTE PCXB515BG INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
SAVE THESE INSTRUCTIONS SAFETY GUIDELINES - DEFINITIONS WARNING ICONS Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to and/or instruct you how to avoid a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool better and safer.
POWER TOOL SAFETY GENERAL SAFETY INSTRUCTIONS 9. USE THE RIGHT TOOL. Do not force the BEFORE USING THIS POWER TOOL tool or an attachment to do a job for which Safety is a combination of common sense, it was not designed. staying alert and knowing how to use your power tool.
Page 5
16. REDUCE THE RISK OF 21. DO NOT OVERREACH. Keep proper UNINTENTIONAL STARTING. Make footing and balance at all times. sure switch is in the OFF position before plugging the tool in. 22. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest 17.
BENCH GRINDER SAFETY SPECIFIC SAFETY INSTRUCTIONS FOR 13. GUARD AGAINST ELECTRICAL THIS BENCH GRINDER SHOCK by preventing body contact with grounded surfaces. For example: pipes, Wear eye protection that complies radiators, ranges, refrigerator enclosures. with ANSI Z87.1 specifications. 14. DO NOT use wheels with incorrect size holes.
Page 7
24. FREQUENTLY clean grinding dust from 31. IF ANY PART OF THIS GRINDER IS beneath the grinder. MISSING or should break, bend, fail in any way, or should any electrical 25. DO NOT OPERATE THIS TOOL WHILE component fail to perform properly, UNDER THE INFLUENCE OF DRUGS, shut off the power switch, remove the ALCOHOL OR ANY MEDICATION.
ELECTRICAL REQUIREMENTS AND SAFETY POWER SUPPLY AND MOTOR Use a separate electrical circuit for your tool. SPECIFICATIONS This circuit must not be less than #18 wire and should be protected with a 2.1 Amp time WARNING lag fuse. Before connecting the motor to the To avoid electrical hazards, fire hazards, power line, make sure the switch is in the off or damage to the tool, use proper circuit...
Page 9
GLOSSARY OF TERMS WARNING WHEEL GUARD - Covers the grinding wheels and protects against accidental This tool is for indoor use only. Do not expose contact. to rain or use in damp locations. WHEEL COVER - Covers the grinding wheels This tool is intended for use on a circuit that and provides access for routine maintenance.
TOOLS NEED FOR ASSEMBLY Not Supplied 8 mm & 13 mm Phillips Screwdriver Adjustable Wrench open wrench CARTON CONTENTS UNPACKING AND CHECKING CONTENTS Carefully unpack the grinder and all its parts, and compare against the list below and the illustration to the right. With the help of an assistant place the grinder on a secure surface and examine it carefully.
ASSEMBLY AND ADJUSTMENTS Estimated Assembly Time: 10 - 20 Minutes. INSTALLING THE LED LIGHT AND EYE SHIELD ASSEMBLY (FIG. B, C) WARNING 1. Bag "F" - Tighten the LED light • To avoid injury, do not connect this assembly (1) to grinder with two bench grinder to the power source composite screws (2) using a Philips until it is completely assembled and...
Page 14
Move the Battery section from page 15 to here 5. Loosen the hex nut (9) by an adjustable CHANGING GRINDING WHEELS wrench as shown in Figure F. (FIG. D, E, F, G, H) NOTE: The nut on the left side of the CAUTION grinder has a standard left-hand thread Turn off and unplug the bench grinder.
Page 15
8. Install the new wheel and make sure both Fig. I wheel flanges (10, 12) are in place with the concave sides toward wheels. 9. To prevent wheel rotating, place a wood wedge (13) (not supplied) between the wheel and the wheel cover as shown in Figure H.
OPERATION STARTING AND STOPPING THE GRINDER GENERAL OPERATION (FIG. K) CAUTION Keep all bystanders a safe distance away WARNING from the tool and not in direct line, front or To avoid injury, always keep the plug back of the grinder. disconnected from the power source 1.
Page 17
SCREWDRIVERS DRESSING A GRINDING WHEEL (FIG. M) The end of a properly sharpened screwdriver Bring the dressing tool forward on the tool will be a perfect rectangle, absolutely flat rest until it touches the high point on the face and perpendicular to the center line of the of the wheel.
Do not use any accessory unless you Since accessories, other than those offered have completely read the Instruction by Porter-Cable, have not been tested with Manual for that accessory. this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Porter-Cable recommended accessories should be used with this product.
Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.com. You can also order parts from your nearest Porter-Cable Factory Service Center or Porter-Cable Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 609-9779.
PARTS LIST 6 IN. (150 MM) BENCH GRINDER PARTS LIST ID NO. Description Size Q’ty X71S Small carriage bolt M5*48 X71R Eyeshield X71Q Eyeshield locking knob X71P Philips screw with spring & flat washer M5*8 X71N Eyeshield bracket X71M Philips screw M5*42 X71L Right safty guard cover...
90 DAYS MONEY BACK GUARANTEE: If you are not completely satisfied with the performance of your PORTER-CABLE Power Tool for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.