King Canada KC-705L-5 Instruction Manual
  1. Manuals
  2. Brands
  3. King Canada Manuals
  4. Sander
  5. KC-705L-5
  6. Instruction manual

King Canada KC-705L-5 Instruction Manual

4" x 36" belt and 6" disc sander
Hide thumbs Also See for KC-705L-5:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
KING CANADA
4" x 36" BELT AND
6" DISC SANDER
MODEL: KC-705L-5
INSTRUCTION MANUAL
COPYRIGHT © 2007 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

Advertisement

Table of Contents
loading

Related Manuals for King Canada KC-705L-5

Summary of Contents for King Canada KC-705L-5

  • Page 1 KING CANADA 4” x 36” BELT AND 6” DISC SANDER MODEL: KC-705L-5 INSTRUCTION MANUAL COPYRIGHT © 2007 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
  • Page 2 LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials.

  • Page 3: Safety Instructions For Your Belt Disc Sander

    SAFETY INSTRUCTIONS FOR YOUR BELT AND DISC SANDER SAFETY INSTRUCTIONS FOR BELT AND DISC SANDER BEFORE EACH USE: Safety is a combination of common sense, staying alert and knowing how your belt disc sander works. Read this manual to Inspect your sander. understand this sander.
  • Page 4 SAFETY INSTRUCTIONS FOR YOUR BELT AND DISC SANDER USE THE RIGHT TOOL. Don’t force tool or attachment to do a job Plan the way you will hold the worpiece from start to finish. it was not designed to do. Avoid awkward operations and hand positions where a sudden slip CAUTION: This machine is not designed for heavy deburring could cause fingers or hand to move into a sanding surface.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS POWER TOOL WARRANTY................................SAFETY INSTRUCTIONS FOR YOUR BELT DISC SANDER ......................1-2 TABLE OF CONTENTS ..................................3 GETTING TO KNOW YOUR BELT AND DISC SANDER........................4 ON-OFF SWITCH ....................................5 UNPAKING AND CHECKING CONTENTS............................6 ASSEMBLY ....................................7-10 MOUNTING BELT AND DISC SANDER TO WORKBENCH ......................7 CLAMPING BELT AND DISC SANDER TO WORKBENCH......................7 INSTALLING SANDING DISC AND GUARD ............................7 INSTALLING BACKSTOP ..................................8...

  • Page 6: Getting To Know Your Belt And Disc Sander

    GETTING TO KNOW YOUR SANDER 4-Tension lever Auxiliary mounting hole Work support hex. screw Belt bed 2- Bed locking hex. hd. screw 3- Tracking knob 5-Table lock knob Mounting hole Base 1- Work support Sanding belt Sanding plate Sanding disc Disc worktable Disc guard 7- On-Off switch...

  • Page 7: On-Off Switch

    ON-OFF SWITCH The On-Off switch has a locking feature. THIS FEATURE IS INTEN-DED TO HELP PREVENT UNAUTHORIZED AND POSSIBLY HAZARDOUS USE BY CHILDREN AND OTHERS. 1.To turn machine "ON", insert key into switch. NOTE: Key is made of yellow plastic, located in loose parts bag. 2.

  • Page 8: Unpaking And Checking Contents

    UNPACKING AND CHECKING CONTENTS UNPAKING AND CHECKING CONTENTS Separate all parts from packing materials and check each item with illustration and "Table of Loose Parts." NOTE: Make certain all items are accounted for, before discarding any packing material. WARNING: To avoid injury, if any parts are missing, do not attempt to assemble the Belt and Disc Sander, plug in the power cord, or turn the switch on, until the missing parts are obtained and installed correctly.

  • Page 9: Assembly

    ASSEMBLY MOUNTING BELT AND DISC SANDER TO WORKBENCH If the belt and disc sander is to be used in a permanent location, it should Outline of sander 2 Holes be fastened securely to a firm supporting surface such as a workbench. 3/8”...

  • Page 10: Installing Backstop

    ASSEMBLY INSTALLING BACKSTOP Lock washer Flat washer Hex. Screw Work support hex. screw 1. Locate backstop and hex. screw, washer and lockwasher. Backstop 2. Hold work support into position and fasten as shown. Do not overtighten. Wrench INSTALLING TABLE ASSEMBLY 1.

  • Page 11: Auxilliary Mounting For Vertical Sanding

    ASSEMBLY 8. Use your Instruction manual as a spacer. Place ten pages of the Instruction manual Instruction manual between the disc and the front edge of the table. Hold the table against the manual and tighten the three (3) hex. hd. screws.

  • Page 12: Installing The Sanding Belt Tensioning And Tracking

    ASSEMBLY INSTALLING THE SANDING BELT- Idler drum TENSIONNING AND TRACKING Tension lever WARNING: To avoid injury from accidental starting, turn switch "OFF”, remove key and remove plug from power source outlet before removing Directional arrow Sanding belt or installing sanding belt. On the smooth side of the sanding belt, you will find a "directional arrow".

  • Page 13: Basic Operation

    BASIC OPERATION BEFORE USING THE SANDER To avoid fire damage, never use the sander near flammable liquids WARNING: To avoid mistakes that could cause serious, permanent vapors or gases. injury, do not plug the sander in until the following steps are completed.

  • Page 14: Bevel Sanding

    BASIC OPERATION -Never use this tool to finish pieces too small to hold by hand. Make sure the sanding disc turns counterclockwise before using -Use extra supports (table, saw horses, blocks, ect.) for any the sander. workpieces large enough to tip when not held down to the table top. KEEP CHILDREN AWAY.

  • Page 15: Positioning Belt Table

    BASIC OPERATION POSITIONING BELT BED Backstop Belt bed A bed locking hex. socket head screw locks the belt bed in a Hex. soc. screw vertical or horizontal position.To adjust vertical position: Hex. Key 1. Remove the backstop. 2. Loosen the hex socket head locking screw using a 6mm hex wrench.

  • Page 16: Sanding Curved Edges

    BASIC OPERATION SANDING CURVED EDGES Always sand inside curves on the idler as shown. Drive drum WARNING: Never attempt to sand the ends of a workpiece on the idler drum. Applying the end of the workpiece to the idler drum could cause the workpiece to fly up and result in an injury.

  • Page 17: Maintenance

    MAINTENANCE WARNING: For your own safely, turn switch "OFF" and remove plug from power source outlet before adjusting, maintaining, or lubricating your belt and disc sander. WARNING: To avoid electrocution or fire, any repair to electrical systems should be done by qualified service technicians. Unit must be reassembled exactly to factory specifications.

  • Page 18: Installing Pulley Cover

    MAINTENANCE & TROUBLESHOOTING 6.Test belt tension by placing fingers on either side or belt and squeeze. There should be about a 1/4" give to the belt. NOTE: Excessive tightness on pulley belt may cause increased noise and over load motor. Excessive looseness on pulley belt may cause belt to fail prematurely.

Table of Contents