Air Flow Velocity And Direction Adjustment; Plasma Duo - Mitsubishi Electric MSZ-FA25VA Operating Instructions Manual

SUPPLEMENT
To air-condition mainly
the left area of the room
Remote controller button Press to select LEFT.
Remote controller display
i-see Sensor operation
Control range Installed
of horizontal air
at center
flow direction.
The vertical air
flow direction Installed
conforms to the
at left
setting on the re-
mote controller.
(The horizontal
Installed
air flow direction
at right
is controlled in
this range. )
Indoor unit
AREA
display

AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT

AIR FLOW velocity and direction can be selected as required.
■
To change the AIR FLOW velocity, press the
Each time the button is pressed, the fan speed is changed in sequence:
(Low) →
• Use the
• If the operating sound of the air conditioner disturbs your sleep, use the
■
To change the AIR FLOW blowing direction vertically, press the
VANE
Each time the button is pressed, the angle of the horizontal vane is changed in
sequence:
SWING OPERATION
Use the swing operation for the air flow to reach all corners of the room.
Recommended horizontal vane range for more efficient air-conditioning
Use the
Use position
use positions
adjusting to your requirements.
9
To air-condition the entire room To air-condition mainly
The horizontal air flow direction and in- the right area of the room
door unit display are switched accord-
ing to the room temperature (floor/wall).
Press
Press to select AUTO.
RIGHT.
or
or
(Med.) → (High) → (Super High) →
(Super High) notch to cool/heat the room more efficiently.
(Low) notch.
button.
(1) → (2) → (3) → (4) → (SWING) →
(AUTO) position usually.
(1) in the COOL or DRY mode and
(2) to (4) in the HEAT mode when
Movement of the horizontal vane
to select
• The vane automatically moves to horizontal position.
It will not swing.
NOTE:
Air blows out upper than position (1).
• To constantly change the air flow direction, select
(SWING) with the
When the air flow direction is
set to position (2), (3) or (4)
• After around one hour of operation, the air condi-
tioner automatically moves the vane to position (1).
To change the air flow direction to the original set-
ting, operate the VANE button on the remote con-
FAN
troller again.
button.
• The vane does not move to the straight-down posi-
tion in the COOL and DRY mode.
(AUTO)
• The vane moves intermittently between positions (1)
and (4). The vane stops for a brief period at posi-
tions (1) and (4).
(AUTO)
NOTE:
• Adjust the AIR FLOW direction using the remote controller. Moving the horizontal vane and vertical vane manually
can cause trouble.
COOL
1 • When the operation mode changes in "
DRY
position in each mode.
2
3
HEAT
4
COOL/DRY
At the start
of heating
operation
Horizontal
position
Horizontal position
• Immediately after the air conditioner starts operat-
ing, the vane stays at horizontal position. Once the
air from the indoor unit becomes sufficiently warm,
the vane moves to position (4).
• Once the air conditioner starts operating, the fan
VANE speed increases gradually as the air from the indoor
button.
unit gets warmer, and continues until the set speed
is finally reached.
At the start
of heating
After operation
around 0.5
to 1 hour
Position (1)
Horizontal
position
• Immediately after the air conditioner starts operat-
ing, the vane stays at horizontal position. Once the
air from the indoor unit becomes sufficiently warm,
the vane moves to the position corresponding to the
set direction of air flow.
• Once the air conditioner starts operating, the fan
speed increases gradually as the air from the indoor
unit gets warmer, and continues until the set speed
is finally reached.
• The vane moves intermittently between positions (2)
and (4). The vane stops for a brief period at positions
(2) and (4).
(1)
(4)
(AUTO)" mode, the horizontal vane is automatically changed to the
HEAT
When air
becomes
Very small
warm...
air flow
Position (4)
When air
becomes
Very small
warm...
Set position
air flow
(2)
(4)