Manual Operation (Cool, Dry, Heat/Fan); Air Flow Velocity And Direction Adjustment - Mitsubishi Electric MSC-A07YV Operating Instructions Manual

MANUAL OPERATION (COOL, DRY, HEAT/FAN)

˚C
CLOCK
AMPM
AMPM
TOO TOO
ON/OFF
WARM COOL
FAN STOP
I FEEL COOL
VANE START
HEAT
DRY
/FAN
MODE HR.
ECONO COOL MIN.
RESET CLOCK
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
I
When the set temperature is to be changed:
TOO
WARM
• Press the button to lower the temperature. One press lowers the temperature by about 1°C.
TOO
COOL
• Press the button to raise the temperature. One press raises the temperature by about 1°C.
In HEAT operation
• If the air conditioner absorbs too much heat from the air, it may be overloaded. Following a judgement made by the
microprocessor, the fan in the outdoor unit is automatically stopped to protect the air conditioner.
When the outdoor unit's fan is stopped, frost may form on the outdoor unit, but this is not a problem.
In DRY operation
• The temperature control (temperature setting) cannot be done.
• The room temperature is slightly lowered in this operation mode.
I
The details of the display on the indoor unit are explained on page 6.
NOTE:
When the ambient temperature is too high, the room temperature may not reach the set temperature since the unit
operates to cool the room under a high load.
Information for multi system air conditioner (Outdoor unit: MXZ series)
Multi system air conditioner (Outdoor unit: MXZ series) can connect two or more indoor units with one outdoor
unit. According to the capacity, two or more units can operate simultaneously.
• When you try to operate two or more indoor units with one outdoor unit simultaneously, one for the cooling and the other
for heating, the operation mode of the indoor unit that operates earlier is selected. The other indoor units that will start the
operation later cannot operate, indicating an operation state. (Refer to the table of Operation Indicator lamp on page 6.)
In this case, please set all the indoor units to the same operation mode.
• When indoor unit starts the operation while the defrosting of outdoor unit is being done, it takes a few minutes (max. 10
minutes) to blow out the warm air.
• In the heating operation, the indoor unit that does not operate may get warm or the sound of refrigerant flowing may be
heard. This is not a malfunction since the refrigerant continuously flows into the indoor unit that does not operate.
Description of "AUTO RESTART FUNCTION"
Refer to page 6.
To select the COOL, DRY or HEAT/FAN mode:
ON/OFF
1
Press the button.
2
Select the operation mode by pressing the
Each time this button is pressed, the operation mode is changed in sequence:
(I FEEL...) → (COOL) →
HEAT/FAN mode
Check the type of the air conditioner.
Type
COOL & HEAT
COOL ONLY
To stop operation:
ON/OFF
I
Press the button.
After the operation mode is set once, the operation starts in the same mode as
the one set previously from the next time by simply pressing the
MODE
button.
(DRY) → (HEAT/FAN)
Operation mode
HEAT
FAN
ON/OFF
button.
AIR FLOW VELOCITY A
AIR FLOW velocity and direction can be se
˚C
CLOCK
AMPM
AMPM
TOO TOO
ON/OFF
WARM COOL
FAN STOP
I FEEL COOL
VANE START
HEAT
DRY
/FAN
MODE HR.
ECONO COOL MIN.
RESET CLOCK
NOTE:
• In the cooling operation, when the air co
(4) or (5) for 1 hour, the AIR FLOW direc
from dropping.
• Adjust the vertical AIR FLOW direction using the
cause trouble.
• In the heating operation, if the air flow temperat
position is set to (1).
Auto air flow direction control operat
When the AUTO mode is selected with the
ton, the position of the horizontal vane is autom
cally set to correspond to the operation mode
effective operation.
(1) HEAT
• When the air flow temperature is too low, the a
blown out horizontally.
• When the air flow temperature rises, the air is bl
out downwards.
(2) COOL, DRY
The air is blown out horizontally.
(3) FAN
The air is blown out downwards.
I
To ch
Each
(Lo
• Us
• If
(
I
To ch
VANE
Each
seque
(A
SWING
Use the
Recomm
Use the
Use posi
and use
when ad
VANE