Page of 6

American Standard 2275.409 Installation Instructions Manual

Hide thumbs
   
COLONY SOFT
Centerset Lavatory Faucet
with Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet
with the Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with
the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these
instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL FAUCET
Apply a bead of putty along the edge of the underside of the FAUCET (1).
Insert FAUCET (1) and CABLE CONNECTOR (2) through center hole
of mounting surface. Fig. A.
From under side of mounting surface thread the two MOUNTING
NUTS (3) onto FAUCET SHANKS (4). Fig. B.
Center FAUCET (1) and hand tighten MOUNTING NUTS (3) to
secure FAUCET (1).
3
(HAND TIGHTEN)
4
Installation
Instructions
Channel Locks
Adjustable Wrench
Fig. B.
2275.409
2275.509
Plumbers' Putty or Caulking
Fig. A.
1
PUTTY
1
Certified to comply with ANSI A112.18.1
M 9 6 8 8 7 6 R e v. 1 . 2
Tubing Cutter
3
2

Advertising

   Related Manuals for American Standard 2275.409

   Summary of Contents for American Standard 2275.409

  • Page 1

    • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Certified to comply with ANSI A112.18.1 To ensure that your installation proceeds smoothly-please read these M 9 6 8 8 7 6 R e v.

  • Page 2

    POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN BODY DRAIN POP-UP (3). Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Fig. A. Fig. B. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain Fig.

  • Page 3

    ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig.

  • Page 4

    TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Ensure that AERATOR (3) is tightened completely. Operate HANDLES (1) to allow water flow. CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK.

  • Page 5: Troubleshooting Guide

    Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •...

  • Page 6

    To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

This manual also for:

2275.509

Comments to this Manuals

Symbols: 0
Latest comments: