Table of Contents
Advertisement
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MXM-5
Retain This
Manual for
Reference
09-01-05
OWNER'S
MANUAL
MARCY SMITH MACHINE
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MXM-5
IMPEX
Advertisement
Table of Contents
Related Manuals for Impex MARCY MXM-5
Summary of Contents for Impex MARCY MXM-5
- Page 1 Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MXM-5 Retain This Manual for Reference 09-01-05 OWNER'S MANUAL MARCY SMITH MACHINE MXM-5 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
-
Page 2: Table Of Contents
ORDERING PARTS...… 26 BEFORE YOU BEGIN Thank you for selecting the MARCY Smith Machine MXM-5 by IMPEX. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notices
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. - Page 4 WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
-
Page 5: Hardware Pack
HARDEWARE PACK... - Page 6 HARDEWARE PACK...
- Page 7 HARDEWARE PACK...
- Page 8 HARDEWARE PACK...
-
Page 9: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so. B.) Connect the Left &... - Page 10 DIAGRAM 1...
- Page 11 STEP 2 (See Diagram 2) A.) Attach the Rear Vertical Beam (#23) onto the Cross Brace (#20). Attach the Weight Glide Post (#22) to the Rear Vertical Beam and Cross Brace. Align the holes and secure them with two M10 x 2 ¾” Carriage Bolts (#93), (#99).
- Page 12 DIAGRAM2...
- Page 13 STEP 3 (See Diagram 3) A.) Attach the Butterfly Base (#24) and Butterfly Pulley Bracket (#33) to the Rear Vertical Beam (#23). Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#92), Washers (#82), and M10 Aircraft Nuts (#99). B.) Insert the pivot on the Right Butterfly (#26) through the hole on the Butterfly Base.
- Page 14 STEP 4 (See Diagram 4) A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting Sleeve (#38) in between the two Safety Stop Frames (#37). Align the holes and insert the Weight Bar (#39) into the Safety Stop Frame from one end through the Weight Lifting Sleeve to the other Safety Stop Frame on the opposite end.
- Page 15 CABLE LOOP DIAGRAM...
- Page 16 STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach a 124” Cable (#51) to the front opening on the Upper Frame (#21). Attach a Pulley (#74) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#87), two Ø 7/8” Bushings (#79), and one M10 Aircraft Nut (#99).
- Page 17 DIAGRAM 5...
- Page 18 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 79” Butterfly Cable (#52) to the clip on the Left Butterfly (#25). Draw the Cable to the left Butterfly Pulley Bracket (#33). B.) Attach a Pulley (#74) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two Washers (#82), and one M10 Aircraft Nut (#99).
- Page 19 STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one 124” Cable (#51) to the lower opening on the Rear Vertical Beam (#23). Attach a Pulley to the opening. Secure it with M10 x 2 3/8” Allen Bolt (#88), two Ø 1” Bushings (#78), and one M10 Aircraft Nut (#99).
- Page 20 STEP 8 (See Diagram 8) A.) Attach the Main Seat Support (#1) to the Front & Rear Stabilizers (#3 & #4). B.) Secure each end with two M10 x 3 1/8” Carriage Bolts (#94), one 4 ¾” Curve Bracket (#8), two ¾”...
- Page 21 STEP 9 (See Diagram 9) A.) Do not tighten all nuts and bolts until instructed to so. B.) Attach the Leg Developer Holder (#2) to the Main Seat Support. Secure it with two M10 x 3 1/8” Carriage Bolts (#94), one 6 ¼” Curve Bracket (#9), two M10 Aircraft Nuts (#99).
- Page 22 STEP-10 (See Diagram 10) A.) Attach the Leg Developer (#7) to the Leg Developer Holder (#2). Secure it with one M10 x 3 1/8” Allen Bolt (#90), two over tighten the nut and bolt. Make sure the Leg Developer is able to swivel. B.) Insert three Foam Tubes (#15) halfway through the holes on the Leg Developer Holder and Leg Developer.
- Page 23 STEP-11 (See Diagram 11) A.) Attach the Arm Curl Pad (#14) to the Arm Curl Stand (#13). Secure it with two M8 x ¾” Allen Bolts (#96) and 5/8” Washers (#81). B.) Insert the Arm Curl Stand into the opening on the Leg Developer Holder. Use a Lock Knob (#58) to secure it in position.
-
Page 24: Exploded Diagram
SMITH MACHINE EXPLODED DIAGRAM... -
Page 26: Parts List
PARTS LIST KEY NO. DESCRIPTION Main Seat Support Leg Developer Holder Front Stabilizer Rear Stabilizer Backrest Support Backrest Incline Support Leg Developer 4 ¾” Curve Bracket 6 ¼” Curve Bracket 10 Seat Pad 11 Bench Backrest Board 12 Ø 1” Spacer 13 Arm Curl Stand 14 Arm Curl Pad 15 Foam Tube... -
Page 27: Warranty
IMPEX LIMITED WARRANTY IMPEX warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.