Impex marcy premier home gym owner's manual premier (19 pages)
Summary of Contents for Impex MARCY MCB-347
Page 1
NOTE: Please read all instructions carefully before using this product Table of Contents MARCY CLASSIC Safety Notice MCB-347 COMBO BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MCB-347 Retain This Manual for Reference 06-25-08 OWNER'S MANUAL ®...
EXPLODED DIAGRAM... PARTS LIST...…. WARRANTY...…. ORDERING PARTS...…. BEFORE YOU BEGIN Thank you for selecting the MARCY CLASSIC MCB-347 COMBO BENCH ® by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory.
13. Maximum user weight: 300 lbs. 14. Maximum weight capacity on the uprights: 200 lbs. 16. Maximum weight capacity on the leg developer: 100 lbs. 17. Maximum weight capacity on the lat bar: 100 lbs. CARE AND MAINTENANCE 1-800-999-8899 www.impex-fitness.com info@impex-fitness.com IMPORTANT SAFETY NOTICE...
Page 4
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (SEE DIAGRAM 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span. Secure each end of Cross Brace with two M10 x 3 1/8”...
Page 8
STEP 2 (SEE DIAGRAM 2) A.) Attach the Front Stabilizer (#5) to the Main Seat Support (#3). Secure it with two M10 x ¾” Hex Bolts (#43), four ¾” Washers (#48), and two M10 Aircraft Nuts (#51). DO NOT tighten the nuts and bolts yet. B.) Attach the Main Seat Support (#3) to the Cross Brace (#2).
Page 9
STEP 3 (SEE DIAGRAM 3) A.) Attach the Leg Developer (#6) to the bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 ¾” Hex Bolt (#42), two Ø ¾” Washers (#48), and one M10 Aircraft Nut (#51). Do not over tighten the Nut and Bolt.
Page 10
STEP 4 (SEE DIAGRAM 4) A.) Attach the side holes on the Backrest Supports (#14) to the Pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#9). B.) Attach the Backrest Board (#19) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#47) and ½”...
Page 11
STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable (#38) to the Pulley (#36). Place the Pulley in the open slot on the Lat Bar Frame (#15). Secure the Pulley with one M10 x 2 1/8” Hex Bolt (#41), two Bushings (#37), and one M10 Aircraft Nut (#51).
PARTS LIST KEY NO. DESCRIPTION Rear Upright Beam Cross Brace Main Seat Support Diagonal Support Front Stabilizer Leg Developer Arm Curl Handle Foam Tube Backrest Adjustment Bar Arm Curl Stand Left Bar Catch Right Bar Catch Weight Holder Backrest Support Lat Bar Frame Lat Bar Bracket...
IMPEX authorized service center or for products used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.
Need help?
Do you have a question about the MARCY MCB-347 and is the answer not in the manual?
Questions and answers