Page 1
Table of Contents Safety Notice Hardware Pack Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MCB-849 Retain This Manual for Reference 09/25/08 OWNER'S MANUAL MARCY CLASSIC WEIGHT BENCH MCB-849 IMPEX 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com...
EXPLODED DIAGRAM... PARTS LIST... WARRANTY... ORDERING PARTS... BEFORE YOU BEGIN Thank you for selecting the MARCY CLASSIC WEIGHT BENCH MCB-849 by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee your complete satisfaction through direct assistance from our factory.
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.
Page 4
WARNING LABEL REPLACEMENT The Warning Labels shown here have been placed on the Rear Base Frame and Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-999- 8899 for replacement. Apply the labels in location shown...
ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended for two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach one Base Frame (#3) to the Rear Base Frame (#2). Attach an Upright Beam (#1) onto the Base Frame and Rear Base Frame.
Page 8
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#5) to the Rear Stabilizer (#6). Secure it with two M10 x 2 ¾” Carriage Bolts (#33), one 5 1/8” x 2 ¾” Bracket (#14), two Ø ¾” Washers (#41), and two M10 Aircraft Nuts (#44).
Page 9
STEP 3 (See Diagram 3) A.) Attach the pivot on the Leg Developer Holder (#7) to the open bracket on the Main Seat Support (#5). Attach the bottom of Leg Developer Holder to the Main Seat Support. Secure it with one M10 x 2 ¾” Carriage Bolt (#33) from front, one M10 x 2 ½” Allen Bolt (#37) from rear, two Ø...
Page 10
STEP 4 (See Diagram 4) A.) Attach the Backrest Board (#17) to the Backrest Supports (#8). Secure it with four M8 x 1 5/8” Allen Bolts (#38) and four Ø 5/8” Washers (#42). B.) Place the Seat Pad (#16) onto the seat bracket on Leg Developer Holder (#7). Secure it with one M8 x 1 5/8”...
Page 11
STEP 5 (See Diagram 5) A.) Attach two Ø 5/8” Bushings (#20) to the Leg Developer (#10). Attach the Leg Developer to the Leg Developer Holder (#7). Secure it with one M10 x 3 1/8” Allen Bolt (#36), two Ø ¾”...
Page 12
STEP 6 (SEE DIAGRAM 6) A.) Attach the Arm Curl Pad (#18) to the Arm Curl Bracket (#45). Secure it with two M8 x 5/8” Allen Bolts (#39) and two Ø 5/8” Washers (#42). B.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#11). Insert the M10 x 3 5/8” Allen Bolt (#35) through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket then secure the Bolt with two Ø...
PARTS LIST KEY NO. DESCRIPTION Upright Beam Rear Base Frame Base Frame Crutch Main Seat Support Rear Stabilizer Leg Developer Holder Backrest Support Incline Support Leg Developer Arm Curl Stand Incline Support Frame Foam Tube 5 1/8” x 2 ¾” Bracket 5 ½”...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.