Advertisement
Table of Contents
- 1 Installation and Operating Instructions
- 2 Table of Contents
- 3 Layout Options
- 4 Identification of Parts
- 5 Building Codes and Safety Standards
- 6 Piping and Gas Pressure Requirements
- 7 Installation Instructions
- 8 Log Placement
- 9 Operating Guidelines
- 10 Lighting Instructions
- 11 Trouble Shooting
- 12 Replacement Parts
- Download this manual
INSTALLER/CONSUMER RETAIN THIS APPLIANCE
MANUAL WITH THE INSTALLED APPLIANCE
INSTALLATION AND OPERATING INSTRUCTIONS
MODEL SF4224-TV TOP-VENT FIREPLACE
IMPORTANT! Read all instructions carefully before starting
installation. Failure to follow these instructions may result in
property damage, personal injury or possible loss of life.
WARNING: If the information in these
instructions is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
death.
– Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your
building;
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
• If you cannot reach your gas
supplier, call the fire department.
– Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
MANUFACTURED BY:
4301 WESTGROVE DRIVE
ADDISON TX. 75001
GOLDEN BLOUNT
SUPER-FIRE
CSA APPROVED FOR NATURAL GAS OR PROPANE GAS
■ The Flue Damper must be in the full
open position when burning the gas
logs.
■ This fireplace is to be burned only with
the gas log set supplied with the
fireplace. Burning other items could
cause a fire hazard or injury.
■ For best results, Natural Gas pressure
should be 7" to 12" W.C. and 11" W.C.
for Propane Gas.
■ To simulate real wood burning, the gas
burner is designed to burn a yellow
flame. It is normal for the logs to soot-
up. The soot can be easily removed
with a vacuum cleaner or soft brush.
■ Check the label on the firebox to
assure the proper gas type. Never
use anything but the correct gas type
for your fireplace.
This appliance complies with National
Safety and is tested and listed to ANSI
Z21.50A - 1998 as Vented Gas fireplaces.
Installation must conform to local codes.
In the absence of local codes, installation
must conform with the current National
Fuel Gas Code, ANSI Z223.1.
Massachusetts State Code requires
damper to be welded open or removed.
2/05
Advertisement
Table of Contents
Related Manuals for Golden Blount SUPER-FIRE SF4224-TV
Summary of Contents for Golden Blount SUPER-FIRE SF4224-TV
-
Page 1: Installation And Operating Instructions
MANUAL WITH THE INSTALLED APPLIANCE INSTALLATION AND OPERATING INSTRUCTIONS GOLDEN BLOUNT SUPER-FIRE MODEL SF4224-TV TOP-VENT FIREPLACE CSA APPROVED FOR NATURAL GAS OR PROPANE GAS IMPORTANT! Read all instructions carefully before starting installation. Failure to follow these instructions may result in property damage, personal injury or possible loss of life. -
Page 2: Table Of Contents
TABLE OF CONTENTS Section Layout Options ........................ 2 Identification of Parts ....................... 3 Building Codes and Safety Standards ................4 Piping and Gas Pressure Requirements ................. 5 Installation Instructions ....................6 Log Placement ........................ 9 Operating Guidelines ....................10 Lighting Instructions ...................... 12 Trouble Shooting ...................... -
Page 3: Identification Of Parts
SF4224-TV TOP-VENT FIREPLACE Damper Control Stand Offs Lever Valve Access Panel Outside Air Port INTERIOR VIEW Damper Control Lever Pan Burner Pilot Light Outside Air On/Off Switch Control Knob... -
Page 4: Building Codes And Safety Standards
Institute National Fuel Gas Code Z223.1 latest edition. GENERAL INFORMATION MODEL SF4224-TV IS A TOP-VENTED GAS FIREPLACE. IT IS DESIGNED TO BURN BY DRAWING COMBUSTION AIR FROM THE OUTSIDE AIR KIT THAT ATTACHES TO THE LEFT SIDE OF THE FIREPLACE. -
Page 5: Piping And Gas Pressure Requirements
GAS PIPING AND GAS PRESSURE REQUIREMENTS All gas piping must be installed to comply with local codes, or, in the absence of local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1. Unions in gas lines shall be of ground joint type. Compounds used on threaded joints of gas piping must be resistant to the action of liquefied petroleum gas. -
Page 6: Installation Instructions
Model SF4224-TV (with the use of the Outside Air Kit) can be installed in a bedroom (in the United States) which has a total volume of unconfined space appropriate to the particular installation. - Page 7 10' Rule of Thumb indicates a shorter chimney height. Note: Installations which will not allow the 10' rule to be followed must be submitted to Golden Blount Inc. for approval. 1-800-833-1139.
- Page 8 DUCT OUTER TERMINATION CASING RAIN CAP DUCT COLLAR CONTROL KNOB CAULKING WALL Connecting the Gas Line Figure 7.2 Consult local building codes before gas line installation. This gas fireplace is designed to accept a 3/8" male flare fitting attached to a 1/2" supply line. Have the gas line in- stalled by a qualified service person in accordance with all building codes.
-
Page 9: Log Placement
LOG PLACEMENT FOR MODEL# SF4224TBF LOG SET NOTE: FOR SF4224 STACK LOG PLACEMENT, SEE SHEET IN LOG CTN. Placement Instructions • Place the back bottom log (log #1) as shown in the Illustration above. It should be positioned on the back of the grate. -
Page 10: Operating Guidelines
OPTIONAL GLASS DOOR INSTALLATION 1. INSTALL GB DOOR TRACKS AND HINGE SPRINGS AS ILLUS- TRATED IN FIGURE 1 USING 6 SCREWS IN FIREPLACE CHASIS. 2. SCREW HANDLES ON TO DOORS. DOOR TRACK 3. INSTALL DOORS AS SHOWN IN FIGURE 2. (TOP) NOTE! HINGE SPRING... - Page 11 OPERATING GUIDELINES (CONT’D) Figure 11 When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to paint and lubricants used in the manufacturing process. The main burner flame characteristics are steady, not lifting or floating.
-
Page 12: Lighting Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. C. Use only your hand to push in or turn the gas A. - Page 13 TO TURN OFF GAS TO APPLIANCE TO TURN OFF GAS TO APPLIANCE 1. Open valve access door panel 2. Turn knob clockwise to pilot position then depress and continue turning to “OFF” 3. Close access door panel LPG (PROPANE) WARNING THE FOLLOWING WARNING APPLIES TO INSTALLATIONS USING L.P.
-
Page 14: Trouble Shooting
TROUBLE SHOOTING With proper installation and maintenance, your new Gas Fireplace should provide years of trouble-free service. If you do experience a problem, refer to the trouble shooting guide shown below. This guide will assist a qualified service person in the diagnosis of problems and the corrective action to be taken. - Page 15 TROUBLE SHOOTING (CONT’D) SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 2. Pilot will not stay lit A. Defective pilot 1. Check pilot, flame must after carefully following generator impinge on pilot generator. lighting instructions. Clean and or adjust pilot for maximum flame impingement on generator.
- Page 16 TROUBLE SHOOTING (CONT’D) SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 3. Pilot burning, no A. Damper control lever in 1. Set damper control lever gas burner, valve knob closed position to open position. “ON”, “ON/OFF” switch “ON”. B. “ON/OFF” switch or 1. Check ON/OFF switch wires defective and wires for proper connections.
-
Page 17: Replacement Parts
REPLACEMENT PARTS THE FOLLOWING REPLACEMENT PARTS ARE AVAILABLE FROM YOUR GOLDEN BLOUNT DEALER ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION TV-101 Gas Valve - N/G TV-115 Bottom Front Logs TV-102 Gas Valve - LP TV-116 Bottom Rear Log TV-103 “1/4””... - Page 18 OPERATING INSTRUCTIONS, GOLDEN BLOUNT WILL TAKE THE FOLLOWING ACTIONS: WITHIN THE FIRST YEAR FROM THE DATE OF INSTALLATION, GOLDEN BLOUNT SHALL, AT ITS OPTION REPLACE OR REPAIR ANY SUCH DEFECT IN MATERIAL OR WORKMANSHIP, AT GOLDEN BLOUNT’S EXPENSE, INCLUDING A REASONABLE LABOR ALLOWANCE AS DETER- MINED BY GOLDEN BLOUNT.
Need help?
Do you have a question about the SUPER-FIRE SF4224-TV and is the answer not in the manual?
Questions and answers
My pilot blew out on my SF4224-tv fireplace and I relit the pilot. The flute is open and I turned the gas electrical switch on and it won’t light. The panel door was closed before turning it on. I shut the electrical gas switch off and waited 3 minutes tried again and no luck
If the pilot light won't ignite after relighting on a Golden Blount SUPER-FIRE SF4224-TV fireplace, possible issues include:
1. Not holding the control knob long enough – The knob must be held down for a full minute after ignition.
2. Defective pilot generator – The flame must properly contact the generator. Clean or adjust the pilot for proper flame impingement.
3. Loose wire connections – Ensure wires from the generator to gas valve terminals are tight.
4. Low millivolt reading – Use a meter to check the generator. It should read at least 325 millivolts with the pilot lit and knob depressed.
5. Defective gas valve – If voltage is correct but the pilot still won’t stay lit, the valve may be faulty.
If the pilot still doesn’t stay lit after two tries, turn the gas control knob to “OFF” and contact a service technician or gas supplier.
This answer is automatically generated