GE ZBD3500 BB Installation Instructions Manual
Cleansensor dishwashers with optional trim kit
Hide thumbs
Also See for ZBD3500 BB:
- Use and care manual (28 pages) ,
- Use and care manual (24 pages) ,
- Use and care manual (24 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GE ZBD3500 BB
Summary of Contents for GE ZBD3500 BB
- Page 1 ® GE Monogram Installation Instructions with Optional Trim Kit Installation Instructions CleanSensor Dishwashers Models ZBD3500 BB ZBD3500 WW...
-
Page 2: Table Of Contents
Guide for warranty information. should immediately contact your dealer or builder. WARNINGS: For Monogram local service in your area, • This dishwasher must be installed to allow 1-800-444-1845. For Monogram Parts and Accessories, call for future removal from the enclosure if service is required. -
Page 3: Models Available
CleanSensor Dishwashers ZBD3500 WW Models White CleanSensor dishwasher Available ZBD3500 BB Black CleanSensor dishwasher Designed for versatility, the Monogram built- in dishwasher adapts easily to virtually any installation. A – 34" min. adjustable to Dimensions 35" max. & Clearances B – 24"... -
Page 4: Advance Planning
Design Information CleanSensor Dishwashers • These Monogram dishwashers are supplied • Tub flange trim is supplied to conceal any Advance as either a white or black model. Door and slight gap between the dishwasher and Preplanning access panels may be covered with custom adjacent 24"... -
Page 5: Side-By-Side Installation
Design Information CleanSensor Dishwashers • Two Monogram dishwashers may be Side-by-side installed side-by-side for greater capacity. Installation Custom Panel Kits • GPF700B, GPF700W, Trim Kits – Black or Optional • GPF425 Trim Kit – Provides for the installa- white replacement access panel only. -
Page 6: Installation Preparation
Installation Preparation CleanSensor Dishwasher Two Phillips head countertop mounting screws taped to Parts dishwasher. Supplied 90° elbow (3/8" NPT external thread on one end and opposite Materials You end to fit hot water supply line) Will Need: Thread seal tape (Not Supplied) UL listed wire nuts (3) Electrical Cable... -
Page 7: Single Dishwasher
Installation Preparation CleanSensor Dishwasher • The rough cabinet opening must be 24" Single min. deep and 24" wide. The opening Dishwasher height should be 34" min. and 35" max. This Wall Area must be Free of • The opening should be free of extraneous Pipes or wires 24"... -
Page 8: Water Supply
Installation Preparation CleanSensor Dishwasher Water Supply 4" 4" 1-1/2" Dia. 5" 5" Hole Shut-off Valve 6" 2" from 19" from Wall Cabinet 2" from Floor Cabinet Face • Hot water line may enter from either side, • Water connection is on the left side of the from the rear, or from the floor within the dishwasher. -
Page 9: Power Supply
Installation Preparation CleanSensor Dishwasher Power WARNING FOR PERSONAL SAFETY: Supply REMOVE HOUSE FUSE OR Alternate Receptacle OPEN CIRCUIT BREAKER Location BEFORE BEGINNING INSTALLATION. 18" 1-1/2" Dia. Hole (Max.) Receptacle 4" DO NOT USE AN EXTENSION CORD OR ADAPTER Location 4" 5"... -
Page 10: Prepare Drain Plumbing
Installation Preparation CleanSensor Dishwasher • Follow local codes and ordinances. Method 1 – Air Gap with Waste Tee or Disposer Prepare • Dishwasher drain hose must not exceed 10 Use this method when waste tee or disposer connection is less Drain feet in length for proper drainage. -
Page 11: Installation
Installation CleanSensor Dishwasher Step 1 CAUTION Check Do not remove wood base until you are ready to install the dishwasher. The dish- Door Balance washer will tip over when the door is opened. • Unlatch door and remove all foam and cardboard packaging. -
Page 12: Step 4, Remove Access Panel And Toekick
Installation CleanSensor Dishwasher • Remove the two screws below the access Step 4 panel and set aside. Back Out Remove 2 Screws • Loosen the two screws located between the Access Panel door and access panel. Do not attempt to remove these screws. -
Page 13: Step 7, Position Water Line And Power Supply
Installation CleanSensor Dishwasher Step 7 • Position the water supply line and wiring on the floor of the opening to avoid interfer- Position Water ence with base and components under dishwasher. Line And Power Supply Power Water Line Supply • Stand the dishwasher upright and move to Step 8 the front of the opening. -
Page 14: Step 10, Slide Dishwasher Into Cabinet
Installation CleanSensor Dishwasher • Slide dishwasher into the opening a few Step 10 CAUTION inches a time. As you proceed, pull the drain Slide Dishwasher DO NOT PUSH AGAINST hose through the opening and under the FRONT DOOR PANEL sink. Into Cabinet WITH KNEES. -
Page 15: Step 14 Connect Drain Line
Installation CleanSensor Dishwasher Method 1 – Air gap with waste tee or disposer Follow all local codes and ordinances. Step 14 Connect • The molded end of the drain line is de- signed to fit 5/8", 3/4" and 1" diameter Drain Line connections to air gap, waste tee or disposer. -
Page 16: Step 16, Installation Check List
Installation CleanSensor Dishwasher Check to be sure power is OFF. Check to be sure that wiring is secure Step 16 Open dishwasher door and remove all under the dishwasher and not pinched or Installation foam and cardboard packaging. in contact with door springs or other Remove literature package with Use &... -
Page 17: Gpf100 Trim Kit, Heavy Door Springs
GPF100 Trim Kit Heavy Door Springs For installation of a custom dishwasher door ools and Materials required: panel weighing 4 pounds to 8 pounds. • 1/4" socket driver • Phillips screwdriver To prevent electric shock, WARNING • Gloves to protect against sharp edges disconnect electrical power supply to dishwasher before changing panels. -
Page 18: And Access Panel Kits
GPF400/600/700 Series Trim Kits Door and Access Panel Kits GPF400B, Black door and access panels The GPF400 series trim kit is designed to GPF400W, White door and access panels provide a color change or to conceal minor GPF600B, Black door panel damage to original dishwasher door and GPF600W, White door panel access panels. - Page 19 GPF400/600/700 Series Trim Kits Door and Access Panel Change Step 2: Install New Door Panel Cover Note: The new door panel cover will completely cover the existing door. Do not remove the original door panel. For GPF400 and GPF600 Kits: •...
-
Page 20: Gpf400S, Stainless Steel Door And Access Panels
GPF400S Trim Kit Stainless Steel Door and Access Panels The GPF400S Stainless steel trim kit covers ools and Materials required: the existing door and access panel. • 1/4" socket driver • Phillips screwdriver This kit includes: • Electric drill • Door and access panel covers. •... - Page 21 GPF400S Trim Kit Stainless Steel Door and Access Panels Step 2: Install Stainless Door Panel Cover • Remove protective plastic film. • Drive 3 screws into the bottom of the panel • Tip door panel and slide up and under using a phillips head screwdriver.
-
Page 22: Gpf425, 1/4" Custom Panels
GPF425 Series Trim Kit 1/4" Custom Panels The GPF425 trim kits provide for the installa- GPF425B, Black Trim Kit tion of 1/4" thick custom door and access GPF425W, White Trim Kit panels. GPF425A, Almond Trim Kit This kit includes: • Left, right and bottom door trim ools and Materials required: •... - Page 23 GPF425 Series Trim Kit 1/4" Custom Panels Remove the protective plastic covering from Step 3: side trim pieces. Install Door Panel Trim And Custom Panel “Z” Trim A. Place bottom trim against the bottom of B. Slide “Z” shaped trim under the escutcheon. the door panel and drive center screw, then left and right screws.
- Page 24 GPF425 Series Trim Kit 1/4" Custom Panels • Place bottom trim against the bottom of the Step 4: access panel. Install Custom • Install color matched screw in the center, then left and right screws. Access Panel • Gently, bend both ends of the bottom trim upwards to form a “U”...
-
Page 25: Gpf475, 3/4" Custom Panels
GPF475 Series Trim Kit 3/4" Custom Panels The GPF475 Trim Kit provides for the installa- ools and Materials required: tion of 3/4" thick custom door and access • 1/4" socket driver panels with a typical 4" high toekick. • Phillips screwdriver This Kit includes: •... - Page 26 GPF475 Trim Kit 3/4" Custom Panels • Remove the two screws below the access Step 2: panel. Retain screws. Escutcheon Escutcheon Remove Lower • Loosen the two screws located between the door and the access panel. Do not attempt Access Panel to remove these screws.
- Page 27 GPF475 Trim Kit 3/4" Custom Panels Screw Holes for Vertical Step 3 (Typical) Wood Grain Remove (continued) Tape Covering Adhesive Strips Screw Holes for Horizontal Wood Grain Direction C. Remove the custom panel from the D. Determine the direction of the wood support.
- Page 28 GPF475 Trim Kit 3/4" Custom Panels • Drill 3 holes 3/16" dia. into the access panel Step 5 1/2" to 2" 1/2" to 2" as shown. Install Custom • Place the custom panel onto the access 1/2" to 2" assembly and mark hole locations. Center Line Panel To 3/16"...
-
Page 29: Gpf53, Mounting Brackets
GPF53 Mounting Kit Mounting Brackets Tools and materials required: The GPF53 mounting kit is to be used for • 5/16" nut driver attaching dishwashers to adjacent cabinets • Phillips screwdriver when countertops are stone or other materi- • Safety glasses als which will not accept screws. - Page 30 Notes...
- Page 31 Notes...
- Page 32 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845.
Need help?
Do you have a question about the ZBD3500 BB and is the answer not in the manual?
Questions and answers