User Manual of DS-9100HFI-ST Series DVR Regulatory Information FCC Information compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 3
User Manual of DS-9100HFI-ST Series DVR Safety Warnings and Cautions Please pay attention to the following warnings and cautions: Hazardous Voltage may be present: Special measures and precautions must be taken when using this device. Some potentials (voltages) on the device may present a hazard to the user.
Page 4
User Manual of DS-9100HFI-ST Series DVR Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency in your region.
User Manual of DS-9100HFI-ST Series DVR Preventive and Cautionary Tips Before connecting and operating your DVR, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Unit is designed for indoor use only.
User Manual of DS-9100HFI-ST Series DVR Product Key Features Compression PAL/NTSC adaptive video inputs. H.264 video compression with high reliability and superior definition. Each channel supports dual-stream. Main stream supports up to 4CIF resolution and sub stream supports up to CIF resolution.
Page 7
User Manual of DS-9100HFI-ST Series DVR Customization of tags, searching and playing back by tags. Locking and unlocking record files. Local redundant recording and capture. Searching and playing back record files by channel number, recording type, start time, end time, etc.
Page 8
User Manual of DS-9100HFI-ST Series DVR Remote system restart and shutdown. RS-232, RS-485 transparent channel transmission. Alarm and exception information can be sent to the remote host Remotely start/stop recording. Remotely start/stop alarm output. ...
User Manual of DS-9100HFI-ST Series DVR TABLE OF CONTENTS Product Key Features ......................5 C H A P T E R 1 ......................... 12 Introduction ..........................12 1.1 Front Panel ........................13 1.2 IR Remote Control Operations ..................16 1.3 USB Mouse Operation ....................18 1.4 Input Method Description .....................
Page 10
User Manual of DS-9100HFI-ST Series DVR 5.8 Configuring Redundant Recording and Capture ............67 5.9 Configuring HDD Group for Recording and Capture ........... 69 5.10 Files Protection ......................71 C H A P T E R 6 ......................... 74 Playback ............................. 74 6.1 Playing Back Record Files ....................
Page 11
User Manual of DS-9100HFI-ST Series DVR 9.2.6 Configuring Remote Alarm Host ..............144 9.2.7 Configuring Multicast ..................145 9.2.8 Configuring RTSP .................... 146 9.2.9 Configuring Server and HTTP Ports ..............147 9.2.10 Configuring Email ..................147 9.3 Checking Network Traffic ................... 150 9.4 Configuring Network Detection ..................
Page 12
User Manual of DS-9100HFI-ST Series DVR 13.2 Configuring General Settings ..................188 13.3 Configuring More Settings ..................189 13.4 Managing User Accounts ..................190 13.4.1 Adding a User ....................190 13.4.2 Deleting a User ....................192 13.4.3 Editing a User ....................193 13.4.4 Changing Password of Admin ................
User Manual of DS-9100HFI-ST Series DVR 1.1 Front Panel The front panel of DS-9100HFI-ST is shown in Figure 1.1. Figure 1.1 Front Panel Table 1.1 Description of Control Panel Buttons Name Function Description ALARM Alarm indicator turns red when a sensor alarm is detected.
Page 15
User Manual of DS-9100HFI-ST Series DVR Entering the Manual Record setting menu. In PTZ control settings, press REC/SHOT the REC/SHOT button and then you can call a PTZ preset by pressing Numeric button. The PLAY/AUTO button is used to enter the Playback menu. It is also...
Page 16
User Manual of DS-9100HFI-ST Series DVR event and exception settings will be invalid, but normal recording will still be available. Note: It is important to note that you must click the EDIT button on either the remote or front panel on a text field before you’re able to edit its content.
User Manual of DS-9100HFI-ST Series DVR 1.2 IR Remote Control Operations The DVR may also be controlled with the included IR remote control, shown in Figure 1.2. Note: Batteries (2×AAA) must be installed before operation. Figure 1.2 Remote Control The keys on the remote control closely resemble the ones found on the front panel. Referring to Figure 1.2, they Table 1.2 Description of the IR Remote Control Buttons...
Page 18
User Manual of DS-9100HFI-ST Series DVR MENU Button Same as the MENU/WIPER button on front panel. PREV Button Same as the PREV/FOCUS- button on front panel. DIRECTION/ENTER Same as the DIRECTION/ENTER buttons on front panel. Buttons Same as the PTZ/IRIS- button on front panel.
User Manual of DS-9100HFI-ST Series DVR 1.3 USB Mouse Operation A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this DVR. To use a USB mouse: Plug USB mouse into one of the USB interfaces on the front panel of the DVR.
User Manual of DS-9100HFI-ST Series DVR 1.5 Rear Panel Table 1.5 Description of DS-9100HFI-ST Rear Panel Item Description VIDEO IN BNC connector for analog video input. LOOP OUT BNC connector for video loop output. VIDEO SPOT OUT BNC connector for video output.
User Manual of DS-9100HFI-ST Series DVR 1.6 Starting Up and Shutting Down the DVR Purpose: Proper startup and shutdown procedures are crucial to expanding the life of the DVR. Before you start: Check that the voltage of the extra power supply is the same with the DVR’s requirement, and the ground connection is working properly.
Page 22
User Manual of DS-9100HFI-ST Series DVR • OPTION 2: By operating the front panel Press and hold the POWER button on the front panel for 3 seconds. Enter the administrator’s username and password in the dialog box for authentication. Click the Yes button.
User Manual of DS-9100HFI-ST Series DVR C H A P T E R 2 Getting Started...
Page 24
User Manual of DS-9100HFI-ST Series DVR By default, the Setup Wizard will start once the DVR has loaded, as shown in Figure 2.1. Figure 2.1 Start Wizard Interface Operating the Setup Wizard: The Setup Wizard can walk you through some important settings of the DVR. If you don’t want to use the Setup Wizard at this time, click the Cancel button.
Page 25
User Manual of DS-9100HFI-ST Series DVR Figure 2.3 Date and Time Settings After the time settings, click Next button which will take you back to the Network Setup Wizard window, as shown in Figure 2.4. Figure 2.4 Network Configuration Click Next button after you having configured the network parameters, which will take you to the HDD...
Page 26
User Manual of DS-9100HFI-ST Series DVR Figure 2.5 HDD Management To initialize the HDD, click the Init button. Initialization will remove all the data saved in the HDD. Click Next button to enter the Record Settings window, as shown in Figure 2.6.
Page 27
User Manual of DS-9100HFI-ST Series DVR Figure 2.7 Copy Record Settings Click OK to complete the startup Setup Wizard.
User Manual of DS-9100HFI-ST Series DVR 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The DVR will automatically enter Live View mode when powered on. It is also at the very top of the menu hierarchy, thus hitting the ESC many times (depending on which menu you’re on) will bring you to the Live View mode.
User Manual of DS-9100HFI-ST Series DVR 3.2 Operations in Live View Mode In live view mode, there are many functions provided. The functions are listed below. • Single Screen: show only one screen on the monitor. • Multi-screen: show multiple screens on the monitor simultaneously.
User Manual of DS-9100HFI-ST Series DVR 3.2.2 Using the Mouse in Live View Table 3.4 Mouse Operation in Live View Name Description Menu Enter the main menu of the system by right clicking the mouse. Single Screen Switch to the single full screen by choosing channel number from the dropdown list.
User Manual of DS-9100HFI-ST Series DVR feature will switch to the next set of displays. • Playback: Enter into Playback mode. • PTZ: Enter PTZ Control mode. • Main Monitor: Enter Main operation mode. Note: In the live view mode of the main output monitor, the menu operation is not available while in Aux output mode.
Page 33
User Manual of DS-9100HFI-ST Series DVR Image Settings icon can be selected to enter the Image Settings menu. There are four preset modes for selection according to the real situation. Below is the explanation for each mode. Indoor: the image is relatively smoother.
User Manual of DS-9100HFI-ST Series DVR 3.3 Adjusting Live View Settings Purpose: Live View settings can be customized according to different needs. You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Page 35
User Manual of DS-9100HFI-ST Series DVR Figure 3.7 Live View- Camera Order To set the camera order: Select View. Click the up and down button at each screen to select the channel you would like to display. Setting an ‘X’ means the channel will not be displayed.
User Manual of DS-9100HFI-ST Series DVR 3.4 Channel-zero Encoding Purpose: Sometimes you need to get a remote view of many channels in real time from web browser or CMS (Client Management System) software, in order to decrease the bandwidth requirement without affecting the image quality, channel-zero encoding is supported as an option for you.
User Manual of DS-9100HFI-ST Series DVR 3.5 Locking the System Purpose: After locking the system, the monitor turns to the live view mode and if you want to do some operation, you need to enter user name and password tog in again.
User Manual of DS-9100HFI-ST Series DVR 4.1 Configuring PTZ Settings Purpose: Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you set the PTZ camera. Before you start: Check that the PTZ and the DVR are connected properly through RS-485 interface.
User Manual of DS-9100HFI-ST Series DVR 4.2 Setting PTZ Presets, Patrols & Patterns Before you start: Please make sure that the presets, patrols and patterns should be supported by PTZ protocols. 4.2.1 Customizing Presets Purpose: Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place.
User Manual of DS-9100HFI-ST Series DVR 4.2.2 Calling Presets Purpose: This feature enables the camera to point to a specified position such as a window when an event takes place. Call preset in the PTZ setting interface: Steps: Enter the PTZ Control interface.
User Manual of DS-9100HFI-ST Series DVR Choose Camera in the list on the menu. Choose preset in the Preset list. 4.2.3 Customizing Patrols Purpose: Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point.
User Manual of DS-9100HFI-ST Series DVR Click OK to save the key point to the patrol. Repeat the above steps to add more key points. You can also delete all the key points by clicking the trash icon Figure 4.8KeyPoints Deletion 4.2.4 Calling Patrols...
User Manual of DS-9100HFI-ST Series DVR Calling preset in live view mode: Steps: Press PTZ control on the front panel or on the remote, or click PTZ Control icon on the quick setting toolbar, to show the PTZ control toolbar.
User Manual of DS-9100HFI-ST Series DVR Click , and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera. The movement of the PTZ is recorded as the pattern.
User Manual of DS-9100HFI-ST Series DVR Figure 4.13 PTZ Toolbar- Pattern 4.3 PTZ Control Toolbar In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or choose the PTZ Control icon to enter the PTZ toolbar.
User Manual of DS-9100HFI-ST Series DVR 5.1 Configuring Encoding Parameters Before you start: Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu>HDD>General) Figure 5.1 HDD- General Click Advance to check the storage mode of the HDD.
Page 49
User Manual of DS-9100HFI-ST Series DVR Figure 5.3 Record Encoding Encoding Parameters for Recording Select Record to configure. You can configure the stream type, the resolution, the video quality on demand. Click More to configure the pre-record, post-record time, expired time, redundant record/capture and whether you want to record audio.
Page 50
User Manual of DS-9100HFI-ST Series DVR Figure 5.4 Record Encoding- More Click Apply to save the settings. Click OK to back to the upper level menu. You can copy the settings to other channels by clicking Copy, if the setting can also be used for other channels.
User Manual of DS-9100HFI-ST Series DVR Figure 5.6 Capture Encoding Configure the parameters. Click Apply to save the settings. If the parameters can also be used to other channels, click Copy to copy the settings to other channels. Note: The interval is the time period between two capturing actions. You can configure all the parameters on this menu on your demand.
Page 52
User Manual of DS-9100HFI-ST Series DVR Figure 5.7 Record Schedule Choose the camera you want to configure. Select the check box after the Enable Schedule item. Click Edit. In the message box, you can choose the day to which you want to set schedule.
Page 53
User Manual of DS-9100HFI-ST Series DVR Figure 5.9 Copy Schedule to Other Days Click OK to save setting and back to upper level menu. Click Apply in the Record Schedule interface to save the settings. You can repeat steps 5)-8) to set schedule for other channels. If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy.
User Manual of DS-9100HFI-ST Series DVR 5.3 Configuring Motion Detection Record and Capture Purpose: Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the video can analyze it and do many actions to handle it. Enabling motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center and so on.
Page 55
User Manual of DS-9100HFI-ST Series DVR Figure 5.12 Motion Detection- Mask Click Handling, and the message box for channel information will pop up. Figure 5.13 Motion Detection Handling Select the channels which you want the motion detection event to trigger recording.
Page 56
User Manual of DS-9100HFI-ST Series DVR Figure 5.14 Record Schedule Check the checkbox after the Enable Schedule item. Click Edit. Figure 5.15 Edit Schedule- Motion Detection In the message box, you can choose the day to which you want to set schedule.
Page 57
User Manual of DS-9100HFI-ST Series DVR Figure 5.16 Edit Schedule- All Day To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
Page 58
User Manual of DS-9100HFI-ST Series DVR Figure 5.18 Copy Schedule to Other Channels...
User Manual of DS-9100HFI-ST Series DVR 5.4 Configuring Alarm Triggered Record and Capture Purpose: Follow the procedure to configure alarm triggered recording or capture. Steps: Enter the Alarm setting interface. Menu> Configuration> Alarm Figure 5.19 Alarm Settings Click Alarm Input.
Page 60
User Manual of DS-9100HFI-ST Series DVR Figure 5.21 Alarm Handling Choose the alarm triggered recording channel. Check the checkbox to select channel. Click Apply to save settings. Click OK to back to the upper level menu. Repeat the above steps to configure other alarm input parameters.
Page 61
User Manual of DS-9100HFI-ST Series DVR Figure 5.23 Record Schedule Click Edit. Set the Type to Alarm In the message box, you can choose the day to which you want to set schedule. To schedule an all-day recording, check the checkbox after the All Day item.
User Manual of DS-9100HFI-ST Series DVR 5.5 Manual Record and Continuous Capture Purpose: Follow the steps to set parameters for the manual record and continuous capture. Using manual record and continuous capture, you don’t need to set a schedule for recording or capture.
Page 63
User Manual of DS-9100HFI-ST Series DVR Figure 5.25 Continuous Capture Click the status button before camera number to change Disable continuous capture. Click the status button to change Note: After rebooting, all the continuous capture will be canceled.
User Manual of DS-9100HFI-ST Series DVR 5.6 Configuring Holiday Record and Capture Purpose: Follow the steps to configure the record or capture schedule on holiday for that year. You may want to have different plan for recording and capture on holiday.
Page 65
User Manual of DS-9100HFI-ST Series DVR Set the start and end date. Click Apply to save settings. Click OK to exit the Edit interface. Enter Record/Capture Schedule settings interface. Menu> Record> Schedule Select Record/Capture. Check the checkbox after Enable Schedule.
User Manual of DS-9100HFI-ST Series DVR 5.7 Configuring Other Recording and Capture Types Purpose: Other recording and capture types refer to the Motion | Alarm (motion or alarm) and Motion & Alarm triggered recording and capture. For motion detection and alarm recording and capture, please refer to Chapter 5.3 and Chapter 5.4 .
Page 67
User Manual of DS-9100HFI-ST Series DVR Figure 5.30 Edit Schedule- Motion| Alarm To schedule an all-day recording, select the checkbox after the All Day item To arrange other schedule, leave the All Day checkbox blank and set the Start/End time.
User Manual of DS-9100HFI-ST Series DVR 5.8 Configuring Redundant Recording and Capture Purpose: Enabling redundant recording and capture, which means saving the record files and captured pictures not only in the R/W HDD but also in the redundant HDD, will effectively enhance the data safety and reliability. .
Page 69
User Manual of DS-9100HFI-ST Series DVR Note: You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property to Redundant. For detailed information, please refer to Chapter 10.4 Managing HDD Group. There should be at least another HDD which is in Read/Write status.
User Manual of DS-9100HFI-ST Series DVR 5.9 Configuring HDD Group for Recording and Capture Purpose: You can group the HDDs and save the record files and captured pictures in certain HDD group. Steps: Enter HDD setting interface. Menu>HDD Figure 5.35 HDD General Select Advanced on the left bar.
Page 71
User Manual of DS-9100HFI-ST Series DVR Figure 5.36 HDD Advanced Choose Group number in the dropdown list of Record on HDD Group Check the channels you want to save in this group. Click Apply to save settings. Note: After you having configured the HDD groups, you can configure the Recording and...
User Manual of DS-9100HFI-ST Series DVR 5.10 Files Protection Purpose: You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten. Protect file by locking the record files: Steps: Enter Playback setting interface.
Page 73
User Manual of DS-9100HFI-ST Series DVR Find the record files you want to protect, and then click the icon which will turn to indicating that the file is locked. Note: Only the record files with size bigger than 1GB can be locked, otherwise it can’t be protected by locking it.
Page 74
User Manual of DS-9100HFI-ST Series DVR Figure 5.41 HDD General- Editing Note: To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter Managing 10.4 HDD Group. Set the HDD to Read-only. Click OK to save settings and back to the upper level menu.
User Manual of DS-9100HFI-ST Series DVR 6.1 Playing Back Record Files 6.1.1 Playing Back by Channel Purpose: Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. Instant playback by channel:...
Page 77
User Manual of DS-9100HFI-ST Series DVR Figure 6.2 Right-click Menu under Live View Front Panel: press PLAY button to play back record files of the channel under single-screen live view mode. Under multi-screen live view mode, the recorded files of the top-left channel will be played back.
Page 78
Figure 6.4 All-day Playback Interface with Channel List Dates marked in colors: : No record files in this day. : There is record file(s) in this day (not current day). : Mouse cursor is located. Figure 6.5 Toolbar of All-day Playback Table 6.1 Detailed Explanation of All-day-playback Toolbar Button Operation...
User Manual of DS-9100HFI-ST Series DVR 6.1.2 Playing Back by Time Purpose: Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. Steps: Enter playback interface. Menu>Playback Set search conditions and click the Playback button to enter Playback interface.
User Manual of DS-9100HFI-ST Series DVR Figure 6.8 Toolbar of Playback by Time Table 6.2 Detailed Explanation of Playback-by-time Toolbar Button Operation Button Operation Button Operation Button Operation Audio on/Mute Start/Stop clipping 30s forward 30s reverse Add default tag Add customized tag...
Page 81
User Manual of DS-9100HFI-ST Series DVR Figure 6.9 Normal Video Search Choose a record file you want to play back. If there is only one channel in the search result, pressing button takes you to Full-screen Playback interface of this channel.
Page 82
User Manual of DS-9100HFI-ST Series DVR Figure 6.11 Select Channels for Synchronous Playback Synchronous Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6.12 4-ch Synchronous Playback Interface The hidden list of recorded files displays by moving the mouse to the right of the playback interface.
User Manual of DS-9100HFI-ST Series DVR Figure 6.13 4-ch Synchronous Playback Interface with Video List Figure 6.14 Toolbar of Normal Playback Table 6.3 Detailed Explanation of Normal Playback Toolbar Button Operation Button Operation Button Operation Button Operation Audio on/Mute Start/Stop clipping...
Page 84
User Manual of DS-9100HFI-ST Series DVR Steps: Enter the playback interface. Menu>Playback Select Event tab to enter the Event Playback interface. Select Alarm Input as the event type. Click Search button to enter the Search Result interface. Figure 6.15 Video Search by Alarm Input If you want to play back recorded files associated with motion detection, choose Motion as event type and click Search button to enter the Search Result interface.
Page 85
User Manual of DS-9100HFI-ST Series DVR Figure 6.17 Result of Video Search by Alarm Input Click Details button to view detailed information of the record file, e.g. start time, end time, file size, etc. Figure 6.18 Event Details Interface Playback interface.
Page 86
User Manual of DS-9100HFI-ST Series DVR Figure 6.19 Interface of Playback by Event The hidden list of events will be displayed by moving the mouse to the right of the playback interface. Figure 6.20 Playback Interface with Alarm Input List Figure 6.21 Toolbar of Playback by Event...
User Manual of DS-9100HFI-ST Series DVR Previous event Next event Event search Exit Video type Hide Progress bar Note: 1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames.
Page 88
User Manual of DS-9100HFI-ST Series DVR Figure 6.23 Tag Management Interface Steps: Enter Playback interface. Menu>Playback Press Tag tab to enter Playback by Tag interface. Choose channels, tag type and time, and press Search to enter Search Result interface. Note: Two tag types are selectable: All and Tag Keyword.
Page 89
User Manual of DS-9100HFI-ST Series DVR Figure 6.25 Result of Video Search by Tag Playback by tag. Choose a tag and press button to play back the related record file. Figure 6.26 Interface of Playback by Tag The hidden list of tags will be displayed by moving the mouse to the right of the playback interface.
User Manual of DS-9100HFI-ST Series DVR Figure 6.27 Interface of Playback by Tag with Video List Figure 6.28 Toolbar of Playback by Tag Table 6.5 Detailed Explanation of Playback-by-tag Toolbar Button Operation Button Operation Button Operation Button Operation Audio on/Mute...
Page 91
User Manual of DS-9100HFI-ST Series DVR Enter Log Search interface. Menu>Maintenance>Log Search Set search time and type and press Search button. Figure 6.29 System Log Search Interface Choose a log with record file and press button to enter Playback interface.
Page 92
User Manual of DS-9100HFI-ST Series DVR Figure 6.30 Interface of Playback by Log...
User Manual of DS-9100HFI-ST Series DVR 6.2 Auxiliary Functions of Playback 6.2.1 Playing Back Frame by Frame Purpose: Play video files frame by frame, in order to check image details of the video when abnormal events happen. Steps: • Using a Mouse: Go to Playback interface and click button until the speed changes to Single frame.
Page 94
User Manual of DS-9100HFI-ST Series DVR Figure 6.32 Right-click Menu under Playback You can press button to set the full screen as target searching area. After drawing area(s), press button to execute smart search in this area. Note: Multi-area and full-screen searching modes are supported.
User Manual of DS-9100HFI-ST Series DVR Figure 6.34 Smart Search Result with Video List Figure 6.35 Toolbar of Smart Search Playback Table 6.6 Detailed Explanation of Smart-search-playback Toolbar Button Operation Button Operation Button Operation Button Operation Audio on/Mute Start/Stop clipping...
Page 96
User Manual of DS-9100HFI-ST Series DVR interface. Move the red rectangle and the image within it will be quadrupled. Figure 6.36 Draw Area for Digital Zoom Figure 6.37 Right-click Menu under Playback The right-click menu: Table 6.7 Detailed Explanation of Right-click Menu under Playback Note: This menu differs slightly from one playback interface to another.
User Manual of DS-9100HFI-ST Series DVR 6.3 Picture Playback Purpose: Search and view captured pictures stored in HDD. Steps: Enter Playback interface. Menu>Playback Choose Picture tab. Set channel, picture type and time and press Search button to enter Search Result interface.
Page 98
User Manual of DS-9100HFI-ST Series DVR The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6.40 Picture Playback Interface The hidden list of captured pictures will be displayed by moving the mouse to the right of the playback interface.
User Manual of DS-9100HFI-ST Series DVR 7.1 Backing up Record Files 7.1.1 Quick Export Purpose: Export record files to backup device(s) quickly. Steps: Enter Video Export interface. Choose the channel(s) you want to back up and press Quick Export button.
Page 101
User Manual of DS-9100HFI-ST Series DVR Figure 7.2 Quick Export using USB1-1 Stay in the Exporting interface until all record files are exported. Figure 7.3 Export Finished Check backup result. Choose the record file in Export interface and press button to check it.
User Manual of DS-9100HFI-ST Series DVR 7.1.2 Backing up by Normal Video Search Purpose: The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB writer), SATA writer and e-SATA HDD. Backup using USB flash drives and USB HDDs Steps: Enter Export interface.
Page 103
User Manual of DS-9100HFI-ST Series DVR Export. Click Export button and start backup. Note: If the inserted USB device is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drives or USB HDDs via the device.
Page 104
User Manual of DS-9100HFI-ST Series DVR Figure 7.9 Checkup of Export Result using USB Flash Drive Backup using USB writer and SATA writer Steps: Enter Export interface. Menu>Export>Normal Set search condition and press Search button to enter the search result interface.
Page 105
User Manual of DS-9100HFI-ST Series DVR Figure 7.11 Result of Normal Video Search for Backup Export. Click Export button and start backup. Note: If the inserted USB writer or SATA writer is not recognized: • Click the Refresh button. •...
Page 106
User Manual of DS-9100HFI-ST Series DVR Figure 7.13 Export Finished Check backup result. Choose the record file in Export interface and press button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7.14 Checkup of Export Result using USB Writer...
Page 107
User Manual of DS-9100HFI-ST Series DVR Figure 7.15 Normal Video Search for Backup Select record files you want to back up. Press button to play the record file if you want to check it. Tick record files you want to back up.
Page 108
User Manual of DS-9100HFI-ST Series DVR Figure 7.17 Export by Normal Video Search Using eSATA HDD Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7.18 Export Finished Check backup result. Choose the record file in Export interface and press button to check it.
User Manual of DS-9100HFI-ST Series DVR 7.1.3 Backing up by Event Search Purpose: Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Quick Backup and Normal Backup are supported.
Page 110
User Manual of DS-9100HFI-ST Series DVR Figure 7.21 Result of Event Search Click Details button to view detailed information of the record file, e.g. start time, end time, file size, etc. Note: The size of the currently selected files is displayed in the lower-left corner of the window.
Page 111
User Manual of DS-9100HFI-ST Series DVR Figure 7.23 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7.24 Export Finished Check backup result. Note: The Player player.exe will be exported automatically during record file export.
User Manual of DS-9100HFI-ST Series DVR 7.1.4 Backing up Video Clips Purpose: You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Steps: Enter Playback interface.
Page 113
User Manual of DS-9100HFI-ST Series DVR Figure 7.28 Export Video Clips Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7.29 Export Finished Check backup result. Note: The Player player.exe will be exported automatically during record file export.
User Manual of DS-9100HFI-ST Series DVR 7.2 Backing up Pictures Purpose: Back up pictures using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Steps: Enter Export interface. Menu>Export>Picture Select channel(s), image type, start time and end time, and click Search button to enter the Search Result interface.
Page 115
User Manual of DS-9100HFI-ST Series DVR Export. Press Export button and start backup. Figure 7.33 Export Pictures Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7.34 Export Finished Check backup result.
User Manual of DS-9100HFI-ST Series DVR 7.3 Managing Backup Devices Management of USB flash drives, USB HDDs and eSATA HDDs. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and press Search button to enter Search Result interface.
Page 117
User Manual of DS-9100HFI-ST Series DVR Select a record file in the backup device and press button to play it. Press Format button to format the backup device. Note: If the inserted USB device is not recognized: • Click the Refresh button.
Page 118
User Manual of DS-9100HFI-ST Series DVR Figure 7. 40 Result of Normal Video Search for Backup Backup device management. Press Erase button if you want to erase the files from a re-writable CD/DVD. Note: There must be a re-writable CD/DVD when you make this operation.
User Manual of DS-9100HFI-ST Series DVR 8.1 Setting up Motion Detection Steps: Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection. Menu> Camera> Motion Figure 8.1 Motion Detection Setup Interface Set up detection area and sensitivity.
Page 121
User Manual of DS-9100HFI-ST Series DVR Click Trigger Channel tab and select one or more channels which will start to record/capture or become full-screen monitoring when motion alarm is triggered. Figure 8.3 Set Trigger Camera of Motion Detection Set up arming schedule of the channel.
Page 122
User Manual of DS-9100HFI-ST Series DVR Figure 8.5 Copy Settings of Motion Detection...
User Manual of DS-9100HFI-ST Series DVR 8.2 Setting up Sensor Alarms Purpose: Set up handling method of an external sensor alarm. Steps: Enter Alarm Settings of System Configuration and select an alarm input. Menu> Configuration> Alarm Select Alarm Input tab to enter Alarm Input Settings interface.
Page 124
User Manual of DS-9100HFI-ST Series DVR Note: Time periods shall not be repeated or overlapped. Select Handling tab to set up alarm response actions of the alarm input (please refer to Chapter 8.6). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days.
Page 125
User Manual of DS-9100HFI-ST Series DVR If you want to set handling method of another alarm input, repeat the above steps or just copy the above settings to it. Figure 8.10 Copy Settings of Alarm Input...
User Manual of DS-9100HFI-ST Series DVR 8.3 Detecting Video Loss Purpose: Detect video loss of a channel and take alarm response action(s). Steps: Enter Video Loss interface of Camera Management and select a channel you want to detect. Menu> Camera> Video Loss Figure 8.11 Video Loss Setup Interface...
User Manual of DS-9100HFI-ST Series DVR Note: Time periods shall not be repeated or overlapped. Figure 8.13 Set Arming Schedule of Video Loss Select Handling tab to set up alarm response action of video loss (please refer to Chapter 8.6).
Page 128
User Manual of DS-9100HFI-ST Series DVR tampering. Menu> Camera> Tamper-proof Figure 8.15 Tamper-proof Setup Interface Set up the video tampering handling method of the channel. Check the checkbox of “Enable Video Tampering”. Drag the sensitivity bar and choose a proper sensitivity level. Use the mouse to draw an area you want to detect video tampering.
Page 129
User Manual of DS-9100HFI-ST Series DVR Figure 8.17 Set Arming Schedule of Video Tampering Select Handling tab to set up alarm response actions of video tampering alarm (please refer to Chapter 8.6). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days.
User Manual of DS-9100HFI-ST Series DVR 8.5 Handling Exceptions Purpose: Exception settings refer to the handling method of various exceptions, e.g. • HDD Full: The HDD is full. • HDD Error: Writing HDD error or unformatted HDD. • Network Disconnected: Disconnected network cable.
User Manual of DS-9100HFI-ST Series DVR 8.6 Setting Alarm Response Actions Purpose: Take alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Upload Picture to FTP, Trigger Alarm Output and Send Email.
Page 132
User Manual of DS-9100HFI-ST Series DVR Trigger Alarm Output Trigger an alarm output when an alarm is triggered. Enter Alarm Output interface. Menu> Configuration> Alarm> Alarm Output Select an alarm output and set alarm name and dwell time. Press Schedule button to set the arming schedule of alarm output.
Page 133
User Manual of DS-9100HFI-ST Series DVR You can also copy the above settings to another channel. Figure 8.22 Copy Settings of Alarm Output...
User Manual of DS-9100HFI-ST Series DVR 8.7 Triggering or Clearing Alarm Output Manually Purpose: Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell time of an alarm output, the alarm can be cleared only by pressing Clear button in the following interface.
User Manual of DS-9100HFI-ST Series DVR 9.1 Configuring General Settings Purpose: Network settings must be properly configured before you operate DVR over network. Steps: Enter the Network Settings interface. Menu > Configuration > Network Figure 9.1 Network Settings Interface Select the General tab.
Page 137
User Manual of DS-9100HFI-ST Series DVR Figure 9.2 Multi-address Working Mode Load Balance Mode: By using the same IP address, and two NIC cards share the load of the total bandwidth , which enables the system to provide two Gigabit network capacity.
User Manual of DS-9100HFI-ST Series DVR Figure 9.4 Net Fault-tolerance Working Mode 9.2 Configuring Advanced Settings 9.2.1 Configuring PPPoE Settings Purpose: Your DVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). Steps: Enter the Network Settings interface. Menu > Configuration > Network Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 9.5.
User Manual of DS-9100HFI-ST Series DVR Note: The User Name and Password should be assigned by your ISP. Figure 9.6 PPPoE Settings Interface Click the Apply button to save and exit the interface. After successful settings, the system asks you to reboot the device to enable the new settings, and the PPPoE dial-up is automatically connected after reboot.
Page 140
User Manual of DS-9100HFI-ST Series DVR Figure 9.7 DDNS Settings Interface Check the DDNS checkbox to enable this feature. Select DDNS Type. Four different DDNS types are selectable: IPServer, DynDNS, PeanutHull and NO-IP. • IPServer: Enter Server Address for IPServer.
Page 141
User Manual of DS-9100HFI-ST Series DVR Figure 9.9 DynDNS Settings Interface • PeanutHull: Enter User Name and Password obtained from the PeanutHull website. Figure 9.10 Peanut Hull Settings Interface • NO-IP: Enter the account information in the corresponding fields. Refer to the DynDNS settings.
User Manual of DS-9100HFI-ST Series DVR Figure 9.11 NO-IP Settings Interface Click the Apply button to save and exit the interface. 9.2.3 Configuring NTP Server Purpose: A Network Time Protocol (NTP) Server can be configured on your DVR to ensure the accuracy of system date/time.
User Manual of DS-9100HFI-ST Series DVR minute. • NTP Server: IP address of NTP server. • NTP Port: Port of NTP server. Click the Apply button to save and exit the interface. Note: The time synchronization interval can be set from 1 to 10080min, and the default value is 60min. If the DVR is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44).
User Manual of DS-9100HFI-ST Series DVR Figure 9.14 Configure FTP Settings Directory: In the Directory field, you can select the Root Directory, Parent directory and secondary directory. When the Parent Directory is selected, you have the option to use the Device Name, Device No or Device IP for the name of the directory;...
User Manual of DS-9100HFI-ST Series DVR Check the SNMP checkbox to enable this feature. Configure the SNMP settings. Figure 9.16 Configure SNMP Settings Click the Apply button to save and exit the interface. Note: Before setting the SNMP, please download the SNMP software and manage to receive the device information via SNMP port.
User Manual of DS-9100HFI-ST Series DVR Figure 9.17 More Settings Interface Enter Alarm Host IP and Alarm Host Port in the text fields. The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance Software (e.g., iVMS-4000) is installed, and the Alarm Host Port must be the same as the...
User Manual of DS-9100HFI-ST Series DVR Menu > Configuration > Network Select the More Settings tab to enter the More Settings interface, as shown in Figure 9.17. Set Multicast IP, as shown in Figure 9.19. When adding a device to the Network Video Surveillance Software, the multicast address must be the same as the DVR’s multicast IP.
User Manual of DS-9100HFI-ST Series DVR Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can change it according to different requirements. Click the Apply button to save and exit the menu.
Page 149
User Manual of DS-9100HFI-ST Series DVR Steps: Enter the Network Settings interface. Menu > Configuration > Network Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network Settings menu, as shown in Figure 9.22.
Page 150
User Manual of DS-9100HFI-ST Series DVR Enable SSL(optional): Click the checkbox to enable SSL if required by the SMTP server. Sender: The name of sender. Sender’s Address: The Email address of sender. Select Receivers: Select the receiver. Up to 3 receivers can be configured.
User Manual of DS-9100HFI-ST Series DVR 9.3 Checking Network Traffic Purpose: You can check the network traffic to obtain real-time information of DVR such as linking status, MTU, sending/receiving rate, etc. Steps: Enter the Network Traffic interface. Menu > Maintenance > Net Detect Figure 9.25 Network Traffic Interface...
User Manual of DS-9100HFI-ST Series DVR 9.4 Configuring Network Detection Purpose: You can obtain network connecting status of DVR through the network detection function, including network delay, packet loss, etc. 9.4.1 Testing Network Delay and Packet Loss Steps: Enter the Network Traffic interface.
Page 153
User Manual of DS-9100HFI-ST Series DVR By connecting the DVR to network, the captured network data packet can be exported to USB-flash disk, SATA/eSTATA CD-RW and other local backup devices. Steps: Enter the Network Traffic interface. Menu > Maintenance > Net Detect Click the Network Detection tab to enter the Network Detection interface.
User Manual of DS-9100HFI-ST Series DVR 10.1 Initializing HDDs Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your DVR. Steps: Enter the HDD Information interface. Menu > HDD>General. Figure 10.1 HDD Information Interface Select HDD to be initialized.
Page 156
User Manual of DS-9100HFI-ST Series DVR After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal. Figure 10.4 HDD Status Changes to Normal Note: Initializing the HDD will erase all data on it.
User Manual of DS-9100HFI-ST Series DVR 10.2 Managing Network HDD Purpose: You can add the allocated NAS or disk of IP SAN to DVR, and use it as network HDD. Steps: Enter the HDD Information interface. Menu > HDD>General. Figure 10.5 HDD Information Interface Click the Add button to enter the Add NetHDD interface, as shown in Figure 10.6.
Page 158
User Manual of DS-9100HFI-ST Series DVR 1) Enter the NetHDD IP address in the text field. 2) Enter the NetHDD Directory in the text field. 3) Click the OK button to add the configured NAS disk. Note: Up to 8 NAS disks can be added.
Page 159
User Manual of DS-9100HFI-ST Series DVR Figure 10.9 Initialize Added NetHDD...
User Manual of DS-9100HFI-ST Series DVR 10.3 Managing eSATA Purpose: When there is an external eSATA device connected to DVR, you can configure eSATA for the use of Record/Capture or Export, and you can manage the eSATA in the DVR.
Page 161
User Manual of DS-9100HFI-ST Series DVR Figure 10.11 Initialize Added NetHDD...
User Manual of DS-9100HFI-ST Series DVR 10.4 Managing HDD Group 10.4.1 Setting HDD Groups Purpose: Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Steps: Enter the Storage Mode interface.
User Manual of DS-9100HFI-ST Series DVR Figure 10.14 Local HDD Settings Interface Select the Group number for the current HDD. Note: The default group No. for each HDD is 1. Click the OK button to confirm the settings. Figure 10. 15 Confirm HDD Group Settings In the pop-up Attention box, click the Yes button to finish the settings.
Page 164
User Manual of DS-9100HFI-ST Series DVR Figure 10.16 Set HDD Property Set the HDD property to R/W, Read-only or Redundancy. Click the OK button to save the settings and exit the interface. In the HDD Information menu, the HDD property will be displayed in the list.
User Manual of DS-9100HFI-ST Series DVR 10.5 Configuring Quota Mode Purpose Each camera can be configured with allocated quota for the storage of recorded files or captured pictures. Steps Enter the Storage Mode interface. Menu > HDD > Advanced Set the Mode to Quota, as shown in Figure 10.17.
Page 166
User Manual of DS-9100HFI-ST Series DVR to enter the Copy Camera menu, as shown in Figure 10.19. Figure 10.19 Copy Settings to Other Camera(s) Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of Analog to select all cameras.
User Manual of DS-9100HFI-ST Series DVR 10.6 Checking HDD Status Purpose: You may check the status of the installed HDDs on DVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface Steps: Enter the HDD Information interface.
Page 168
User Manual of DS-9100HFI-ST Series DVR Figure 10.21 View HDD Status (2)
User Manual of DS-9100HFI-ST Series DVR 10.7 Checking S.M.A.R.T Information Purpose: The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect report on various indicators of reliability in the hopes of anticipating failures. Steps: Enter the S.M.A.R.T Settings interface.
User Manual of DS-9100HFI-ST Series DVR 10.8 Configuring HDD Error Alarms Purpose: You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. Steps: Enter the Exception interface. Menu > Configuration > Exceptions Select the Exception Type to HDD Error from the dropdown list.
User Manual of DS-9100HFI-ST Series DVR 11.1 Configuring OSD Settings Purpose: You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc. Steps: Enter the OSD Configuration interface. Menu > Camera > OSD Select the camera to configure OSD settings.
User Manual of DS-9100HFI-ST Series DVR Select the camera (s) to be configured with the same OSD settings. You can also click the checkbox of Analog to select all cameras. Click the OK button to finish the Copy settings and back to the OSD Configuration interface.
User Manual of DS-9100HFI-ST Series DVR Figure 11. 4 Set Privacy Mask Area You can click the Copy button to copy the privacy mask settings of the current camera to other cameras. Please refer to step 7 of Chapter 11.1 Configuring OSD Settings.
Page 175
User Manual of DS-9100HFI-ST Series DVR Figure 11.6 Configure Customized Image Settings You can click the Copy button to copy the image settings of the current camera to other cameras. Please refer to step 7 of Chapter 11.1 Configuring OSD Settings.
User Manual of DS-9100HFI-ST Series DVR 12.1 Viewing System Information 12.1.1 Viewing Device Information Steps: Enter the System Information interface. Menu > Maintenance > System Info Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No.
User Manual of DS-9100HFI-ST Series DVR Figure 12.2 Camera Information Interface 12.1.3 Viewing Record Information Steps: Enter the System Information interface. Menu > Maintenance > System Info Click the Record tab to enter the Record Information menu to view the recording status encoding parameters of each camera, as shown in Figure 12.3.
User Manual of DS-9100HFI-ST Series DVR Menu > Maintenance > System Info Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure 12.4. Figure 12.4 Alarm Information Interface 12.1.5 Viewing Network Information Steps: Enter the System Information interface.
User Manual of DS-9100HFI-ST Series DVR 12.1.6 Viewing HDD Information Steps: Enter the System Information interface. Menu > Maintenance > System Info Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc., as shown in Figure 12.6.
User Manual of DS-9100HFI-ST Series DVR 12.2 Searching & Export Log Files Purpose: The operation, alarm, exception and information of the DVR can be stored in log files, which can be viewed and exported at any time. Steps: Enter the Log Search interface.
Page 182
User Manual of DS-9100HFI-ST Series DVR Figure 9. And you can also click the button to view the related video files if available. Figure 12.9 Log Details If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 12.10.
User Manual of DS-9100HFI-ST Series DVR 12.3 Importing/Exporting Configuration Files Purpose: The configuration files of the DVR can be exported to local device for backup; and the configuration files of one DVR can be imported to multiple DVR devices if they are to be configured with the same parameters.
User Manual of DS-9100HFI-ST Series DVR 12.4 Upgrading System Purpose: The firmware on your DVR can be upgraded by local backup device or remote FTP server. 12.4.1 Upgrading by Local Backup Device Steps: Connect your DVR with a local backup device where the update firmware file is located.
Page 185
User Manual of DS-9100HFI-ST Series DVR Figure 12.13 FTP Upgrade Interface Enter the FTP Server Address in the text field. Click the Upgrade button to start upgrading. After the upgrading is complete, reboot the DVR to activate the new firmware.
User Manual of DS-9100HFI-ST Series DVR 12.5 Restoring Default Settings Steps: Enter the Default interface. Menu > Maintenance > Default Figure 12.14 Restore Factory Default Click the OK button to restore the default settings. Note: Except the network parameters (including IP address, subnet mask, gateway, MTU, NIC working mode,...
User Manual of DS-9100HFI-ST Series DVR 13.1 Configuring RS-232 Serial Port Purpose: The RS-232 port can be used in two ways: • Parameters Configuration: Connect a PC to the DVR through the PC serial port. Device parameters can be configured by using software such as HyperTerminal. The serial port parameters must be the same as the DVR’s when connecting with the PC serial port.
User Manual of DS-9100HFI-ST Series DVR 13.2 Configuring General Settings Purpose: You can configure the BNC output standard, VGA output resolution, mouse pointer speed through the Menu > Configuration > General interface. Steps: Enter the General Settings interface. Menu > Configuration > General Select the General tab.
User Manual of DS-9100HFI-ST Series DVR 13.3 Configuring More Settings Steps: Enter the General Settings interface. Menu > Configuration > General Click the More Settings tab to enter the More Settings interface, as shown in Figure 13.3. Figure 13.3 More Settings Interface Configure the following settings: •...
User Manual of DS-9100HFI-ST Series DVR 13.4 Managing User Accounts Purpose: There is a default account in the DVR: Administrator. The Administrator user name is admin and the password is 12345. The Administrator has the permission to add and delete user and configure user parameters.
Page 192
User Manual of DS-9100HFI-ST Series DVR Enter the information for new user, including User Name, Password, Level and User’s MAC Address. Level: Set the user level to Operator or Guest. Different user levels have different operating permission. • Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all operating permission in Camera Configuration.
User Manual of DS-9100HFI-ST Series DVR the user. Local Configuration • Local Log Search: Searching and viewing logs and system information of DVR. • Local Parameters Settings: Configuring parameters, restoring factory default parameters and importing/exporting configuration files. • Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property), upgrading system firmware, clearing I/O alarm output.
User Manual of DS-9100HFI-ST Series DVR Figure 13.8 Delete a User Click the icon to delete the selected user. 13.4.3 Editing a User Steps: Enter the User Management interface. Menu > Configuration > User Select the user to be edited from the list, as shown in Figure 13.9.
User Manual of DS-9100HFI-ST Series DVR Figure 13.10 Edit User Interface Edit the user information, including user name, password, level and MAC address. Click the OK button to save the settings and exit the menu. 13.4.4 Changing Password of Admin Purpose: The password of the Admin user account can be changed in the User Management menu.
User Manual of DS-9100HFI-ST Series DVR 13.5 Locking/Shutting down/Rebooting Device Steps: Enter the Shutdown interface. Menu > Shutdown Figure 13.12 Shutdown Menu Click the Lock button to lock the device, or Click the Shutdown button to shut down the device, or Click the Reboot button to reboot the device.
User Manual of DS-9100HFI-ST Series DVR Glossary • Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF.
User Manual of DS-9100HFI-ST Series DVR • Why does my DVR make a beeping sound after booting? The possible reasons for the warning beep on the DVR are as follows: There is no HDD installed in the DVR. The HDD is not initialized.