HIKVISION DS-9100HFI-ST Series Quick Operation Manual
HIKVISION DS-9100HFI-ST Series Quick Operation Manual

HIKVISION DS-9100HFI-ST Series Quick Operation Manual

Ds-9100hfi-st series
Hide thumbs Also See for DS-9100HFI-ST Series:

Advertisement

Quick Links

DS-9100HFI-ST Series DVR
Quick Operation Guide
Version 2.0.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS-9100HFI-ST Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HIKVISION DS-9100HFI-ST Series

  • Page 1 DS-9100HFI-ST Series DVR Quick Operation Guide Version 2.0.2...
  • Page 2: Verify Contents

    Please contact your dealer for damaged or missing items. DVR Pre-Installation The DS-9100HFI-ST Series DVR is highly advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the DVR. 1. Keep all liquids away from the DVR.
  • Page 3 Quick Operation Guide of DS-9100HFI-ST Series DVR 3. Press the buttons on the panel of two sides and open the front panel. 4. Insert the hard disk along the slot until it is placed into position. 5. Repeat the above steps to install other hard disks onto the DVR. After having finished the installation of all hard disks, replace the front panel and lock it with the key again.
  • Page 4: Front Panel

    Quick Operation Guide of DS-9100HFI-ST Series DVR Front Panel Name Function Description ALARM Alarm indicator turns red when a sensor alarm is detected. Ready indicator is normally green, indicating that the DVR is functioning READY properly. Status indicator turns green when DVR is controlled by an IR remote.
  • Page 5 Quick Operation Guide of DS-9100HFI-ST Series DVR Zooming in the PTZ camera in the PTZ Control setting. ZOOM+ Adjusting focus in the PTZ Control menu. It is also used to switch between input methods (upper and lowercase alphabet, symbols and numeric input).
  • Page 6: Rear Panel

    Quick Operation Guide of DS-9100HFI-ST Series DVR Rear Panel Item Description VIDEO IN BNC connector for analog video input. LOOP OUT BNC connector for video loop output. VIDEO SPOT OUT BNC connector for video output. VIDEO OUT BNC connector for video output.
  • Page 7: Peripheral Connections

    Quick Operation Guide of DS-9100HFI-ST Series DVR Peripheral Connections Connecting to Alarm Input / Output Device The alarm input/output interface of the DVR is shown as below: The alarm input is an open/closed relay. If the input is not an open/closed relay, follow the connection diagram...
  • Page 8 Quick Operation Guide of DS-9100HFI-ST Series DVR 1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. 2. Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure signal cables are in tight.
  • Page 9: Specifications

    Quick Operation Guide of DS-9100HFI-ST Series DVR Specifications Model DS-9116HFI-ST DS-9108HFI-ST DS-9104HFI-ST Video compression H.264 8-ch, BNC(1.0Vp-p, 4-ch, BNC(1.0Vp-p, 16-ch, BNC(1.0Vp-p, 75Ω), PAL/NTSC 75Ω), PAL/NTSC Analog video input 75Ω), PAL/NTSC adaptive adaptive adaptive OggVorbis Video/Audio Audio compression input 16-ch, 8-ch,...
  • Page 10 Quick Operation Guide of DS-9100HFI-ST Series DVR SATA 8 SATA interfaces Hard disk eSATA 1 eSATA interface Capacity Up to 4TB capacity for each disk 2, RJ45 10M/100M/1000M adaptive Ethernet Network interface 1 RS-232 interface (for parameters configuration, maintenance, transparent channel);...
  • Page 11: Hdd Storage Calculation Chart

    Quick Operation Guide of DS-9100HFI-ST Series DVR HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K...
  • Page 12: Menu Operation

    Quick Operation Guide of DS-9100HFI-ST Series DVR Menu Operation Menu Structure The menu structure of the DS-9100HFI-ST Series DVR is shown as below: Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the DVR.
  • Page 13: Using The Setup Wizard

    Quick Operation Guide of DS-9100HFI-ST Series DVR Using the Setup Wizard By default, the Setup Wizard will start once the DVR has loaded. Operating the Setup Wizard: 1. The Setup Wizard will walk you through some important settings of your DVR. If you don’t want to use the Setup Wizard at this time, click the Cancel button.
  • Page 14 Quick Operation Guide of DS-9100HFI-ST Series DVR 7. Click Next button after you configure the network parameters to enter the HDD Management window. 8. To initialize the HDD, click the Init button. Initialization will remove all the data saved in the HDD.
  • Page 15: Live View

    Quick Operation Guide of DS-9100HFI-ST Series DVR Live View Some icons are provided on screen in Live View mode to indicate different camera status. These icons include: Live View Icons In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the record and alarm in the channel, so that you can find problems as soon as possible.
  • Page 16: Instant Playback By Channel

    Quick Operation Guide of DS-9100HFI-ST Series DVR PTZ Control In the Live View mode, you can press the PTZ Control button on the front panel or on the remote, or choose the PTZ Control icon to enter the PTZ toolbar.
  • Page 17: All-Day Playback By Channel

    Quick Operation Guide of DS-9100HFI-ST Series DVR All-day Playback by channel 1. Enter the All-day Playback menu. Mouse: right click a channel in live view mode and select All-day Playback from the menu. Front Panel: press PLAY button to play back record files of the channel under single-screen live view.
  • Page 18 Quick Operation Guide of DS-9100HFI-ST Series DVR Backup Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer. To export recorded files: 1. Enter Video Export interface. Choose the channel(s) you want to back up and press Quick Export button.

This manual is also suitable for:

Ds-9116hfi-stDs-9108hfi-stDs-9104hfi-st

Table of Contents