MP3/WMA/SD/USB/AUX CAR RADIO FM Stereo/MW Radio RDS (Radio Data System) Function 4x25 W High Power Output MUTE VOL+ MODE AS/PS 2 INT 3 RPT 4 RDM 5 -10 6 +10 BAND USER MANUAL...
CONTENTS CONTENTS....................................GB-1 ACCESSORIES....................................GB-2 PRECAUTION ....................................GB-3 INSTALLATION ....................................GB-4 USING THE DETACHABLE FRONT PANEL ..........................GB-6 WIRING DIAGRAM ..................................GB-7 LOCATION AND FUNCTION OF KEYS............................GB-8 GENERAL OPERATIONS ................................GB-9 RADIO OPERATIONS................................GB-12 RDS (RADIO DATA SYSTEM) OPERATIONS.......................... GB-14 USB, SD/MMC CARD OPERATIONS ............................GB-15 MP3/WMA FILE OPERATIONS ..............................
ACCESSORIES Mounting Bracket Removable Trim Small metal Strip Plain Washer Spring Washer (Half Sleeve) Ring equipped on the unit Tapping Screw Hex Nut Mounting Bolt Release Key USB Adaptor Cable MUTE VOL+ MODE AS/PS BAND 2 INT 3 RPT 4 RDM 5 -10 6 +10 Protective Case...
PRECAUTION This unit is designed and manufactured with the user’s safety in mind, however any improper use or operation may result in certain dangers. It is therefore highly recommended to read this manual thoroughly and adhere to the following precautions. SAFETY PRECAUTIONS To prevent an electrical shock, do not open the housing of the unit.
INSTALLATION Notes: - Choose the mounting location where the unit will not interfere with the normal driving function of the driver. - Before finally installing the unit, connect the wiring and make sure that the unit works properly. - Consult your dealer if installation requires the drilling of holes or other modifications of the vehicle. - Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
Page 6
6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend out the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. To secure the sleeve in place, bend out the appropriate tabs so that they make contact with the dashboard.
10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel (see the steps of 'TO ATTACH THE FRONT PANEL'). Dismantling the unit 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2.
ISO connector (not supplied): Part A: White RCA connector to rear left White RCA connector to front left A1: No Connect A2: No Connect A3: No Connect A4: Battery B+ (Yellow) A5: Antenna (Blue) A6: No Connect A7: Accessory (12V, To Ignition...
Location and Function of Keys Description of Function Controls (1) Power on/off (MUTE) Button Front panel: (2) LCD display (3) SEL (Select) button (4) Open (REL) Button (5) Volume +/- Button (6) SD/MMC Memory Card Slot (7) USB Port (8) MODE Button (9) CLK (Clock) Button (10) Anti-theft LED indicator (11) RESET Button...
GENERAL OPERATIONS Reset the unit When operating the unit for the first time, after replacing the car battery or changing the connections, you must reset the unit. 1. Turn off the unit power. 2. Press the (REL) button and remove the front panel, then press the RESET button with a ballpoint pen or similar object to restore the unit to the original factory settings.
Page 11
“TA SEEK or TA ALM” “PI SOUND or PI MUTE” “RETUNE L or RETUNE S” “MASK DPI or MASK ALL” “BEEP ON, BEEP OFF" USER SET (FLAT/CLASSIC/ROCK/POP) VOL LAST/VOL DEFA STEREO/MONO (in Radio mode) LOUD OFF/LOUD ON DX/LOCAL (in Radio mode) CLK ON/CLK OFF CLK 12/24 display.
Page 12
Any alternative frequency (AF) with a different PI or which does not broadcast an RDS signal that is strong enough will normally be masked when the PI is checked while the unit searches for an alternative frequency. The unit will not automatically go to this type of alternative frequency.
CLK ON/CLK OFF CLK ON: Time is always displayed at power off mode. CLK OFF: Time is not displayed at power off mode. CLK 12/24 display Select 12 or 24 time display. To select playback mode In power on mode, press MODE button repeatedly to select the different modes in the following sequence: TUNER, USB (with USB device inserted), CARD (with SD/MMC card inserted), AUX in mode.
Page 14
Press and hold the button to launch the automatic search forwards or backwards.The radio will search up or down for a strong signal radio station within the current band.. - Manual search mode: Press the button repeatedly to manually search upward or downward step by step for the desired radio station within the current band.
RDS (RADIO DATA SYSTEM) OPERATIONS The RDS data are the PI, PS, TP, PTY, TA and AF data. PI (Program identification): Code for identifying the radio station. PS (Program service): Name of the radio station. PTY (Program type): Type of program such as news, Pop music, sports etc. TP (Traffic program): Code indicating a station broadcasting traffic information.
FOLK M When you select the SPEECH PTY GROUP, the preset numbered buttons is shared as follows: Preset number Speech PTY Group NEWS, AFFAIRS, INFO SPORT, EDUCATE, DRAMA CULTURE, SCIENCE, VARIED WEATHER, FINANCE, CHILDREN SOCIAL, RELIGION, PHONE IN TRAVEL, LEISURE, DOCUMENT When you select a program type, the tuner will search for a station broadcasting this type of program.
- Use the USB adaptor cable, if necessary. - When reading the USB stick or card, please don't touch or remove it. - If following the instruction above, the unit can't read the file in the USB stick or card, please check if the device is in good condition, or take it out then insert it into the USB port or card slot once more.
Page 18
In MP3/WMA files playback, briefly press the RPT button to continuously play the current track. “RPT ONE” is displayed. Press it again to play all of the tracks in the current folder repeatedly. “RPT ABM” is displayed. Press again to stop repeat playback and resume normal playback.
AUX IN OPERATIONS This system has an external input jack, so you can listen to music from external devices connected to this unit. Press the MODE button to switch to the AUX mode. SPECIFICATIONS 1. GENERAL Power Supply Requirements ..................DC 12 Volts, Negative Ground Unit Dimensions ......................
TROUBLESHOOTING Symptom Cause Solution No power The car ignition switch is not on. Turn the ignition key to “ACCESSORY” in order to switch the unit on. The connections are not correct. Check the connections. A fuse has blown in the vehicle. Check the vehicle fuses.