Subscribe to Our Youtube Channel
Related Manuals for Evolution Rage3B2102
Summary of Contents for Evolution Rage3B2102
- Page 1 ® 210mm (8-1/4”) TCT Multipurpose Compound Mitre Saw Original Instruction Manual Read instructions before operating this tool Rage3B2102 / Rage3B2102eU / Rage3B2101 VERS 1 REV 0 - 03.12...
- Page 2 ® SPECIFICATIONS Designed to cut: Mild Steel Plate – Max Thickness (mm) Mild Steel Box Section – Max Wall Thickness (mm) Wood – Max section (mm) 50 x 120 Motor (230V ~ or 110V ~ 50/60 Hz) (Watts) 1100w (230v) 1600w (110v) RPM No Load (min-1) 4000 Recommended Maximum Duty Cycle (Minutes)
-
Page 3: Table Of Contents
TABLE OF CONTENTS PAGE Introduction guarantee Vibration explanation of Labels and Symbols Instruction Manual Intended use of this Power Tool 5 - 6 Read instructions before operating this tool. Prohibited use of this Power Tool SAFETY PRECAUTIONS electrical Safety general Power Tool Safety Instructions 6 - 7 Specific Safety Instructions Personal Protective equipment (PPe) -
Page 4: Introduction
INTRODUCTION Claims made under this guarantee must be made directly to Evolution Power Tools within Congratulations on your purchase of an the guarantee period. all defective goods shall be returned / collected at Evolution Power Evolution Power Tools machine. This product has been manufactured to the Tools cost. -
Page 5: Vibration
Contact evolution Power Tools for arm. It is possible that the operator could replacement labels. develop “Vibration white finger disease”... -
Page 6: Prohibited Use Of This Power Tool
THIS PRODUCT IS DOUBLE INSULATED AND THEREFORE DOES NOT REQUIRE A When fitted with a correct blade this CONNECTION TO EARTH. machine can be used to cut: Wood, Wood derived products (MDF, Chipboard, Plywood, Blockboard, Hardboard • THE 3 PIN PLUG MUST COMPLY TO BS1363/A. - Page 7 • Do not expose power tools to rain or earth exceeds 30ma for 30ms. always check wet conditions. Water entering a the operation of the residual current device power tool will increase the risk of (R.C.D.) before using the machine. If an extension cable is required it must be a electric shock.
-
Page 8: Specific Safety Instructions
• Do not overreach. Keep proper footing sharp cutting edges are less likely to bind and balance at all times. This enables and are easier to control. better control of the power tool in unexpected situations. • Use the power tool, accessories and •... -
Page 9: Personal Protective Equipment (Ppe)
Never attempt to retrieve sawn material until the the slide bars are locked). Lift the machine by cutting head is in the raised position, the guard is gripping the outer edges of the base with both fully closed and the saw blade has stopped rotating. hands (if a sliding mitre saw, transport using Only use saw blades that are recommended by the handles provided). -
Page 10: Getting Started - Unpacking
WARNING: the operation of any mitre saw • Loosen the Mitre angle Locking Screw. can result in foreign objects being thrown Turn the table to either of its maximum towards your eyes, which could result in severe settings. eye damage. Before beginning power tool •... - Page 11 (or evolution Power Tools). UNLATCHING AND RAISING THE CUTTING HEAD WARNING: To avoid serious injury, NEVER...
-
Page 12: Machine Overview
210 COMPOUND MITRE SAW ReVeRSe OF MaCHINe (15) (16) (17) (18) (12) (10) (19) (11) (13) (14) 1. ON/OFF TRIGGER SWITCH 11. MITRE LOCKING SCREW 2. BLADE GUARD LOCKING LEVER 12. MITRE ANGLE SCALE 3. CUTTING HANDLE 13. FENCE 4. DUST BAG (Optional Accessory) 14. -
Page 13: Assembly And Preparation
ASSEMBLY and PREPARATION WARNING: Always disconnect the saw from the power source before making any adjustments. PERMANENTLY MOUNTING THE MITRE SAW To reduce the risk of injury from unexpected saw movement, place the saw in the desired location either on a workbench or other suitable machine stand. The base of the saw has four mounting holes through which suitable bolts (not supplied) can be placed to secure the miter saw. - Page 14 FOR PORTABLE USE: • Mount the saw on a 18mm thick piece of plywood or MDF (800mm x 500mm min size recommended) using appropriate fastenings (not supplied). • It may be necessary to countersink the washers, nuts, etc. to the underside of the plywood or MDF mounting board to avoid an uneven work surface.
-
Page 15: Operating Instructions
OPERATING INSTRUCTIONS CAUTION: The Mitre Saw should be inspected (particularly for the correct functioning of the safety guards) before each use. Do not connect the saw to the power supply until a safety inspection has been carried out. ensure that the operator is adequately trained in the use, adjustment and maintenance of the machine, before connecting to the power supply and operating the saw. - Page 16 BEVEL ANGLES (0 AND 45 Bevel Stop Adjustment • ensure that the Cutting Head is in the locked down position with the latching pin fully engaged in its socket. (see Fig.6) • ensure that the Cutting Head is upright, against its stop and the bevel pointer is indicating 0 on the scale.
- Page 17 Bevel Stop Adjustment • Loosen the Bevel Lock Handle and tilt the Cutting Head completely to the left until it rests against the 45 stop. • Use a Set Square to see if the blade is at 45 the table (avoiding the TCT tips). •...
- Page 18 Fence Alignment The fence must be aligned at 90 (square) to a correctly installed blade The rotary table must be set at ‘0 ’ miter angle. The Fence is fastened to the table with two socket head Hex screws positioned one at either side of the fence in elongated slots.
- Page 19 • ensure that the ‘cut-off’ material is free to move sideways away from the blade when the cut is completed. ensure that the ‘cut-off’ piece cannot become ‘jammed’ in any other part of the machine. • Do not use this saw to cut small pieces. If the workpiece being cut would cause your hand or fingers to be within 150mm of the sawblade, the workpiece is too small.
- Page 20 MITRE CUTTING (Fig. 17) The rotary table of this machine can be turned through to the left or right from the normal cross-cut (0 position. Positive stops are provided at 45 , 40 , 35 , 22.5 , 15 , 10 and 5 to both the right hand and left hand sides.
- Page 21 To tilt the Cutting Head to the left: • Loosen the bevel locking screw. (Fig. 20a) • Tilt the Cutting Head to the required angle. a protractor scale is provided as an aid to setting. (Fig 20b) • Tighten the bevel locking screw when the desired angle has been selected.
- Page 22 Fig. 24 WARNING: Only carry out this operation with the machine disconnected from the mains supply. WARNING: Only use genuine evolution blades which are designed for this machine. ensure that the maximum speed of the blade is higher than the speed of the motor.
- Page 23 • ensure the blade guard is fully functional before using the machine. USE OF OPTIONAL EVOLUTION ACCESSORIES (not supplied as original equipment – see additional accessories pp 11) DUST BAG a Dust Bag can be fitted to the extraction port at the rear of the machine.
-
Page 24: Maintenance
Replacement inserts are available handling. Please contact your local authority from evolution Power Tools. for further details of your nearest designated collection point. Penalties may be applicable for To replace the table inserts: incorrect disposal of this waste in accordance with national legislation. - Page 25 NOTES www.evolutionpowertools.com...
-
Page 26: Service Parts Diagram
SERVICE PARTS DIAGRAM www.evolutionpowertools.com... -
Page 27: Declaration Of Conformity
® The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial estate, Sheffield, S20 3FR The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below. - Page 28 ® UK HQ FRANCE HQ USA HQ Evolution Power Tools, Evolution Power Tools, Evolution Power Tools LLC, Venture One, Longacre Close, 61 avenue Lafontaine, 33560, 8363 Research Drive, Holbrook Industrial estate, Carbon-Blanc, Davenport,Iowa 52806 Sheffield, S20 3FR, UK France U.S.a TeL: +44 (0) 114 251 1022 TÉL: + 33 (0)5 57 30 61 89...
Need help?
Do you have a question about the Rage3B2102 and is the answer not in the manual?
Questions and answers