Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Evolution Rage
Summary of Contents for Evolution Rage
- Page 1 Original Instructions Written in UK English Date Published: 18 / 09 / 2013...
- Page 3 ENGLISH Original Instructions...
-
Page 4: Table Of Contents
www.evolutionpowertools.com TABLE OF CONTENTS English Page 2 Italiano Pagina 22 INTrOduCTION Guarantee Page 5 Machine Specification Page 6 Vibration Page 7 Labels and Symbols Page 7 Intended use of this Power Tool Page 8 Prohibited use of this Power Tool Page 8 SAFETY PrECAuTIONS Electrical Safety... -
Page 5: Guarantee
In no event shall you to validate your machine’s guarantee period via Evolutions website by entering your Evolution Power Tools be liable for loss or details and thus ensure prompt service if ever damage resulting directly or indirectly from the use of our merchandise or from any other needed. -
Page 6: Machine Specification
www.evolutionpowertools.com SPECIFICATIONS MAChINE METrIC IMPErIAL Motor (USA) 120v ~ 60Hz 1050W Motor (UK/EU) 230/240v ~ 50Hz 1050W Motor (UK) 110v ~ 50Hz 1050W Speed No Load 3500min 3500rpm Weight 6.5kg 14lbs CuTTING CAPACITY METrIC IMPErIAL Mild Steel Plate (Maximum Thickness) 1/4”... -
Page 7: Vibration
Do not operate this machine • The measurement and assessment of if warning and/or instruction labels are human exposure to hand-transmitted missing or damaged. Contact Evolution vibration in the workplace is given in: Power Tools for replacement labels. BS EN ISO 5349-1:2001 and Note: All or some of the following symbols BS EN ISO 5349-2:2002. -
Page 8: Intended Use Of This Power Tool
This product is a Hand Operated Circular Saw and has been designed to be Volts used with special Evolution blades. Only use accessories designed for use in this machine and/or those recommended specifically Amperes by Evolution Power Tools Ltd. -
Page 9: Electrical Safety
www.evolutionpowertools.com (1.14) ELECTrICAL SAFETY (2.2) 1) General Power Tool Safety warnings [work area safety] This machine is fitted with the correct a) Keep work area clean and well lit. moulded plug and mains lead for the designated market. If the supply cord is Cluttered or dark areas invite accidents. - Page 10 www.evolutionpowertools.com (2.4) 3) General Power Tool Safety (2.5) 4) General Power Tool Safety warnings [Personal Safety]. warnings [Power tool use and care]. a) Do not force the power tool. Use the a) Stay alert, watch what you are doing and use common sense when operating a power correct power tool for your application.
-
Page 11: Additional Safety Instructions
www.evolutionpowertools.com (2.6) 5) General Power Tool (2.8) wArNING: the operation of any power Safety warnings [Service] tool can result in foreign objects being thrown towards your eyes, which could result in a) Have your power tool serviced by a severe eye damage. Before beginning power qualified repair person using only identical tool operation, always wear safety goggles replacement parts. - Page 12 www.evolutionpowertools.com i) Do not use High Speed Steel (HSS) b) If the blades are binding, or when saw blades. interrupting a cut for any reason, release j) Inspect the machine and the blade the trigger and hold the saw motionless before each use.
-
Page 13: Getting Started Unpacking
Be aware of the time it takes for the with this machine the following accessories blade to stop after switch is released. are also available from the Evolution online shop at www.evolutionpowertools.com (3.4) wArNING: If any parts are missing, do or from your local retailer. -
Page 14: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW 1. ON/OFF TrIGGEr SwITCh 2. AuXILLArY FrONT hANdLE 3. dISChArGE POrT 4. LOwEr BLAdE GuArd 5. FITTEd BLAdE IN SITu... -
Page 15: Assembly And Preparation
Country of use. Do not alter or modify the power cord. Fig. 1 Installing or removing a Blade wArNING: Only use genuine Evolution blades which are designed for this machine. Ensure that the maximum speed of the blade is compatible with the machine. Only perform this operation with the machine disconnected from the power supply. - Page 16 www.evolutionpowertools.com 10. Replace the chip collector and securely tighten the two thumb screws. 11. Check that the arbor lock is fully released by manually rotating the blade. 12. Check the operation of the safety guard. Parallel Edge Guide A parallel guide (for help when rip cutting) can be fitted to the sole plate of the machine The guides arms should be inserted Fig.
-
Page 17: Operating Instructions
www.evolutionpowertools.com Operating Advice Carry out routine safety checks each time you use the machine. Check that all safety guards are operating correctly, and that all adjustment handles/screws are tightened securely. Check that the blade is secure and installed correctly. Also check that it is the correct blade for the material being cut. - Page 18 www.evolutionpowertools.com discharge Port When cutting wood the Discharge Port Exhaust should be fitted to the chip collector cover Discharge Port. To fit the discharge Port Exhaust • Remove the Discharge Port blanking cover by unscrewing the cross headed screw. • Pull the blanking cover from the Discharge Port and safely Fig.
-
Page 19: Maintenance
www.evolutionpowertools.com wArNING: Do not attempt to clean by When a cut has been completed release the ON/OFF trigger switch and allow the blade to inserting pointed objects through openings come to a complete halt. Do not apply lateral in the machines casings etc. The machines air pressure to the blade disc in an attempt to vents should be cleaned using compressed slow it down more quickly. -
Page 20: Declaration Of Conformity
In accordance with EN ISO 17050-1:2004 The manufacturer of the product covered by this declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below. - Page 21 www.evolutionpowertools.com NOTES...
- Page 22 Evolution Power Tools Ltd Evolution Power Tools LLC Venture One 8363 Research Drive Longacre Close Davenport Holbrook Industrial Estate Iowa Sheffield 52806 S20 3FR +44 (0)114 251 1022 866-EVO-TOOL エボリューション Evolution Power Tools Ltd パワーツール株式会社 61 Avenue Lafontaine 〒544-0031 33560 大阪府大阪市生野区...
Need help?
Do you have a question about the Rage and is the answer not in the manual?
Questions and answers