FEATURES Surface-mounted, 7 inch color TFT screen with sensor buttons Intercom, broadcast, call transfer among indoor monitors Supports up to 4 indoor monitors and 2 doorbell cameras Supports image capture function with 64 images memory Supports removable SD card for saving captured images to computer for history record Room-to-room internal communication Supports 4 CCTV cameras for security surveillance Can view 1 of 6 different video images from each indoor monitor at the same time...
MONITOR DESCRIPTION - REAR 14----------Terminal for Door Bell 1 15----------Terminal for Door Bell 2 16----------Terminal for Extension Video/ Audio Line in 17----------Terminal for Main Monitor (ROOM1) 18----------Terminal for Sub Monitor 2/3/4 (ROOM2, ROOM3, ROOM4) 19----------Power Input 19VDC 20----------Power ON/OFF...
MONITOR INSTALLATION GUIDE Indoor Monitor Installation Select the relevant wiring diagram from pages 8 and 9 that matches your installation requirement Ensure you have the correct cable according to the system’s requirements Select correct height for the indoor monitor (generally 145-160cm) - See Figure 1 below Next determine the position for the monitor bracket, run cable through bracket and fix locating screws in bracket...
DOORBELL INSTALLATION GUIDE Doorbell/Camera Installation Select the most suitable position for Doorbell/Camera. Consider factors such as day time operation, night time operation and impact of likely weather conditions. Direct sunlight on the camera and direct contact with rain should be avoided. Determine Camera Position: Recommended height of the camera is approximately 145 to 160 cm...
MAIN MENU DESCRIPTION In standby mode, press and hold the “MENU/SET” button for 2 seconds, to enter the main menu set-up interface as follows: Press “MENU/SET” button to move cursor to the next sub item setup menu option. Press “NEXT” button to enter the sub menu interface. - Use “PREV”...
CHIME SET - chime duration and chime type The chime duration is adjustable from 10 to 30 seconds, The Chime Type provides a choice of 10 different chimes for Door1, Door2, and intercom calls Programming Procedure: After entering the main menu interface, press the “ ”...
VOLUME SET - Chime, Talk and CCTV Chime, Talk and CCTV volume can be set to High, Low or Mute. Adjustment Procedure: In the main menu, press the “Menu/Set” button to move the cursor to the “VOLUME SET” option, Press the “NEXT” button to enter the VOLUME SETTING sub menu interface as follows: Use the “PREV”...
Page 20
Use “Menu/Set button to select Photo Module option Press “Next” button to Enable or Disable ENABLE – Images will be recorded DISABLE – Images will not be recorded Use “Menu/Set button to select Photo Set option Press “Next” button to Enter Photo Set sub menu as follows: Note: Any one of the following windows may appear Use “Menu/Set”...
OTHER SET: Unlock Time, Door 1, Door 2, CCTV Num UNLOCK TIME, for Door Unlock function, can be preset from 1 to 9 seconds. Door 1 and Door 2 can be individually ENABLED or DISABLED If you only install one doorbell, you will only need to activate Door 1. If you install 2 doorbells, you should enable both door 1 and door 2.
How to answer the door bell and release the door lock? When a visitor presses the doorbell button, all indoor monitors will chime. The screen will display an image from the door camera, a description “DOOR 1” or “DOOR 2” and a message “PLEASE TAKE UP”. At this time you can see the visitor, know if the call is from door 1 or door 2 and answer the call.
How to monitor Video and Audio Inputs? There are six Audio/Video channels that can be viewed individually at any of the indoor monitor units at any time. The first two channels are Door-1 and Door-2 and provide both video and audio signals from each of the doorbell units.
How to communicate? There are two ways to communicate between monitors: 1. Call all monitor stations Press the “Answer Intercom” button at a monitor station - The chime will activate at all monitor stations - “All” and “Intercom Request” will be displayed at the calling station - The Room Number of the calling station and “Please Take Up”...
Image Capture function 1. Auto Capture: If the door chime is activated by a visitor but no one replies from any of the monitor units, the system will take an image of the visitor and store it for later viewing. Up to 64 images, with date/time stamp, can be stored. When image storage is full, the oldest image is deleted each time a new image is added.
LED Operation LED STATUS Red Light On Standby Mode Green Light On Communication Mode Blue Light On Captured Images Not Yet Viewed Red Light Flashing Standby in Do Not Disturb Mode Green Led Flashing Communication in Do Not Disturb Mode Blue Led Flashing Captured Images Not Yet Viewed In DND Mode DOCUMENT No: 890-404...
Page 28
IntercOm Owners manual rev 1, november 2009 document part number: 890-0 cOpyrIGHt nOtIce all rights reserved. no part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of ness.