Ozito 18V Li-ion Instruction Manual
Ozito 18V Li-ion Instruction Manual

Ozito 18V Li-ion Instruction Manual

Cordless pole pruner & hedge trimmer

Advertisement

CORDLESS
POLE PRUNER & HEDGE
TRIMMER
18V Li-ion
INSTRUCTION MANUAL

SPECIFICATIONS

Input:
18V
Battery:
1.5Ah Li-Ion
Charge Time:
90 Minutes
Pole Pruner -
Bar Length:
200mm (8")
Chain Pitch:
9.53mm (3/8")
Chain Gauge:
1.3mm (0.050")
Hedge Trimmer -
Blade Length:
400mm
Cutting Capacity:
15mm
Pivoting Head:
10 position
ozito.com.au
2
WHAT'S IN THE BOX
Power Handle
Hedge Trimmer
Attachment
Pruner Attachment
18 Volt Battery & Charger
Shoulder Strap, Hex Key/
Screwdriver, Blade Cover &
Chain Cover
PHT2-018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 18V Li-ion and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ozito 18V Li-ion

  • Page 1: Specifications

    WHAT’S IN THE BOX CORDLESS Power Handle POLE PRUNER & HEDGE TRIMMER Hedge Trimmer 18V Li-ion Attachment INSTRUCTION MANUAL SPECIFICATIONS Pruner Attachment Input: Battery: 1.5Ah Li-Ion Charge Time: 90 Minutes Pole Pruner - Bar Length: 200mm (8”) Chain Pitch: 9.53mm (3/8”) Chain Gauge: 1.3mm (0.050”)
  • Page 2: Know Your Product

    KNOW YOUR PRODUCT SETUP & PREPARATION SETUP & PREPARATION POWER HANDLE 1. ASSEMBLY 1 Collar 6 Wire Loop 2 Shaft 7 Lock Off Switch 1. Fit the mounting bracket 2. Position the mounting 3 Secondary Handle 8 Battery onto the power handle bracket 4 Mounting Bracket 9 On/Off Trigger Switch...
  • Page 3: Battery And Charger

    2. BATTERY & CHARGER 3. POLE PRUNER PREPARATION Chain bar oil This charger is recommended for use with a residual current device with a rated residual current of 30mA or less. WARNING!: Pole pruner comes from the factory with no chain bar oil added. Oil level should also be Charging checked after every 15 minutes of use and refilled 2.
  • Page 4: Operation

    OPERATION 4. ON/OFF SWITCH 5. POLE PRUNER For your safety the power handle is designed with a safety lock WARNING!: Never start work unless the chain and bar are off mechanism. This prevents accidental starting. lubricated. If the pruner is used without oil, the chain and bar may become very hot and may wear out very quickly due to the strong friction, potentially causing kick back of 1.
  • Page 5: Working Position

    6. POLE HEDGE TRIMMER Be aware of the direction in which the LOAD WARNING!: Never use the pole hedge trimmer when branch will fall. Cut lower branches first standing on a ladder or uneven ground. If the blades to allow the top branches more room to comes in contact with a hard object, visually inspect the fall.
  • Page 6: Maintenance

    For further information, or any parts not listed here, visit Maintaining the guide bar www.ozito.com.au or contact Ozito customer service 1. Remove any sawdust from the groove in Australia 1800 069 486 the guide bar, including the groove.
  • Page 7 SPARE PARTS Model No. PHT2-018 Pole Pruner 10 11 12 13 14 5 6 7 8 9 The following is a list of spare parts carried by Ozito. Please contact Customer Service for any parts not listed. Item Item Description Part No.
  • Page 8: Hedge Trimmer

    Tool: Cordless Pole Pruner & Hedge Trimmer SPARE PARTS Model No. PHT2-018 Hedge Trimmer 36 37 The following is a list of spare parts carried by Ozito. Please contact Customer Service for any parts not listed. Item Item Description Part No.
  • Page 9: General Power Tool Safety Warnings

    GENERAL POWER TOOL SAFETY WARNINGS d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result WARNING! Read all safety warnings and all instructions. Failure to follow in personal injury.
  • Page 10: Hedge Trimmer Safety Warnings

    HEDGE TRIMMER SAFETY WARNINGS • Keep all parts of the body away from the cutter blade. Do not remove cut • Switch on the Pole Hedge Trimmer only when hands and feet are away from the material or old material to be cut when blades are moving. Make sure the switch cutting blades.
  • Page 11: Warranty

    • Failure to perform maintenance as set out within the instruction manual. • If the tool is disassembled or tampered with in any way. • Professional, industrial or high frequency use. OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175. 0213...

This manual is also suitable for:

Pht2-018

Table of Contents