Table of Contents
Advertisement
i
nstallatiOn
Adjusting the quick release skewer
Operate.the.quick.release.lever.–.open/close.
)
.
If.the.quick.release.lever.can.be.closed.too.easily,.the.quick.release.
L
L
[
screw.
(
1
)
.must.be.adjusted.
g1
Move.the.quick.release.lever.up.(CLOSED).
)
.
Screw.in.the.quick.release.screw.by.¼.turn.clockwise.
)
.
Operate.the.quick.release.lever.–.open/close.
)
.
Repeat.the.procedure.if.necessary.
)
.
Installing the brake booster
Unscrew.the.right.adapter.screw.
)
.
Push.the.brake.booster.onto.the.left.adapter.screw.
)
.
Secure.the.brake.booster.with.the.adapter.screw.
)
.
Tighten.the.right.adapter.screw..
)
.
[
]
max. 6 Nm (53 lbf·in).
.
C1
Shortening brake hose
Important.– see.
,.page.16!
general
Push.the.double.hose.cover.
(
1
)
.
Cut.off.the.brake.hose.approx..12.mm.before.the.end.of.the.hose.–.use.
)
.
a.MAGURA.hose.cutter.if.required.
Twist.the.barbed.fitting.
.out.of.the.brake.cylinder.with.the.remains.of.
(
2
)
)
.
the.hose.
The.cut-off.barbed.fitting.cannot.be.reused!
Î
Î
Hold.the.end.of.the.brake.hose.to.the.brake.cylinder
)
.
Unusable brake hose – because it is too short.
Calculate.the.insertion.depth.(~5.mm).of.the.brake.hose.in.the.brake.
Î –
[
]
cylinder
.
D3
Mark.the.cut.on.the.brake.hose.
)
.
Place.the.brake.hose.on.a.solid.surface.(wood,.plastic,.etc.).and.cut.at.
)
.
right.angles.with.a.sharp.blade.–.if.required.use.the.MAGURA.hose.
cutter.
18
]
:
.(as.seen.from.above).
(
4
)
(
4
)
.and.washer.
.with.a.tightening.torque.of.
(
4
)
[
]
.upwards.
.
)
D1
[
]
D3
.
Place.the.sleeve.nut.
.and.olive.
(
4
)
)
.
Insert.the.brake.hose.into.the.brake.cylinder.to.the.stop.and.hold.in.
)
.
position.
Screw.the.sleeve.nut.
(
)
.into.the.brake.cylinder.and.tighten.to.a.tighten-
1
)
.
ing.torque.of.4 N·m (35 lbf·in)
Remove.any.oil.residues.thoroughly.
)
.
Pull.and.hold.brake.lever.
)
.
Make.sure.that.all.connections.are.tight.
)
.
Push.the.hose.cover.
(
1
)
.downwards.
)
.
Adjusting the brake levers
You.can.adjust.the.position.(grip.width).of.the.brake.levers.of.your.
L
L
MAGURA.HS.according.to.your.requirements.
This.adjustment.does.not.have.any.effect.on.the.pressure.point.of.the.
brake!
Screw.the.adjusting.screw.
(
1
)
.
Brake.lever.moves.closer.to.the.handlebar.
Î
Î
Screw.the.adjusting.screw.in.
)
.
Brake.lever.moves.further.away.from.the.handlebar.
Î
Î
All.installation.work.is.complete.–.the.brake.is.ready.for.use.
Î
Î
[
]
.on.the.brake.hose
.
(
5
)
D4
[
]
.
B1
[
]
E1
.
)
.out.
-
.
(
)
+
.
(
)
Hide quick links:
Advertisement
Table of Contents
