Page 1
Garden Cultivator ® FGH 700/10 G arden Cultivator O peration and Safety Notes...
Page 2
reading, unfold the page containing the illustrations and familiarise yourself with all functions of the GB / IE / CY Operation and Safety Notes Page...
User manual Safety notes This section deals with the basic safety regu- FGH 700/10 Electric Tiller lations while working with the electric tiller. Contents Symbols Safety notes ..........4 Symbols on the tool Symbols ............ 4 General safety notes ......... 5...
footwear with non-slip soles and strong Symbols in the manual long trousers. Do not use the tool barefoot or wearing open-toed sandals. Warning symbols with information • To prevent injury from the tines, only on damage and injury prevention. switch the tool on in its working position. Instruction symbols (the instruction is •...
Page 6
If working on a slope, work along the the mains under the following circum- slope, not upwards or downwards. Be stances: particularly careful when changing direc- - Always before leaving the tool. tion on the slope. Do not use the tool on - Before removing remnants of soil and excessively steep slopes. plants •...
Functional parts plugging it from the mains. • Make sure that the mains voltage match- es the data on the tool’s rating label. 1a Right-hand fork grip with dead-man • If possible, connect the tool to a socket lever, safety release catch and cable with a residual-current (RC) trip switch at a tension relief triggering current of not more than 30 mA. 1b Left-hand fork grip •...
Assembly instructions Operation Always disconnect the tool from the Observe noise-abatement laws and lo- mains before conducting any work on it. cal by-laws. Scope of delivery Switching on and off Carefully remove the tool from the packaging Note: Before switching the tool on, and check that the following parts are com- make sure that the tool is not touch- plete:...
Wear protective gloves when carrying To avoid damage to the tool: • Never lift or drag the tool with the mo- out maintenance and cleaning work on tor running. the tool to avoid injury from cuts. • Lift the tool while moving it over hard surfaces such as tiles or steps. Always clean the tool thoroughly after each use.
Guarantee 3. Clean the driveshaft with biological oil. • This tool is subject to a guarantee period 4. Slide the new tines onto of thirty-six months. A shorter guarantee the driveshaft with the period of 12 months shall apply for com- holes on the axles mercially used and replacement tools ac- aligned to the holes on cording to statutory regulations.
Replacement parts Technical specifications Use the service address or fax number sup- FGH 700/10 Electric Tiller plied to order replacement parts. Make sure Motor power input .........710 W you include the order number in your order. Mains voltage ........230V AC Mains frequency ........50 Hz Set of tines Working width ........360 mm Right/left ......
EU declaration of conformity We hereby confirm that the FGH 700/10 series electric tiller conforms with the following applicable relevant version of the EU guidelines as of model year 2008: 2006/42/EC • 2004/108/EC • 2000/14/EC In order to guarantee consistency, the following harmonised standards as well as national standards and stipulations have been applied: EN 709+A2:2009 • EN 60335-1/A13:2008 • EN 62233:2008 EN 55014-1:2006 • EN 55014-2/A2:2008 • EN 61000-3-2:2006 • EN 61000-3-3:2008...
Grizzly Service-Center DES UK Ltd. Unit B7 Oxford Street Industrial Park Vulcan Road Bilston, West Midlands WV14 7LF Tel: 0870 7876177 Tel from Ireland: 0044 870 787 6177 Fax: 0870 7876168 Fax from Ireland: 0044 870 787 6168 Email: grizzly@deslimited.com 2009-10-26-rev02-op...
Page 16
I AN 38027 G rizzly Gartengeräte GmbH & Co. KG A m Gewerbepark 2 D -64823 Groß-Umstadt Last Information Update: 10 / 2009 Ident.-No.: 76005526102009-6...