Table of Contents
Advertisement
Responder HD Models
Viper 5904
Clifford 590.4X
Python 594
Security and Remote Start
Installation Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a per-
son other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2011 Directed Electronics, Vista, CA
N5904 2011-09b
Advertisement
Table of Contents
Related Manuals for Directed Electronics Viper 5904
Summary of Contents for Directed Electronics Viper 5904
- Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a per- son other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2011 Directed Electronics, Vista, CA N5904 2011-09b...
- Page 2 Safe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nui- sance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics. The Bitwriter (p/n 998U) ® requires chip version 2.7 or newer to program this unit.
-
Page 3: Table Of Contents
Contents Warning! safety first ........................4 Wiring Diagram ..........................5 Wiring Connections ........................6 Main Harness (H1), 6-pin connector ................... 6 H2 Harness, 24-pin connector ....................6 Remote Start, (H3) 10-pin connector ................... 7 Door Lock, 3-pin connector ......................7 Adjusting the Sensor ........................ -
Page 4: Warning! Safety First
This testing should be performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. -
Page 5: Wiring Diagram
D2D Port (for external Harness Port Xpresskit interface module) Aux/Shutdown/Trigger 24-pin Harness Note: Sensor ports 1 and 2 cannot support sensor 508D due to current limitations. These ports are also constant power and ground connections. © 2011 Directed Electronics. All rights reserved. -
Page 6: Wiring Connections
*The Normally Closed setting will only work if one of the vehicle's doors is connected. If more than one door is to be monitored, then it is recommended to use the Xpresskit DTIMAZDA or tech tip # 1921 on www.di- rectechs.com to interface with these types of vehicles. © 2011 Directed Electronics. All rights reserved. -
Page 7: Remote Start, (H3) 10-Pin Connector
To reset Virtual Tach, go into the Reset and Deletion section of this guide. Virtual Tach cannot be reset with the Bitwriter. Note: Virtual Tach cannot be used in MTS Manual Transmission Mode. It is also not recommended for diesel trucks. © 2011 Directed Electronics. All rights reserved. -
Page 8: Learning The Tach (Not Needed With Virtual Tach)
If the vehicle is not a General Motors product or a Dodge Dakota pickup, please call Directed Electronics Technical Support for an alternative shut-down method. Do not return the vehicle to the customer until this feature is properly installed! -
Page 9: Remote Start Shutdown/Startup Diagnostics
Brake wire is active 6 flashes Hood pin wire is active 7 flashes Manual transmission mode is enabled and not initialized. 8 flashes Neutral safety wire has no ground or the neutral safety switch is Off. © 2011 Directed Electronics. All rights reserved. -
Page 10: Remote Pairing
5. The vehicle siren will chirp. You have now successfully learned the remote to the vehicle remote start and security system. 6. Press the button two times to exit learn routine on the remote. The transmit LED will turn off and exit tone will sound. © 2011 Directed Electronics. All rights reserved. -
Page 11: Programming System Features
The learn routine exits if any of the following occurs: • The open door is closed • The ignition is turned On • There is no activity for 30 seconds • The Control button is pressed too many times © 2011 Directed Electronics. All rights reserved. -
Page 12: Feature Menus
2. On w/Warn Chirps Off: arm and disarm chirps are active, warn-away chirps are defeated 3. Off w/Warn Chirps On: arm and disarm chirps are defeated, warn-away chirps are active 4. Off w/Warn Chirps Off: arm, disarm, and sensor warn-away chirps are defeated © 2011 Directed Electronics. All rights reserved. - Page 13 15. Remote Button Unlock (Ign off) 1. On: a message telling the 2-way remote control to unlock the keypad is sent each time the vehicle ignition is turned off 2. Off: no message is sent © 2011 Directed Electronics. All rights reserved.
-
Page 14: Menu 2 - Convenience
5. Ign-controlled Dome light 1. On: the dome light output will activate when the ignition is turned off 2. Off: the dome light output will not activate when the ignition is turned off © 2011 Directed Electronics. All rights reserved. - Page 15 15. Aux 4 Output Type • Refer to Aux 1 Output Type descriptions 16. Aux 4 Linking • Refer to Aux 1 Linking descriptions 17. Aux/Trunk Output Type • Refer to Aux 1 Output Type descriptions © 2011 Directed Electronics. All rights reserved.
-
Page 16: Menu 3 - Remote Start
Menu 3 - Remote start Menu Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+ Item Transmission Mode Automatic Manual Engine Checking Mode Virtual Tach Voltage Tachometer Cranking Time 0.6 sec. 0.8 sec. 1.0 sec. 1.2 sec. 1.4 (5)/ 1.6 (6)/ 1.8 (7) 2.0 (8)/ 4.0 Remote Start Runtime... - Page 17 2. On: the report is sent every 2 minutes during remote start if the temperature has changed (+/-) 1 degree since the last report 16. Remote start Safelock 1. Off: the Door lock and Factory Alarm Re-arm outputs will maintain the current status (locked/un- © 2011 Directed Electronics. All rights reserved.
-
Page 18: Bitwriter - Only Options
Unlocked Locked Transmitter Programming Locked Unlocked Remote Start Runtime 12 min. Options: 1 to 60 min. Virtual Tach Fine tune Not Initial- Options: Not initialized, 0 to 1000 in 50 millisecond increments ized © 2011 Directed Electronics. All rights reserved. - Page 19 22. Remote Start Runtime: sets the duration of runtime when the engine is started by remote command 23. VirtualTach Fine tune: adds or subtracts crank time in VirtualTach mode in order to overcome engine types that short crank or over-crank on the first start attempt © 2011 Directed Electronics. All rights reserved.
-
Page 20: Basic Remote Functions
1 minute or until the ignition is turned off. Refer to table of zones. Note: The Warn Away triggers are not stored to memory and is not reported. © 2011 Directed Electronics. All rights reserved. -
Page 21: Table Of Zones
Reducing the sensitivity can solve this problem. Door locks operate backwards. • This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have re- versed these. © 2011 Directed Electronics. All rights reserved. -
Page 22: Troubleshooting: Remote Start
4. Is an ignition or accessory output wire connected to the starter wire of the vehicle? Verify the color of the starter wire in the vehicle and confirm that an ignition or an accessory output is not connected to that wire. © 2011 Directed Electronics. All rights reserved. - Page 23 • The E-brake wire connected to the neutral safety input of the system has a poor ground. Clean the contacts on the switch or replace the switch. © 2011 Directed Electronics. All rights reserved.
Need help?
Do you have a question about the Viper 5904 and is the answer not in the manual?
Questions and answers