A/V Receiver (Stereo System); Satellite Receiver Or Other Device With S-Video - Mitsubishi Electric WD-52628 Owner's Manual

Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video

A/V Receiver (Stereo System)

Figure 7
Most setups require either a digital audio cable or stereo audio
cables. In some circumstances, you may need to connect both
digital audio and stereo audio. A digital audio cable is provided
with the TV. Stereo audio cables are not included.
A. To connect an analog A/V receiver:
Connect a set of stereo audio cables from AUDIO
OUTPUT on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
B. To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
COMPONENT COMPONENT
YPbPr (480i/480p/720p/1080i) YPbPr (480i/480p/720p/1080i)
INPUT INPUT
1 1 2 2
1 1 2 2
Y Y
S-VIDEO S-VIDEO S-VIDEO
Pb Pb
Pr Pr
VIDEO VIDEO
AUDIO- AUDIO-
AUDIO- AUDIO-
LEFT/ LEFT/
LEFT/ LEFT/
(MONO) (MONO)
(MONO) (MONO)
AUDIO- AUDIO- AUDIO- AUDIO-
RIGHT RIGHT
RIGHT RIGHT
MONITORLINK™/HDMI MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR AUDIO PCM LINEAR
1 1
IR EMITTER IR EMITTER
Net Command Net Command
DTV/CABLE/ DTV/CABLE/
VHF/UHF VHF/UHF
DIGITAL
AUDIO
ANT 1 / MAIN ANT 1 / MAIN OUTPUT CableCARD™ CableCARD™ ANT 1 CARD TOP ANT 1 CARD TOP
ANT 2 / AUX ANT 2 / AUX USE WITH USE WITH
Figure 7. Connecting an A/V receiver
On rare occasions, an HDMI signal may be copy-
restricted and cannot be output from the TV as a digital
signal. To hear these copy-protected signals through the
A/V receiver, use connections for analog A/V receivers.
MP3 audio from memory cards cannot be output as
digital audio. To listen to MP3 playback from the TV
memory card player through your A/V receiver, use the
connections for an analog A/V receiver
Check the A/V receiver's Owner's Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.
28
Chapter 2. Connecting
INPUT INPUT OUTPUT OUTPUT
DVI DVI AUDIO AUDIO RECORD RECORD
Analog Audio Analog Audio OUTPUT OUTPUT OUTPUT OUTPUT
1 1 2 2
VIDEO VIDEO
AUDIO- AUDIO-
LEFT/ LEFT/
(MONO) (MONO)
AUDIO- AUDIO-
RIGHT RIGHT
PC - 60Hz PC - 60Hz
VGA, W-VGA, VGA, W-VGA,
SVGA, W-SVGA, SVGA, W-SVGA,
XGA, 1280 X 720 XGA, 1280 X 720
2 2
IEEE 1394 IEEE 1394
INPUT/ INPUT/
OUTPUT OUTPUT
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 S-VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO
on the TV back panel. The red cable connects to the
R (right) channel and the white cable connects to the
L (left) channel.
Note: Refer to the Satellite Receiver Owner's Guide
for Dish Antenna connections
INPUT
1 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
IR EMITTER
Net Command
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN
Figure 8. Connecting a Satellite Receiver with S-Video
Note: NetCommand® assumes you connected your
satellite receiver to Input-2. If you add a second
satellite receiver or use any other inputs for your
satellite receiver, this change must match in the
NetCommand system. See Editing NetCommand
Setup in Chapter 3 for more information.
COMPONENT
YPbPr (480i/480p/720p/1080i)
1 2
INPUT
OUTPUT
Y
DVI AUDIO
RECORD
Analog Audio OUTPUT OUTPUT
Pb
1 2
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITORLINK™/HDMI
PC - 60Hz
VIDEO 480i/480p/720p/1080i
VGA, W-VGA,
AUDIO PCM LINEAR
SVGA, W-SVGA,
XGA, 1280 X 720
1 2
DIGITAL
AUDIO
ANT 2 / AUX OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
IEEE 1394
INPUT/
OUTPUT