Table of Contents
Advertisement
Connecting an A/V Receiver or Stereo System or
a Satellite Receiver or Other Device with S-Video
A/V Receiver or Stereo System
Figure 7
A digital audio cable and stereo audio cables are required. The
digital audio cable is provided. The stereo audio cables are not
included with the TV.
1. Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V Receiver. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
To connect a digital A/V Receiver with Dolby®
Digital surround sound:
2. Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V Receiver.
Check A/V Receiver's Owner's Guide for information
concerning the use of the digital input and switching
between the digital sound and analog stereo sound
from the TV.
TV back panel
2.
ANT- T T 1
MAIN
DIGITAL
DIGITA
T T L
AUDIO
AUDIO
CableCARD
T
LE /V / / HF/UHF)
–
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ANTENNA
AM
75Ω
GND
300Ω
FM
ON
AUDIO
IN
IN
OUT
AUX
CD
TAPE 1
Figure 7. Connecting an A/V Receiver
INPUT
MONITOR OUTPUT
AUDIO/VIDEO 1
1
2
AUDIO 2
White
AUDIO-
LEFT/
(MONO)
IR EMITTER
NetCommand
R
1.
AUDIO-
RIGHT
Red
COM
YPbPr (4
1
ADJUSTMENTS.
Use only if
connecting
a Dolby Digital
A/V Receiver
A/V Receiver Rear Panel
AVIS
!
RISQUE DE CHOC ELECTRONQUE
REC
PRE OUT
NE PAS ENLEVER
SOURCE
SURROUND
SUR.
FRONT
THIS DEVICE COMPLIES WITH PART 15 OF THE
LINE OUT
SPEAKERS (6Ω MIN.)
FCC RULES. OPERATION IS SUBJECT TO THE
2.
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
L
CENTER
MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
L
RECEIVED, INCLUDING INTERFERENCE THAT MAY
SUB
CAUSE UNDESIRED OPERATION.
R
WOOFER
S-VIDEO
R
MONITOR
VCR 1
VCR 2
TV
DVD
FRONT
CENTER
FRONT
OUT
OUT
IN
OUT
IN
IN
IN
SPEAKERS-A (6Ω MIN.)
(6Ω MIN.)
SPEAKERS-B (6Ω MIN. )
MONITOR
VCR 1
VCR 2
TV
DVD
VIDEO
ATUO
OUT
OUT
IN
OUT
IN
IN
IN
L
STANDBY
L
OFF
MITSUBISHI
σ
White
τ
R
AUDIO/VIDEO RECEIVER
M-VR1000
MODEL
POWER SUPPLY
120V-60Hz
POWER CONSUMPTION
552W, 732VA
L
DISTRIBUTED BY
MITSUBISHI CONSUMER ELECTRONICS AMERICA
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING
INC.
CORPORATION. "DOLBY", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE
TRADEMARKS OF DOLBY LABORATORIES CORPORATION.
1.
6100 ATLANTIC BLVD
MADE IN
R
JAPAN
COPYRIGHT 1992 DOLBY LABORATORIES, INC. ALL RIGHTS
NORCROSS, GA 30071-1305
FABRIQUE EN
IN
OUT
IN
OUT
IN
OUT
IN
IN
IN
JAPAN
RESERVED
Red
TAPE 2
VCR 1
VCR 2
TV
DVD
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO,
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner's
Guide for Dish Antenna connections.
Any S-Video Device
White
2.
1
Red
Figure 8. Connecting a Satellite Receiver with S-Video
Note: NetCommand® will asssume you
connected your Satellite Receiver to Input-2.
If you add a second Satellite Receiver or use
any other inputs for your Satellite Receiver,
this change must match in the NetCommand
INPUT-1
(OPTICAL)
INPUT-2
(COAXIAL)
system. See Edit NetCommand... pages 35-42
INPUT-3
(COAXIAL)
DIGITAL AUDIO
for more information.
SWITCHED
UNSWITCHED
AC 120V - 60Hz
TOTAL 100W, 0.9A MAX
AC OUTLETS
For digital audio connections, see your
A/V Receiver, DVD and Satellite Receiver
Owner's Guides.
TV back panel
2.
White
AUDIO OUT
AUDIO IN
VIDEO OUT
L
L
(Y/C)
Red
2
2
R
R
R
1.
DIGITA
T T L
AUDIO
CableCARD
TM
SLOT
IMPORTANT
INPUT
1
1
2
1.
DIO-
MINIMUM BRIGHTNESS, MEASUREMENT
PROCE DURE S AND PR OPE R SE RV ICE
ADJUSTMENTS.
19
Hide quick links:
Advertisement
Table of Contents
