A/V Receiver Or Stereo System; Satellite Receiver Or Other Device With S-Video - Mitsubishi Electric WD-52825 Owner's Manual

Connecting an A/V Receiver or Stereo System or
a Satellite Receiver or Other Device with S-Video

A/V Receiver or Stereo System

Figure 7
A digital audio cable and stereo audio cables are required. The
digital audio cable is provided. The stereo audio cables are not
included with the TV.
1. Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
To connect a digital A/V receiver with Dolby®
Digital surround sound:
2. Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
Check A/V receiver's Owner's Guide for information
concerning the use of the digital input and switching
between the digital sound and analog stereo sound
from the TV.
1.
Red
TV back panel section
IEEE1394
INPUT/OUTPUT
PC
IR EMITTER
VGA/SVGA/XGA/
NetCommand R
720p
60 Hz
R R
L
DVI
L
Analog Audio
R R
ANT-2
PC-
AUX
AUDIO
DTV/
CABLE/
VHF/
UHF
ANT-1
HDMI PC-
M-LINK MAIN INPUT
M-LINK
CONTROL/
RS-232C
DIGITAL DIGITAL
AUDIO AUDIO
Use only if
2.
connecting
a Dolby Digital
A/V Receiver
A/V Receiver Rear Panel
WARNING AVIS
!
RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRONQUE REC PRE OUT
DO NOT OPEN NE PAS ENLEVER
SOURCE
SURROUND
SUR. FRONT
LINE OUT SPEAKERS ���� MIN.�
L CENTER
ANTENNA
SUB
R
WOOFER
AM 75�
S-VIDEO
MONITOR VCR 1 VCR 2 TV DVD
GND
OUT OUT IN OUT IN IN IN
SPEAKERS-A ���� MIN.�
300�
MONITOR VCR 1 VCR 2 TV DVD
VIDEO
ATUO OUT OUT IN OUT IN IN IN
STANDBY L
FM ON OFF
White �
AUDIO
�
L L
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING
CORPORATION. "DOLBY", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE
R R TRADEMARKS OF DOLBY LABORATORIES CORPORATION.
Red
IN IN OUT IN OUT IN 1. OUT IN OUT IN IN IN IN COPYRIGHT 1992 DOLBY LABORATORIES, INC. ALL RIGHTS
RESERVED
AUX CD TAPE 1 TAPE 2 VCR 1 VCR 2 TV TV DVD
Figure 7. Connecting an A/V receiver
24
White
AUDIO AUDIO
MONITOR MONITOR
VIDEO S-VIDEO
OUTPUT OUTPUT
L(MONO) L(MONO)
AUDIO 2 AUDIO 2
AUDIO/VIDEO 1
INPUT-1
INPUT-2
2.
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
INPUT-1
MAY NOT CAUSE HARMFUL INTERFERENCE AND
(OPTICAL)
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
L RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
INPUT-2 INPUT-2
(COAXIAL) (COAXIAL)
R
INPUT-3
(COAXIAL)
FRONT CENTER FRONT
��� MIN.� SPEAKERS-B ���� MIN. �
DIGITAL AUDIO
L
MITSUBISHI
AUDIO/VIDEO RECEIVER
R
MODEL M-VR1000
POWER SUPPLY 120V-60Hz
POWER CONSUMPTION 552W, 732VA
SWITCHED UNSWITCHED
DISTRIBUTED BY
MITSUBISHI CONSUMER ELECTRONICS AMERICA AC 120V - 60Hz
INC.
TOTAL 100W, 0.9A MAX
6100 ATLANTIC BLVD MADE IN AC OUTLETS
JAPAN
NORCROSS, GA 30071-1305 FABRIQUE EN
JAPAN
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO,
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner's
Guide for Dish Antenna connections.
TV back panel section
IEEE1394
INPUT/OUTPUT
PC
IR EMITTER
VGA/SVGA/XGA/
NetCommand
R
720p
60 Hz
DVI
L
Analog Audio
R
ANT-2
AUX
DTV/
CABLE/
VHF/
UHF
HDMI ANT-1
M-LINK MAIN
M-LINK
CONTROL/
RS-232C
DIGITAL
AUDIO
Any S-Video Device
White
2.
Red 1
Figure 8. Connecting a Satellite Receiver with S-Video
Note: NetCommand® will asssume you
connected your Satellite Receiver to Input-2.
If you add a second Satellite Receiver or use
any other inputs for your Satellite Receiver,
this change must match in the NetCommand
system. See Editing NetCommand Setup in
Chapter 3 for more information.
AUDIO AUDIO
MONITOR
VIDEO S-VIDEO
R L(MONO) OUTPUT
R L(MONO)
L
AUDIO 2
R
PC- AUDIO/VIDEO 1
AUDIO
INPUT-1
INPUT-2 INPUT-2
PC-
INPUT
1.
Red White
2.
1.
AUDIO OUT AUDIO IN VIDEO OUT
L L (Y/C)
2
R
R