Related Manuals for General Lock CX480-DN
Summary of Contents for General Lock CX480-DN
-
Page 1: Installation Instructions
CX480-DN Users Manual and Installation Instructions CX480-DN Day/Night Camera Users Manual and Installation Instructions... -
Page 2: Safety Warning
Safety Warning 1. Do not expose the camera to humidity and dust. Moisture can damage the camera and cause the danger of electric shock. If the camera is mounted outdoors, a camera housing is required. Do not install the camera at where there is greasy smoke or steam, where the humidity is too high, or where there is a lot of dust to prevent damages to the camera. - Page 3 5. Never face the camera toward the sun. Never aim the camera at the sun or other extremely bright objects whether it is in use or not. 6. Do not install the camera in the high temperature environment. Installed the camera away from stoves, or other heat generating devices, or where it could be subject to direct sunlight as the high temperatures could cause deformation, discoloration or other damages of the camera.
- Page 4 CX480-DN Introduction The Day/Night Digital Color Camera introduces a new level of high quality picture. The compact, full performance, general-purpose color DSP Cameras, which use high sensitive 1/3" interline transfer Super HAD CCDs (Charge Coupled Device). It delivers high-resolution superior color images in bright light, and clear sharp monochrome pictures in low light.
-
Page 5: Specification
Specification Pickup device: 1/3” interline transfer color CCD Video format: NTSC/PAL Scanning system: NTSC:525 lines, PAL:625 lines Picture elements: NTSC:768 (H) x 494 (V) ; PAL: 752(H) x 582(V) Horizontal resolution: 480 TV lines Sensitivity: 1.0 lux / F=1.2 S/N ratio: >... - Page 6 Sync. mode: Internal sync. / Line lock V Phase adjustment: Line Phase: 0~354° , 60 steps var. on screen Gamma correction: 7 modes selectable on screen Video output: BNC VBS, 1.0Vp-p, 75 ohm Mini Dim S-Video, Y: 1.0Vp-p, 75ohm, C: 286mV, 75ohm(NTSC); S-Video: 300mV, 75ohm(PAL) Day/Night:...
- Page 7 Major Parts Names and their Functions <CX480-DN> ± ″ → → ↓ ≥ ≥ ↓ ° ° ← ← ↑ × ↑ ″ ± ″ ± ∝ → → ↓ ↓ ≥ ≥ ° ° ↑ ← ← ↑ ×...
- Page 8 ←Video Output Connector × Ground Connector This connector is used to connect with the VIDEO IN Connecting to power system ground. connector of the monitor (Video Out: BNC type). ∝ Auto Iris Lens Connector ↑ Power LED Indicator This connector is used to connect with the auto iris lens by a 4-pin male connector.
-
Page 9: Mounting The Lens
Mounting The Lens 1. Remove the cover cap from the top of the lens mount. 2. If C mount lens is used, please add the C adaptor mount ring (the 5mm thick ring in the accessory pack) on top of the lens mount. 3. - Page 10 Connections 1. Connect the video output of the camera to a color monitor or other video device through a 75 ohm type coaxial cable with BNC female connector at camera end. Plug the power cord to the electrical outlet 90~265VAC. Power LED indicates red light if the power source is properly connected.
- Page 11 Settings • Entering the Set Up Menu • Changing the settings Press the tact switcher twice to enter Move to select the item you main menu shown as below: would like to change. To change the settings, use to modify the previous SWITCH SETUP settings.
- Page 12 Iris(AI). internal sync. The default EXPOSURE setting is ES. The default LINELOCK setting is ON. 2. You can do further setting on the next • AWB page after selecting one of the modes. 1. Normally the AWB (Auto White Balance) SWITCH SETUP is set to ON.
- Page 13 are: “Space”, “0~9”, “A~Z”, “a~z”. 3. When the setting is off, it is only a color Press to start editing camera ID and CCD camera. then press to select the The default DAY/NIGHT setting is ON. necessary character then move •...
- Page 14 • EXIT As soon as the default is loaded, Program VER N.N will be shown on the screen. Press to exit the setting mode; or press to go to next setting pages. Once you exit the set up menu, all of the modifications will be Caution: saved.
-
Page 15: Engineering Settings
Engineering Settings The second page is for you to do more 1. LEVEL<IRE> settings of exposure. The setting function This parameter, range from 60~120, is of the second page will be different to adjust the brightness of exposure according to the EXPOSURE setting on levels. -
Page 16: Blc Level
3. SHUTTER LIM 5. BLC LEVEL This parameter, range from 0 ~ 255, is The range of ES is from 1/500 to 1/100,000 seconds. Under ES mode, to adjust the Back Light Compensation you can select the electronic shutter levels. In the back light condition, set speed limit depending on the different BLC ON to obtain the brighter image light conditions. - Page 17 The default AGC MAX setting is 187. 1. SHUTTER SPD You can select the manual exposure speed 8. AGC MIN of 1/60(1/50), 1/100(1/120), 1/250, 1/500, When AGC is on, you can set the 1/1000, 1/2000, 1/4000, 1/10000 by minimum value of AGC from 0 ~ AGC moving MAX.
- Page 18 2. BLC, BLC LEVEL, AGC, AGC MAX, and AGC MIN functions are the same setting procedure as EXPOSURES ES. • EXPOSURE FL Select the Flickerless mode to remove the picture flicker when using a NTSC version camera in 50Hz power source and under fluorescent light;...
-
Page 19: Video Setup
• VIDEO SETUP adjust the chroma of the video. The default CHROMA setting is 10. VIDEO SETUP 3. HUE BRIGHT This parameter, range from 0~20, is for you CHROMA to adjust the hue of the video. The default HUE setting is 10. SHARPNESS HL SHARPNESS HH 4. - Page 20 1. Y GAMMA SHARPNESS G This parameter, range from 0~7, is for you This parameter, range from 0~15, is for you to adjust the Y Gamma Correction Curve. to adjust sharpness gain control. The default Y GAMMA setting is 03. The default SHARPNESS G setting is 10.
- Page 21 Abbreviation Pattern Horizontal color bar HCVR Horizontal color bar Vertical ramp Vertical color bar VCHR Vertical color bar Vertical ramp Monochrome raster Horizontal monochrome ramp Vertical monochrome ramp Horizontal impulse Horizontal reverse impulse Vertical impulse You can adjust W4 position and size; W0, Vertical reverse impulse W1, W2, W3 position and size will Horizontal simple ramp...
- Page 22 the OPD window; press change the length of the OPD window. • OPD WEIGHT SETUP Window OPD WEIGHT SETUP W0 WEIGHT W1 WEIGHT W2 WEIGHT W3 WEIGHT • LINELOCK SETUP EXIT LINELOCK SETUP 1. W0 WEIGHT: 0 ~ 15 VPHASE 2.
- Page 23 to match the vertical phase for both 2. SPEED video output signals as closely as possible. This parameter, range from 01 ~ 14, is to adjust speed of auto white balance. When The default V PHASE setting is 00. the value is larger, the speed is slower. •...