Black Horse Model Focke-Wulf FW190A Instruction Manual

Black Horse Model Focke-Wulf FW190A Instruction Manual

Black horse bh87 model aircraft instruction manual

Advertisement

Instruction Manual book
SPECIFICATION
Wingspan :
Length
Weight
Radio
Servo
Engine
1,780 mm
:
1,520 mm
:
4.8 kg
:
06 channels.
:
09 servos.
:
120
70.08 in.
59.84 in.
10.56 Lbs.
4stroke
Made in Vietnam.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Focke-Wulf FW190A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Black Horse Model Focke-Wulf FW190A

  • Page 1 Instruction Manual book SPECIFICATION Wingspan : 1,780 mm 70.08 in. Length 1,520 mm 59.84 in. Weight 4.8 kg 10.56 Lbs. Radio 06 channels. Servo 09 servos. Engine 4stroke Made in Vietnam.
  • Page 2 Item code:BH87 INSTRUCTION MANUAL. This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your Focke-Wulf FW190A. Use the parts listing below to identify all parts. WARNING. Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is capable of causing injury to people or property.
  • Page 3: Safety Precaution

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else.
  • Page 4: Installing The Aileron Servos

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. REPLACEMENT SMALL PARTS 3 x 15mm 4 x 30mm 1.Door mounting wheel. 2.Air retract main gear. 3.Wheels. 4. Tail gear set. 5. Plastic for tail gear. I. AILERON. 6. Battery tray. 7. Fuel tank.
  • Page 5 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. C/A glue. Aileron Flap Bottom side C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. C/A glue. Bottom side C/A glue. Aileron Flap Repeat the procedure for the other wing half.
  • Page 6 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 4) Drill 1,6mm pilot holes through the block of wood for each of the four mounting screws provided with the servo. 5. Instal servo tray with aileron servo into the wing as same as picture below.
  • Page 7: Installing The Aileron Linkages

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 3.INSTALLING THE AILERON LINKAGES. Installing the aileron linkages as pictures below. 65mm M2 lock nut C/A glue. II. FLAP. 1.INSTALLING THE FLAP SERVOS. Control horn of the aileron thread Repeat the procedure for the other wing...
  • Page 8 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Electric 2x10mm. Secure. 2. INSTALLING THE FLAP CONTROL HORN. Nilon control clasp Flap control horn. 3mm x 30mm. 3.INSTALLING THE FLAP LINKAGES. Installing the aileron linkages as pictures below.
  • Page 9 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 65mm M2 lock nut C/A glue Repeat the procedure for the other wing half. INSTALLING AIR RETRACTABLE LANDING GEAR. 3 x 15mm Secure 3 x 15mm 3 x 15mm 3 x 16mm 3 x 10mm...
  • Page 10 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL.
  • Page 11 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Secure Lock nut 3 x 16 mm 3 x 10 mm Secure.
  • Page 12: Wing Attachment

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. WING ATTACHMENT. Locate the aluminium wing dihe- dral brace. *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the...
  • Page 13 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Epoxy glue. C/A glue FUSELAGE-CANOPY AND PILOT. C/A glue...
  • Page 14: Installing The Engine Mount

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. C/A glue INSTALLING THE ENGINE MOUNT. FUEL TANK. See pictures below: INSTALLING THE STOPPER ASSEMBLY 1) The stopper has been pre-assembled at the factory. 2) Using a modeling knife, cut one length 4 x 30mm...
  • Page 15 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. When the stopper assembly is installed in the 8) Feed three lines through the fuel tank tank, the top of the vent tube should rest just compartment and through the pre-drilled hole below the top surface of the tank. It should not in the firewall.
  • Page 16: Installing The Engine

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. INSTALLING THE ENGINE. Locate the long piece of wire used for the throttle pushrod. One end of the wire has been pre-bend in to a “Z” bend at the factory. This “Z” bend should be inserted into the throttle arm of the engine when the engine is fitted onto the engine mount.
  • Page 17 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Trim and cut 4 x 30mm Bottom side 1. Slide the fiberglass cowl over the en- gine and line up the back edge of the cowl with Secure the marks you made on the fuselage.
  • Page 18: Installing The Spinner

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. INSTALLING THE SPINNER. Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 12mm wood screws. Trim and cut Right side 3 x 12mm Left side Machine screw.
  • Page 19: Horizontal Stabilizer

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. INSTALLING THE THROTTLE PUSHROD. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the Cut.
  • Page 20 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Check to mark sure the wing and stabi- lizer are paralell. If they are not, lightly sand the opening in the fuselage for the stabilizer until the stabilizer is paralell to the wing. C/A glue...
  • Page 21 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 2 Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it. Remove R e m o v e covering covering 3. Mark the shape of the vertical on the left and right sides onto the horizontal stabilizer using a left-tip pen.
  • Page 22: Elevator Control Horn Installation

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 6. After the epoxy has fully cured, remov the masking tape or T-pins used to hold the stabilizer in place and carefully inspect the glue joints. Use more epoxy to fill in any gaps that were not filled previously and clean up the excess using a paper towel and rubbing alcohol.
  • Page 23: Vertical Installation

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Elevator Elevator pushrod pushrod Secure. C/A glue VERTICAL INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Rudder servo C/A glue C/A glue...
  • Page 24 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 4. Now, remove the rudder and using a modeling knife, carefully cut just inside the marked lines and remove the film of the rud- der. Just as you did with the horizontal stabi- lizer, make sure you only press hard enough to cut the film, not the balsa rudder.
  • Page 25: Rudder Control Horn Installa- Tion

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. 6) When you are sure that everything is a aligned correctly, mix up a generous amount Epoxy glue of 30 minute epoxy. Apply a thin layer to the slot in the mounting platform and to the verti- cal stabilizer mounting area.
  • Page 26 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Nilon control clasp M3 lock nut. M3 lock nut. 3mm x 70mm. Control horn of Rudder. M2 lock nut Elevator pushrod Rudder pushrod...
  • Page 27: Mounting The Tail Wheel Bracket

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Secure Rudder Control horn. MOUNTING THE TAIL WHEEL BRACKET. M2 lock nut. 3x12mm 1. Set the tail wheel assembly in place on the plywood plate. The pivot point of the tail wheel wire should be even with the rud- der hinge line and the tail wheel bracket should be centered on the plywood plate.
  • Page 28 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Cut. C/A glue C/A glue Elevator Elevator pushrod pushrod Rudder Rudder pushrod. pushrod.
  • Page 29 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. INSTALLATION SERVO AIR RETRACT- ABLE LANDING GEAR . Servo arm. Secure...
  • Page 30: Installing The Switch

    Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Tie wrap. 3 way connector. Air supply INSTALLING THE SWITCH. 1) Cut out the switch hole using a modeling Air tank knife. Use a 2mm drill bit and drill out the two mounting holes through the fuselage side.
  • Page 31 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. INSTALLING THE RECEIVER AND BATTERY. 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier Receiver when you are installing the wing .
  • Page 32 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. Wing bolt. Mark point secure C/A glue. Mark point...
  • Page 33 Focke-Wulf FW190A- Item code:BH87 INSTRUCTION MANUAL. C/A glue BALANCING. 1) It is critical that your airplane be bal- anced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 135MM BACK FROM THE LEADING EDGE OF THE WING.
  • Page 34: Pre-Flight Check

    6) Properly balance the propeller. We wish you many safe and enjoyable flights with your Focke-Wulf FW190A. CONTROL THROWS. 1) We highly recommend setting up a plane using the control throws listed.

This manual is also suitable for:

Focke-wulf fw190a bh87

Table of Contents