R56Ci Break-in Period Allow several hours of listening time to adequately break-in the Impression Series speakers. As the speakers break-in, the driver suspensions will loosen. The result of break-in will be an increase in low frequency response, improved definition, and increased clarity and detail.
These rigid cones resist flexing and contribute to the accurate reproduction of the audio signal, providing higher overall sound quality. A quality fabric dome tweeter is used for high frequencies in Impression Series speakers. Higher power handling is achieved through the use of magnetic liquid cooling in the tweeter.
Page 5
Good results can usually be obtained by placing a subwoofer along a wall 1-3 feet from a corner. Experiment with placement of the subwoofer and the sub-amplifier controls to achieve the proper bass balance. Impression Series Owner’s Manual...
Page 6
5 speaker plus subwoofer requirement. Dolby Digital EX and DTS ES add a center rear speaker. Dolby TrueHD and DTS Master Audio available only on Blu-ray disc, generally have a 7.1 requirement. Please consult your audio/video professional to determine which system is best for you and how many speakers you will require. Impression Series Owner’s Manual...
Page 7
8. Power supply cords should be routed so they are not likely to be walked on or pinched by items placed upon or against them. 9. Any service or repair required must be performed by qualified, authorized technician. Impression Series Owner’s Manual...
Page 8
L and R terminals. 7. LFE In: The Low Frequency Effect input is to connect to the “LFE” bass management output of the receiver or processor and may also be called “Subwoofer Output”. Impression Series Owner’s Manual...
Page 9
If the replacement fuse is not of the same value, damage to the Subwoofer Amplifier may result. CAUTION! Before replacing the fuse, disconnect the power cord from the power receptacle. 10. Power: Power on and off switch. 2011 + Impression Series Subwoofer Diagram. Impression Series Owner’s Manual...
Page 10
Tower Speaker Outrigger Installation Use these attractive, tower speaker outriggers for the Impression Series tower speakers to create a wider support base for the cabinet. These outriggers make your tower speakers more stable, and are ideal when placing them on a thickly carpeted floor.
” (197mm) D Cabinet: High-gloss Red Burl or High-gloss Red Burl or High-gloss Red Burl or High-gloss Black Ash High-gloss Black Ash High-gloss Black Ash Weight: 52 lbs. (23.59 Kg) 35 lbs. (15.88 Kg) 11.5 lbs. (5.22 Kg) Impression Series Owner’s Manual...
Page 12
19” (483mm) D Cabinet: High-gloss Red Burl or High-gloss Red Burl or High-gloss Red Burl or High-gloss Black Ash High-gloss Black Ash High-gloss Black Ash Weight: 7.5 lbs. (3.40 Kg) 27 lbs. (12.25 Kg) 45 lbs. (20.41 Kg) Impression Series Owner’s Manual...
Page 13
12” (305mm) H ” (216mm) H 6” (152mm) D ” (267mm) D Cabinet: High-gloss Red Burl or High-gloss Red Burl or High-gloss Black Ash High-gloss Black Ash Weight: 12 lbs. (5.44 Kg) 28 lbs. (12.70 Kg) Impression Series Owner’s Manual...
Page 14
Make certain there is an audio signal signal from receiver or processor. from receiver or processor. Amplifier fuse might be blown. Replace fuse (if fuse is not readily accessible, consult with RBH Sound for more information). Performance Crossover frequency is not Adjust the crossover frequency by is less than adjusted correctly.
Warranty Your RBH Sound Impression Series speakers are covered by a limited warranty against defects in materials and workmanship for a period of 5 years, with subwoofer amplifiers covered for 1 year from the original date of purchase. This warranty is provided by the authorized RBH Sound dealer where the speaker was purchased.
Need help?
Do you have a question about the Impression Series and is the answer not in the manual?
Questions and answers